Softex Utilities Installation Guide =================================== Information in this document is subject to change without notice. (c) 1998 Dell Computer Corporation. All rights reserved. Reproduction in any manner whatsoever without the written permission of Dell Computer Corporation is strictly forbidden. Trademarks used in this text: Dell, the DELL logo, and Latitude are registered trademarks of Dell Computer Corporation; Microsoft, and Windows NT are registered trademarks of Microsoft Corporation. Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Computer Corporation disclaims any proprietary interest in trademarks and trade names other than its own. Release: May 2001 Introduction: Softex PC Card Controller Installation Guide ----------------------------------------------------------- The Softex utility provides PC Card control features for your Dell(r) Latitude(r) portable computer running the Microsoft(r) Windows NT(r) operating system. If you have an earlier version of the Softex PC Card Controller installed, remove it before you install the updated PC Card Controller. Refer to Uninstalling the Softex PC Card Controller found later in this document for instructions. If you do not have an earlier version of the Softex PC Card Controller installed, or if you already have uninstalled the previous version of Softex PC Card Controller, you are ready to install the new Softex PC Card Controller. Refer to Installing Softex PC Card Controller found later in this document for instructions. CAUTION: Do not reinstall any version of the Softex utilities earlier than 2.19 if you have installed the Windows NT Service Pack 4. If you do, your system may become unusable. Installation of Softex PC Card Controller should occur with the system undocked, and with any peripheral devices removed from the system. Uninstalling Softex PC Card Controller ------------------------------------------- Perform the following procedure to uninstall the PC Card controller utility: 1. Click the Start button on the Windows NT Taskbar. Click settings, then control panel. 2. In Control Panel click add/remove programs. 3. Highlight Softex PC Card Controller. 4. Click remove. 5. The Softex PC Card Controller Uninstall window appears. NOTE: If the Softex PC Card Controller Uninstall window notifies you that one or more installed PC Card device drivers must be uninstalled prior to removing the Softex PC Card Controller utility, record the devices listed, click OK, and then uninstall each of the listed devices. Refer to Uninstalling PC Card Devices (below) for instructions. 6. Click the icon to begin the uninstallation procedure. 7. When the Softex PC Card Controller Uninstall window notifies you that the uninstallation has successfully completed, click OK. The Reboot Now window appears. 8. Click Restart Now to restart the system. Uninstalling PC Card Devices ---------------------------- Introduction If an error message appears when you attempt to uninstall the PC Card controller utility, make a list of the drivers which must be uninstalled. To uninstall a PCMCIA IDE driver, refer to Uninstalling PCMCIA IDE Drivers for instructions. For uninstallation instructions on all other PC Card device drivers listed, refer to Uninstalling Other PC Card Device Drivers. Uninstalling PCMCIA IDE Drivers ------------------------------- To uninstall the PCMCIA IDE drivers, perform the following steps: 1. Click Start, point to Settings, and then click Control Panel. 2. Double-click the SCSI Adapters icon. 3. Click the Drivers tab. CAUTION: Do not uninstall the CMD CSA-646U Ultra DMA IDE Adapter (if it is listed). If you do, the system may become unusable. 4. Click PCMCIA IDE Driver, and then click Remove. 5. When the Remove Driver window asks if you are sure you want to remove the driver, click Yes. 6. When the driver is successfully removed, click OK. 7. Proceed to Uninstalling Other PC Card Device Drivers for instructions on uninstalling the other drivers on your list. Uninstalling Other PC Card Device Drivers ----------------------------------------- To uninstall the other drivers on your list, perform the following steps: 1. Click Start, point to Settings, and then click Control Panel. 2. Double-click the Network icon. 3. Click the Adapters tab. 4. Click a driver on the list you recorded earlier, and then click Remove. 5. When the Warning window asks you to verify that you want to permanently remove the component, click Yes. The selected device driver is uninstalled. 6. Repeat steps 4 and 5 for all remaining devices drivers you must uninstall. 7. When all necessary drivers have been removed, click Close. 8. When the Network Settings Change window prompts you to restart the system, click Yes. The system restarts. You are now ready to remove the PC Card controller utility. Refer to Uninstalling the PC Card Controller Utility for instructions. Installing Softex PC Card Controller ------------------------------------- Perform the following procedure to install Softex PC Card controller: 1. After downloading the executable file to your hard disk drive. 2. Double click on the self-extracting .EXE file. 3. Information about the software you are installing is displayed. Select "Continue" or "Exit" to continue or abort installation. 4. "Exit" will abort the installion process. "Continue" will allow you to direct where to extract the setup files. 5. Once the files have been extracted, the Setup.exe will be launched and setup will begin. 6. Read and accept the license agreement. NOTE: If you do not accept the license agreement, you cannot install the PC Card controller utility. 7. Click the icon on the Softex PC Card Controller Setup window to accept the default installation directory. The Softex PC Card Controller Setup window monitors the installation and displays a status bar. The Creating Control Panel window appears and notifies you that the setup program will install the Softex PC Card Controller in the Control Panel, and that the PC Card (PCMCIA) icon will be disabled. 8. Click I Understand. 9. When the Softex PC Card Controller Setup window notifies you that the installation is complete, click OK. The Reboot Now window appears. 10. Click Restart Now to restart the system. The system restarts and the Softex PC Card Controller Diagnostics window appears. 11. Click Next>, and then click Next> again to start the diagnostics utility. 12. When the Softex PC Card Controller Diagnostics window notifies you that the diagnostics are complete, click Finish. The system restarts. End of README.TXT =================Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.