OEMSETNT.INF Driver File Contents (PC_A07.EXE)

;****************************************************************************
;
; OEMSETNT.INF
;
; 3Com Megahertz 10/100 LAN + 56K Modem PC Card Windows NT Setup File
;
; Copyright 1998 3Com Corporation
;
;****************************************************************************
;
; Revision History
;
; %ver 1.0f
;
; BFC	07/23/97 1.0a Initial Release for Rev.B EtherDisk
; BFC	08/13/97 1.0b Release for Rev.C EtherDisk
; TES	10/16/97 1.0c Release for FEM556
; BFC	01/19/97 1.0d Release for FEM556
; BFC	01/23/97 1.0e Release for FEM556
; BFC	01/26/97 1.0f Release for FEM556
;****************************************************************************

[Identification]
 OptionType = NetAdapter

[PlatformsSupported]
 ISA
; EISA
; MCA
; PCI
 PCMCIA
 "Jazz-Internal Bus"

[Options]
	FEM556

[OptionsTextENG]
 FEM556 = "3Com Megahertz 10/100 LAN + 56K Modem PC Card (Ethernet)"

[AllFileConstants]
GenericInfVersion = " v1.00"
UtilityInf = "UTILITY.INF"
ParamInf = "NCPARAM.INF"
subroutineinf = "SUBROUTN.INF"
SoftwareType = "driver"
Exit_Code = 0
NetEventDLL = "%SystemRoot%\System32\netevent.dll"
IoLogMsgDLL = "%SystemRoot%\System32\IoLogMsg.dll"
TrayIconExe = "comsmd.exe -try"
UninstallExe = "un3c556"
UnInstallName = "3Com PC Card Diagnostics Utilities"
Manufacturer = "3Com"



[FileConstants-FEM556]
GenericAdapterName = "3Com Megahertz 10/100 LAN + 56K Modem PC Card (Ethernet)"
GenericDriverName = "3Com Megahertz 10/100 LAN + 56K Modem PC Card (Ethernet)"
GenericName = "FEM556"
ProductMajorVersion = "3"
ProductMinorVersion = "51"
ProductVersion = $(ProductMajorVersion)"."$(ProductMinorVersion)
ProductSoftwareName = "FEM556"
ProductSoftwareDescription = "3Com Megahertz 10/100 LAN + 56K Modem PC Card (Ethernet)"
NetRuleSoftwareType = "FEM556Sys ndisDriver FEM556Driver"
NetRuleSoftwareUse = $(SoftwareType)
NetRuleSoftwareBindForm = """FEM556Sys"" yes no container"
NetRuleSoftwareClass = {"FEM556Driver basic"}
NetRuleSoftwareBindable = {"FEM556Driver FEM556Adapter non exclusive 100"}
ProductHardwareName = "FEM556"
ProductHardwareDescription = "3Com Megahertz 10/100 LAN + 56K Modem PC Card (Ethernet)"
NetRuleHardwareType = "FEM556 FEM556Adapter"
NetRuleHardwareBindForm = " yes yes container"
NetRuleHardwareClass = {"FEM556Adapter basic"}
ProductKeyName = $(!NTN_SoftwareBase)"\"$(Manufacturer)"\"$(ProductSoftwareName)"\CurrentVersion"
ParamKeyName = $(!NTN_ServiceBase)"\"$(ProductHardwareName)"\Parameters"
VERS1Manufacturer = "3Com"
VERS1Product = "TX Fast EtherLink PC Card"
VERS1Type		 = "FEM556-FastEtherLink"
PCMCIA			 = 1



[GeneralConstants]
from = ""
to = ""
ExitCodeOk = 0
ExitCodeCancel = 1
ExitCodeFatal = 2
KeyNull = ""
MAXIMUM_ALLOWED = 33554432
RegistryErrorIndex = NO_ERROR
KeyProduct = ""
KeyParameters = ""
TRUE = 1
FALSE = 0
NoTitle = 0
ExitState = "Active"
OldVersionExisted = $(FALSE)
DriverPath = $(!STF_NTPATH)\drivers
NT350VersionConstant = "3.50"
NT310VersionConstant = "3.10"
NT400VersionConstant = "(4.0)"



[date]
 Now = {} ? $(!LIBHANDLE) GetSystemDate


[Identify]
 read-syms Identification

 set Status = STATUS_SUCCESSFUL
 set Identifier = $(OptionType)
 set Media = #("Source Media Descriptions", 1, 1)

 Return $(Status) $(Identifier) $(Media)


[ReturnOptions]
 set Status = STATUS_FAILED
 set OptionList = {}
 set OptionTextList = {}
 set LanguageList = ^(LanguagesSupported, 1)
 Ifcontains(i) $($0) in $(LanguageList)
 ifstr(i) $($1) == ""
 goto returnoptions
 endif

 set PlatformList = ^(PlatformsSupported, 1)
 Ifcontains(i) $($1) in $(PlatformList)
 goto returnoptions
 else
 set Status = STATUS_NOTSUPPORTED
 goto finish_ReturnOptions
 endif
 else
 set Status = STATUS_NOLANGUAGE
 goto finish_ReturnOptions
 endif

returnoptions = +
 set OptionList = ^(Options, 1)
 set OptionTextList = ^(OptionsText$($0), 1)
 set Status = STATUS_SUCCESSFUL

finish_ReturnOptions = +
 Return $(Status) $(OptionList) $(OptionTextList)

[InstallOption]
 set Status = STATUS_FAILED
 set Option = $($1)
 set SrcDir = $($2)
 set AddCopy = $($3)
 set DoCopy = $($4)
 set DoConfig = $($5)

 Set !DebugOutputControl = 0

; Vivek
 set ComPortPrefix = Serial3Com
; Vivek


 set LanguageList = ^(LanguagesSupported, 1)
 Ifcontains(i) $($0) NOT-IN $(LanguageList)
 Return STATUS_NOLANGUAGE
 endif

 set-subst LF = "\n"

 read-syms GeneralConstants
	read-syms AllFileConstants
 read-syms FileConstants"-"$(Option)
 read-syms DialogConstants$(!STF_LANGUAGE)"-"$(Option)
 ifstr(i) $(!NTN_Origination) == "NCPA"
 set Continue = $(OK)
 endif

 read-syms AllFileConstants$(!STF_LANGUAGE)
 read-syms FileConstants$(!STF_LANGUAGE)"-"$(Option)

 detect date

 set-title $(FunctionTitle)

 set to = Begin
 set from = Begin

 ; -------------------------- BEGIN FORCE FIX 

 ; Update the modem info by reading from the ZZZx
 ; entries under the Serial\Parameters in registry

 Debug-Output "<DBG: FORCE> Starting ModemIOBaseAddressList = "$(ModemIOBaseAddressList)
 Debug-Output "<DBG: FORCE> Starting ModemIOBaseAddressValues = "$(ModemIOBaseAddressValues)

 set SerParams = "SYSTEM\CurrentControlSet\Services\Serial\Parameters"

 set ZZZComPort = $(SerParams)"\ZZZa"
 install "install-update-modem-info"

 set ZZZComPort = $(SerParams)"\ZZZb"
 install "install-update-modem-info"

 set ZZZComPort = $(SerParams)"\ZZZc"
 install "install-update-modem-info"

 set ZZZComPort = $(SerParams)"\ZZZd"
 install "install-update-modem-info"

 Debug-Output "<DBG: FORCE> Final ModemIOBaseAddressList = "$(ModemIOBaseAddressList)
 Debug-Output "<DBG: FORCE> Final ModemIOBaseAddressValues = "$(ModemIOBaseAddressValues)

 Debug-Output "<DBG: FORCE> Final ModemIrqList = "$(ModemIrqList)
 Debug-Output "<DBG: FORCE> Final ModemIrqValues = "$(ModemIrqValues)
  ;-------------------------- END FORCE FIX 

 set CommonStatus = STATUS_SUCCESSFUL

 EndWait

Begin = +

 set CurrentVersionValue = ""
 OpenRegKey $(!REG_H_LOCAL) "" "SOFTWARE\Microsoft\Windows Nt\CurrentVersion" $(!REG_KEY_READ) KeyNt
 Ifstr(i) $(KeyNt) != ""
  GetRegValue $(KeyNt) "CurrentVersion" CurrentVersionValue
  Debug-Output "$(InfFile) $(Option): WinNT CurrentVersion ="$(CurrentVersionValue)
  CloseRegKey $(KeyNt)
 Endif

 ifstr(i) (*($(CurrentVersionValue),4)) == $(NT400VersionConstant)
     set NDIS_VER = NDIS4
     set ProductSoftwareImagePath = "\SystemRoot\System32\drivers\FEM556N4.SYS"
 else
     set NDIS_VER = NDIS3
     set ProductSoftwareImagePath = "\SystemRoot\System32\drivers\FEM556N3.SYS"
 endif


 ifstr(i) (*($(CurrentVersionValue),4)) == $(NT310VersionConstant)
  Debug-Output "$(InfFile) $(Option): Configureadapter"
  set Error = "Windows NT v3.10 is not support by this product"
  goto fatal
 endif


 Set ActivateDetection = FALSE

 Ifstr(i) $(!NTN_InstallMode) == deinstall
  set StartLabel = removeadapter
 else-Ifstr(i) $(!NTN_InstallMode) == Update
  set StartLabel = UpgradeSoftware
 else-Ifstr(i) $(!NTN_InstallMode) == bind
  set StartLabel = bindingadapter
 else-Ifstr(i) $(!NTN_InstallMode) == configure
  set StartLabel = configureadapter
  Ifstr(i) $(ProductKeyName) == $(!NTN_RegBase)
   Shell $(UtilityInf),RegistryErrorString,CANNOT_CONFIGURE_SOFTWARE
   ifint $($ShellCode) != $(!SHELL_CODE_OK)
    Debug-Output "ShellCode error: cannot get an error string."
    goto ShellCodeError
   endif
   set Error = $($R0)
   set from = end
   set to = end
   goto nonfatalinfo
  endif
 else
  set StartLabel = installadapter
  set OEM_ABANDON_OPTIONS = {}
  set OEM_ABANDON_SOFTWARE = FALSE
  set OEM_ABANDON_ON = TRUE
 endif


;Vivek
 set IRQValue		= *($(IRQList), 1)
 ;set IRQValue		= *($(IRQList), 5)
;Vivek
 set IOBaseAddrValue	= *($(IOBaseAddrList), 1)
;Vivek
 set MemoryAddrValue = *($(MemoryAddrList), 1)			 ; Memory Address = 0xD0000
 ;set MemoryAddrValue = *($(MemoryAddrList), 9)			 ; Memory Address = 0xD0000
;Vivek
 set ComPortValue = *($(ComPortList), 2)			 ; COM2
 set Static1Label = "Note: Modem and Network use same interrupt"

 Set from = $(fatal)
 Set to = $(fatal)
 Goto $(StartLabel)


installadapter = +
 OpenRegKey $(!REG_H_LOCAL) "" $(ProductKeyName) $(MAXIMUM_ALLOWED) KeyProduct

 Ifstr $(KeyProduct) != $(KeyNull)
  CloseRegKey $(KeyProduct)

  ifstr(i) !(NTN_RegBase) == $(ProductKeyName)
   Shell $(UtilityInf), VerExistedDlg, $(ProductSoftwareTitle),+
	 $(ProductVersion)
   ifint $($ShellCode) != $(!SHELL_CODE_OK)
    Debug-Output "ShellCode error: cannot get an error string."
    goto ShellCodeError
   endif

   goto end
  else
   Shell $(UtilityInf), CardExistedDlg

   ifint $($ShellCode) != $(!SHELL_CODE_OK)
    Debug-Output "ShellCode error: cannot get an error string."
    goto ShellCodeError
   endif

   ifstr(i) $($R1) != "OK"
    goto end
   endif
   set OldVersionExisted = $(TRUE)
  endif
 endif

 Shell $(UtilityInf), DoAskSource, $(!STF_CWDDIR), $(SrcDir) NO

 Ifint $($ShellCode) != $(!SHELL_CODE_OK)
  Goto ShellCodeError
 Else-Ifstr(i) $($R0) == STATUS_FAILED
  Shell $(UtilityInf) RegistryErrorString "ASK_SOURCE_FAIL"
  ifint $($ShellCode) != $(!SHELL_CODE_OK)
   goto ShellCodeError
  endif
  set Error = $($R0)
  Goto fatal
 Else-Ifstr(i) $($R0) == STATUS_USERCANCEL
  Goto successful
 Endif

 Set FileToCheck = $($R1)\OEMSETNT.INF
 LibraryProcedure FilePresent,$(!LIBHANDLE), CheckFileExistance $(FileToCheck)
 Ifstr(i) $(FilePresent) != "YES"
     Goto installadapter
 Endif

 Set SrcDir = $($R1)
 install "Install-Dll"

 Debug-Output "Install-3nicdiag"
 install "Install-3nicdiag"

 StartWait
  ifstr(i) (*($(CurrentVersionValue),4)) == $(NT400VersionConstant)
   Debug-Output "$(InfFile) $(Option): Windows NT 4.00"
   OpenRegKey $(!REG_H_LOCAL) "" "SOFTWARE\Microsoft\Windows\CurrentVersion\Run" $(!REG_KEY_ALL_ACCESS) KeyNt
   set TrayIconList = {COMSMDEXE,$(NoTitle),$(!REG_VT_SZ),$(TrayIconExe)}
   SetRegValue $(KeyNt) $(TrayIconList)
   Debug-Output "Install-TraynCpl"
   install "Install-TrayAndCpl"
   CloseRegKey $(KeyNt)
   RunProgram ExitCode "Windows Directory" "" COMSMD.EXE "-setup"


   OpenRegKey $(!REG_H_LOCAL) "" "SOFTWARE\Microsoft\Windows\CurrentVersion\Uninstall" $(!REG_KEY_ALL_ACCESS) KeyNt
   ifstr $(KeyNt) == ""
     CreateRegKey $(!REG_H_LOCAL) {"SOFTWARE\Microsoft\Windows\CurrentVersion\Uninstall" , 0, GenericClass} "" $(!REG_KEY_ALL_ACCESS) "" KeyNt
   endif
   OpenRegKey $(KeyNt) "" "3ComNicUnInstall" $(!REG_KEY_ALL_ACCESS) KeyNt2
   ifstr $(KeyNt2) == ""
    CreateRegKey $(KeyNt) {"3ComNicUnInstall" , 0, GenericClass} "" $(!REG_KEY_ALL_ACCESS) "" KeyNt2
   endif
   set NewValueList = {{DisplayName, $(NoTitle), $(!REG_VT_SZ), "3Com PC Card Diagnostics"},+
		      {UninstallString, $(NoTitle), $(!REG_VT_SZ), "UN3C556.EXE"}}
   Shell $(UtilityInf), AddValueList, $(KeyNt2), $(NewValueList)
   ifint $($ShellCode) != $(!SHELL_CODE_OK)
    goto ShellCodeError
   endif
   CloseRegKey $(KeyNt)
   CloseRegKey $(KeyNt2)
  endif
 EndWait

 goto adaptersetup


configureadapter = +
 Ifstr $(KeyProduct) == $(KeyNull)
 OpenRegKey $(!REG_H_LOCAL) "" $(!NTN_RegBase) $(MAXIMUM_ALLOWED) KeyProduct
 Ifstr $(KeyProduct) == $(KeyNull)
 set RegistryErrorIndex = CANNOT_FIND_COMPONENT_SERVICE
 Debug-Output "Cannot find component product key"
 goto fatalregistry
 Endif
 Endif

 Debug-Output "INF: Shelling to FindService"
 Shell $(UtilityInf) FindService, $(KeyProduct)
 Ifint $($ShellCode) != $(!SHELL_CODE_OK)
 Debug-Output "INF: FindService shell failure"
 Goto ShellCodeError
 Endif
 Ifstr(i) $($R0) != NO_ERROR
 Debug-Output "INF: FindService Shell error: "$($R0)
 Goto fatalregistry
 endif

 Set KeyParameters = $($R2)

 CloseRegKey $($R1)

 Ifstr $(KeyParameters) == $(KeyNull)
 set RegistryErrorIndex = CANNOT_FIND_COMPONENT_SERVICE
 Debug-Output "Cannot find component service"
 goto fatalregistry
 endif

 set OldVersionExisted = $(TRUE)

 set ValueName = ""
 set ValueData = ""
 set ValueStr = ""
 set ValueList = {}


	EnumRegValue $(KeyParameters) ValueList
 ForListDo $(ValueList)
		set ValueItem = $($)
		set ValueName = *($(ValueItem),1)
		set ValueData = *($(ValueItem),4)
		ifstr(i) $(ValueName) == "IoBaseAddress_1"
		 set IOBaseAddrIndex = $(ValueData)
	 else-ifstr(i) $(ValueName) == "InterruptNumber"
		 set IRQValueIndex = $(ValueData)
	    else-ifstr(i) $(ValueName) == "PCCARDAttributeMemoryAddress"
		set MemoryAddrIndex = $(ValueData)
	    else-ifstr(i) $(ValueName) == "ComPort"
		set ComPortIndex = $(ValueData)
;Vivek
	    else-ifstr(i) $(ValueName) == "AdapterName"
		Debug-Output "<DBG> AdapterName in registry = "$(ValueData)
	    	set OldAdapterName = $(ValueData)
;Vivek
		endif
 EndForListDo

 set IRQValue = *($(IRQList), ~($(IRQValues),$(IRQValueIndex)))
 ifstr(i) $(IRQValue) == ""
		set IRQValue = *($(IRQList), 5)
 endif

 set IOBaseAddrValue = *($(IOBaseAddrList), ~($(IOBaseAddrValues),$(IOBaseAddrIndex)))
 ifstr(i) $(IOBaseAddrValue) == ""
		set IOBaseAddrValue = *($(IOBaseAddrList), 1)
 endif

 set MemoryAddrValue = *($(MemoryAddrList), ~($(MemoryAddrValues),$(MemoryAddrIndex)))
 ifstr(i) $(MemoryAddrValue) == ""
	   set MemoryAddrValue = *($(MemoryAddrValues), 2)
 endif

 set ComPortValue = *($(ComPortList), ~($(ComPortValues),$(ComPortIndex)))
 ifstr(i) $(ComPortValue) == ""
	    set ComPortValue = *($(ComPortValues), 2)
 endif

adaptersetup = +



 LoadLibrary "disk 1" $(DialogDllName) hLib
 read-syms FileDependentDlg$(!STF_LANGUAGE)"-"$(Option)
	set ENABLER = 0


 ui start "InputDlg" $(hLib)

 set ExitButton = $(ButtonPressed)
	FreeLibrary $(hLib)

	ifstr(i) $(DLGEVENT) == "CONTINUE"

		set IOBaseAddrIndex		= $(Combo1Out)
		set IRQValueIndex		= $(Combo2Out)
	    set MemoryAddrIndex 	= $(Combo3Out)
	    set ComPortIndex		= $(Combo4Out)
		set ModemInterruptNumberIndex = $(Combo5Out)
	set ExitButton			= $(ButtonPressed)

		ui pop 1

	else-ifstr(i) $(DLGEVENT) == "EXIT"
		set CommonStatus = STATUS_USERCANCEL
		ui pop 1
		goto end
 else
		set CommonStatus = STATUS_USERCANCEL
		ui pop 1
		Debug-Output "Action: unknown. Bye."
		goto end
 endif


skipoptions =+

 ifint $(OldVersionExisted) == $(TRUE)
 ifstr(i) $(!NTN_InstallMode) == configure
 goto writeparameters
 endif
 endif
 StartWait
 ifint $(OldVersionExisted) == $(FALSE)

 ifstr(i) $(!NTN_InstallMode) == "install"
 Ifstr(i) $(DoCopy) == "YES"

 Shell $(UtilityInf), DoAskSource, $(!STF_CWDDIR), $(SrcDir) YES

 Ifint $($ShellCode) != $(!SHELL_CODE_OK)
 Goto ShellCodeError
 Else-Ifstr(i) $($R0) == STATUS_FAILED
 Shell $(UtilityInf) RegistryErrorString "ASK_SOURCE_FAIL"
 ifint $($ShellCode) != $(!SHELL_CODE_OK)
 goto ShellCodeError
 endif
 set Error = $($R0)
 Goto fatal
 Else-Ifstr(i) $($R0) == STATUS_USERCANCEL
 Goto successful
 Endif

 Set SrcDir = $($R1)

 Endif

 install "Install-Option"

 ifstr(i) $(STF_INSTALL_OUTCOME) != STF_SUCCESS
 Shell $(UtilityInf) RegistryErrorString "UNABLE_COPY_FILE"
 ifint $($ShellCode) != $(!SHELL_CODE_OK)
 goto ShellCodeError
 endif
 set Error = $($R0)
 goto fatal
 endif
 endif



 Shell $(UtilityInf), AddSoftwareComponent, $(Manufacturer), +
 $(ProductSoftwareName), +
 $(ProductSoftwareName), +
 $(ProductSoftwareTitle), $(STF_CONTEXTINFNAME), +
 $(ProductSoftwareImagePath), "kernel", "NDIS", {}, "",+
 $(NetEventDLL)

 Set OEM_ABANDON_SOFTWARE = TRUE

 ifint $($ShellCode) != $(!SHELL_CODE_OK)
 Debug-Output "ShellCode error"
 goto ShellCodeError
 endif
 set RegistryErrorIndex = $($R0)
 set KeyProduct = $($R1)
 Set SoftNetRulesKey = $($R2)
 CloseRegKey $($R3)
 CloseRegKey $($R4)
 CloseRegKey $($R5)

 Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
 EndWait
 Debug-Output "Registry error: add software components"
 CloseRegKey $(KeyProduct)
 CloseRegKey $(SoftNetRulesKey)
 goto fatalregistry
 endif

;Vivek
        ifstr $(AdapterNumber) == ""

                Debug-Output "<DBG> AdpaterNumber unknown !"
                Debug-Output "<DBG> NTN_RegBase = "$(!NTN_RegBase)

                set MyAdapterName = $(!NTN_RegBase)
                Debug-Output "<DBG> MyAdapterName = "$(MyAdapterName)

                Split-String $(MyAdapterName), "\", MyCardInfo
                Debug-Output "<DBG> MyCardInfo = "$(MyCardInfo)

                set AdapterNumber = *($(MyCardInfo),11)
                Debug-Output "<DBG> AdapterNumber = "$(AdapterNumber)
        endif
;Vivek

 set NewValueList = {{SoftwareType,$(NoTitle),$(!REG_VT_SZ),$(SoftwareType)},+
 {MajorVersion,$(NoTitle),$(!REG_VT_DWORD),$(ProductMajorVersion)},+
 {MinorVersion,$(NoTitle),$(!REG_VT_DWORD),$(ProductMinorVersion)},+
 {Title,$(NoTitle),$(!REG_VT_SZ),$(ProductSoftwareTitle)},+
 {Description,$(NoTitle),$(!REG_VT_SZ),$(ProductSoftwareDescription)},+
 {ServiceName,$(NoTitle),$(!REG_VT_SZ),$(ProductSoftwareName)},+
 {InstallDate,$(NoTitle),$(!REG_VT_DWORD),*($(Now),1)}}

 Shell $(UtilityInf), AddValueList, $(KeyProduct), $(NewValueList)
 ifint $($ShellCode) != $(!SHELL_CODE_OK)
 Debug-Output "ShellCode error."
 goto ShellCodeError
 endif

 set RegistryErrorIndex = $($R0)

 Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
 EndWait
 Debug-Output "Registry error: add value list."
 CloseRegKey $(KeyProduct)
 CloseRegKey $(SoftNetRulesKey)
 goto fatalregistry
 endif

 set NewValueList = {{type,$(NoTitle),$(!REG_VT_SZ),$(NetRuleSoftwareType)},+
 {use,$(NoTitle),$(!REG_VT_SZ),$(NetRuleSoftwareUse)}, +
 {bindform,$(NoTitle),$(!REG_VT_SZ),$(NetRuleSoftwareBindForm)}, +
 {class,$(NoTitle),$(!REG_VT_MULTI_SZ),$(NetRuleSoftwareClass)}, +
 {bindable,$(NoTitle),$(!REG_VT_MULTI_SZ),$(NetRuleSoftwareBindable)}, +
 {InfOption,$(NoTitle),$(!REG_VT_SZ),$(Option)}}

 Shell $(UtilityInf), AddValueList, $(SoftNetRulesKey), $(NewValueList)
 ifint $($ShellCode) != $(!SHELL_CODE_OK)
 Debug-Output "ShellCode error."
 goto ShellCodeError
 endif

 set RegistryErrorIndex = $($R0)

 CloseRegKey $(KeyProduct)
 CloseRegKey $(SoftNetRulesKey)

 Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
 EndWait
 Debug-Output "Resgitry error: add value list."
 goto fatalregistry
 endif
 endif

 Shell $(UtilityInf), AddHardwareComponent, $(ProductHardwareName),$(STF_CONTEXTINFNAME),$(ProductKeyName)

 ifint $($R4) != -1
 Set OEM_ABANDON_OPTIONS = >($(OEM_ABANDON_OPTIONS), $(!NTN_SoftwareBase)"\Microsoft\Windows NT\CurrentVersion\NetworkCards\"$($R4))
 endif

 ifint $($ShellCode) != $(!SHELL_CODE_OK)
 Debug-Output "Cannot add hardware component"
 goto ShellCodeError
 endif

 set RegistryErrorIndex = $($R0)

 Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
 EndWait
 Debug-Output "Registry error: add hardware component"
 CloseRegKey $($R1)
 CloseRegKey $($R2)
 CloseRegKey $($R3)
 goto fatalregistry
 endif

 set KeyParameters = $($R3)
 set KeyAdapterRules = $($R2)
 set AdapterNumber = $($R4)

 set NewValueList = {{Manufacturer,$(NoTitle),$(!REG_VT_SZ),$(Manufacturer)},+
 {Title,$(NoTitle),$(!REG_VT_SZ),"["$($R4)"] "$(ProductHardwareTitle)},+
 {Description,$(NoTitle),$(!REG_VT_SZ),$(ProductHardwareDescription)},+
 {ProductName,$(NoTitle),$(!REG_VT_SZ),$(ProductHardwareName)},+
 {ServiceName,$(NoTitle),$(!REG_VT_SZ),$($R5)},+
 {InstallDate,$(NoTitle),$(!REG_VT_DWORD),*($(Now),1)}}

 Shell $(UtilityInf), AddValueList, $($R1), $(NewValueList)
 ifint $($ShellCode) != $(!SHELL_CODE_OK)
 Debug-Output "ShellCode error"
 goto ShellCodeError
 endif

 CloseRegKey $($R1)

 set TempProdName = """"$(ProductHardwareName)$(AdapterNumber)""""
 set TempBindForm = $(TempProdName)$(NetRuleHardwareBindForm)

 set NewValueList = {{type,$(NoTitle),$(!REG_VT_SZ),$(NetRuleHardwareType)},+
 {bindform,$(NoTitle),$(!REG_VT_SZ),$(TempBindForm)}, +
 {class,$(NoTitle),$(!REG_VT_MULTI_SZ),$(NetRuleHardwareClass)}, +
 {InfOption,$(NoTitle),$(!REG_VT_SZ),$(Option)}}

 Shell $(UtilityInf), AddValueList, $(KeyAdapterRules), $(NewValueList)
 ifint $($ShellCode) != $(!SHELL_CODE_OK)
 Debug-Output "ShellCode error."
 goto ShellCodeError
 endif

 set RegistryErrorIndex = $($R0)

 Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
 EndWait
 Debug-Output "Resgitry error: add value list."
 CloseRegKey $(KeyParameters)
 CloseRegKey $(KeyAdapterRules)
 goto fatalregistry
 endif

 CloseRegKey $(KeyAdapterRules)

 goto writeparameters

writeparameters = +


set BusTypeNum = 1
ifint $($ShellCode) != $(!SHELL_CODE_OK)
 Debug-Output "ShellCode error."
 goto ShellCodeError
 endif

    Debug-Output "$(InfFile) $(Option): Write Pcmcia database"
    OpenRegKey $(!REG_H_LOCAL) "" "SYSTEM\CurrentControlSet\Services\Pcmcia\DataBase\3Com\Megahertz 3CCFEM556" $(MAXIMUM_ALLOWED) MyPcmciaHandle
	Debug-Output "CreatRegKey (FEM556)"
	OpenRegKey $(!REG_H_LOCAL) "" "SYSTEM\CurrentControlSet\Services\Pcmcia\DataBase\3Com" $(MAXIMUM_ALLOWED) MyPcmciaHandle
	Ifstr $(MyPcmciaHandle) == $(KeyNull)
	    OpenRegKey $(!REG_H_LOCAL) "" "SYSTEM\CurrentControlSet\Services\Pcmcia\DataBase" $(MAXIMUM_ALLOWED) MyPcmciaKey
	    CreateRegKey $(MyPcmciaKey) {"3Com",0,GenericClass} "" $(MAXIMUM_ALLOWED) "" MyPcmcialHandle
	    CloseRegKey ($MyPcmciaKey)
	endif
	OpenRegKey $(!REG_H_LOCAL) "" "SYSTEM\CurrentControlSet\Services\Pcmcia\DataBase\3Com" $(MAXIMUM_ALLOWED) MyPcmciaKey
	CreateRegKey $(MyPcmciaKey) {"Megahertz 3CCFEM556",0,GenericClass} "" $(MAXIMUM_ALLOWED) "" MyPcmcialHandle
	CloseRegKey ($MyPcmciaKey)
	OpenRegKey $(!REG_H_LOCAL) "" "SYSTEM\CurrentControlSet\Services\Pcmcia\DataBase\3Com\Megahertz 3CCFEM556" $(MAXIMUM_ALLOWED) MyPcmciaHandle
    endif
    set NewValueList = {{Driver,$(NoTitle),$(!REG_VT_SZ),"FEM556"},+
			     {DeviceType,$(NoTitle),$(!REG_VT_SZ),"NET"}}
    Shell $(UtilityInf), AddValueList, $(MyPcmciaHandle), $(NewValueList)
    Debug-Output "<DBG> AddValueList - Driver:REG_SZ:FEM556"
    CloseRegKey $(MyPcmciaHandle)

    set IRQValue	   = *($(IRQValues), ~($(IRQList), $(IRQValueIndex)))
    set IOBaseAddrValue    = *($(IOBaseAddrValues),~($(IOBaseAddrList), $(IOBaseAddrIndex)))
	set ComPortValue = *($(ComPortValues), ~($(ComPortList), $(ComPortIndex)))
        Debug-Output "<DBG> Install/ComPortIndex "$(ComPortIndex)

; Vivek
        ; check if user selected Auto for Interrupt - if so
        ; we should write the correct irq for the modem intr
        ; and write 0 for the network intr.
        ;
        set ModemInterruptNumberValue = *($(IRQValues), ~($(IRQList), $(IRQValueIndex)))
        Debug-Output "<DBG> Install/ModemInterruptNumberValue "$(ModemInterruptNumberValue)

        ifint $(ModemInterruptNumberValue) == 0
                Debug-Output "<DBG> Install/ModemInterruptNumberValue is 0 !"
		Debug-Output "<DBG> Install/ModemIRQValues "$(ModemIrqValues)
		Debug-Output "<DBG> Install/ComPortList "$(ComPortList)
		Debug-Output "<DBG> Install/ComPortIndex "$(ComPortIndex)

                set ModemInterruptNumberValue = *($(ModemIrqValues), ~($(ComPortList),$(ComPortIndex)))
                Debug-Output "<DBG> Install/ModemInterruptNumberValue "$(ModemInterruptNumberValue)
        endif
; Vivek

	set ModemIOBaseAddressValue = *($(ModemIOBaseAddressValues), $(ComPortValue))
	set MemoryAddrValue = *($(MemoryAddrValues),  ~($(MemoryAddrList), $(MemoryAddrIndex)))
;Vivek
	;set-add CommonMemoryAddrValue = $(MemoryAddrValue), 8192
        ifint $(MemoryAddrValue) != 0
                set-add CommonMemoryAddrValue = $(MemoryAddrValue), 8192
        else
                set CommonMemoryAddrValue = 0
        endif

        ifstr $(OldAdapterName) == ""
                set OldAdapterName = $(ProductHardwareName)$(AdapterNumber)
                Debug-Output "<DBG> setting OldAdapterName"
        endif
        Debug-Output "<DBG> OldAdapterName = "$(OldAdapterName)
;Vivek

    set NewValueList = {{IoBaseAddress, $(NoTitle),$(!REG_VT_DWORD),$(ModemIOBaseAddressValue)},+

;Vivek
;	The network interrupt should match modem interrupt in case of Auto

;	 {InterruptNumber, $(NoTitle),$(!REG_VT_DWORD),$(IRQValue)},+
	 {InterruptNumber, $(NoTitle),$(!REG_VT_DWORD),$(ModemInterruptNumberValue)},+
;Vivek
	 {MediaType, $(NoTitle),$(!REG_VT_DWORD),1},+
	 {BusType, $(NoTitle),$(!REG_VT_DWORD),$(BusTypeNum)},+
	 {BusNumber, $(NoTitle),$(!REG_VT_DWORD),0},+
	 {CardType,$(NoTitle),$(!REG_VT_DWORD),0},+
	 {AdapterType,			  $(NoTitle),$(!REG_VT_DWORD),259},+
	 {OSType,			  $(NoTitle),$(!REG_VT_DWORD),1},+
;Vivek
	 {SoftexPcmcia, $(NoTitle),$(!REG_VT_DWORD),1},+
	 {AdapterName,$(NoTitle),$(!REG_VT_SZ),$(OldAdapterName)},+
	 ;{Pcmcia, $(NoTitle),$(!REG_VT_DWORD),1},+
;Vivek

     {LANOnly, $(NoTitle),$(!REG_VT_DWORD),0},+
     {PCCARDAttributeMemoryAddress, $(NoTitle),$(!REG_VT_DWORD),$(MemoryAddrValue)},+
     {PCCARDAttributeMemorySize, $(NoTitle),$(!REG_VT_DWORD),8192},+
     {IOBaseAddress_1, $(NoTitle),$(!REG_VT_DWORD),$(IOBaseAddrValue)},+
     {ModemFunction, $(NoTitle), $(!REG_VT_DWORD),1},+
     {ComPort, $(NoTitle),$(!REG_VT_DWORD),$(ComPortValue)},+
;Vivek
    ; {ModemInterruptNumber, $(NoTitle),$(!REG_VT_DWORD),$(IRQValue)},+
     {ModemInterruptNumber, $(NoTitle),$(!REG_VT_DWORD),$(ModemInterruptNumberValue)},+
;Vivek
     {IoLength, $(NoTitle),$(!REG_VT_DWORD), 7},+
     {IoLength_1, $(NoTitle),$(!REG_VT_DWORD), 31},+
     {MemoryMappedBaseAddress, $(NoTitle),$(!REG_VT_DWORD),$(CommonMemoryAddrValue)},+
     {MemoryMappedSize, $(NoTitle),$(!REG_VT_DWORD),8192},+
	 }

 Shell $(UtilityInf), AddValueList, $(KeyParameters), $(NewValueList)
 CloseRegKey $(KeyParameters)


	OpenRegKey $(!REG_H_LOCAL) "" "SYSTEM\CurrentControlSet\Services\Serial" $(MAXIMUM_ALLOWED) MyNewSerialHandle
	;
	; If we are on WinNt 3.51 then replace serial with serial3.sys driver
	;
	ifstr(i) (*($(CurrentVersionValue),4)) == $(NT400VersionConstant)
		Set NewValueList = { {PermitShare, $(NoTitle),$(!REG_VT_DWORD),1},+
			     {ShareInterrupt,$(NoTitle),$(!REG_VT_DWORD),1}}
;Vivek
;			     {ImagePath,$(NoTitle),$(!REG_VT_SZ),"\SystemRoot\System32\drivers\serial.sys"}}
;Vivek
	else
		Set NewValueList = { {PermitShare, $(NoTitle),$(!REG_VT_DWORD),1},+
			     {ShareInterrupt,$(NoTitle),$(!REG_VT_DWORD),1}}
;Vivek
;			     {ImagePath,$(NoTitle),$(!REG_VT_SZ),"\SystemRoot\System32\drivers\serial3.sys"}}
;Vivek
	endif


       Shell  $(UtilityInf), AddValueList, $(MyNewSerialHandle), $(NewValueList)
	CloseRegKey $(MyNewSerialHandle)

;Vivek
;***************************************************************
Debug-Output "<DBG> Checking if COM port needs to be added ...."
;***************************************************************

ifstr $(AdapterNumber) == ""

        Debug-Output "<DBG> AdpaterNumber unknown !"
        Debug-Output "<DBG> NTN_RegBase = "$(!NTN_RegBase)

        set MyAdapterName = $(!NTN_RegBase)
        Debug-Output "<DBG> MyAdapterName = "$(MyAdapterName)

        Split-String $(MyAdapterName), "\", MyCardInfo
        Debug-Output "<DBG> MyCardInfo = "$(MyCardInfo)

        set AdapterNumber = *($(MyCardInfo),11)
        Debug-Output "<DBG> AdapterNumber = "$(AdapterNumber)
endif

	set ComPortName = $(ComPortPrefix)$(AdapterNumber)
	Debug-Output "<DBG> ComPortName = "$(ComPortName)

	Debug-Output "<DBG> Deleting old "$(ComPortName)
	OpenRegKey $(!REG_H_LOCAL) "" "SYSTEM\CurrentControlSet\Services\Serial\Parameters" $(MAXIMUM_ALLOWED) MyNewSerialHandle

	DeleteRegTree $(MyNewSerialHandle) $(ComPortName)
	CloseRegKey $(MyNewSerialHandle)

	Debug-Output "<DBG> Adding the COM port "$(ComPortName)
;	OpenRegKey $(!REG_H_LOCAL) "" "SYSTEM\CurrentControlSet\Services\Serial\Parameters\Serial3Com" $(MAXIMUM_ALLOWED) MyNewSerialHandle
;	Ifstr $(MyNewSerialHandle) == $(KeyNull)
;Vivek
		OpenRegKey $(!REG_H_LOCAL) "" "SYSTEM\CurrentControlSet\Services\Serial\Parameters" $(MAXIMUM_ALLOWED) SerialKey
;Vivek
		CreateRegKey $(SerialKey) {$(ComPortName),0,GenericClass} "" $(MAXIMUM_ALLOWED) "" MyNewSerialHandle
	;	CreateRegKey $(SerialKey) {"Serial3Com",0,GenericClass} "" $(MAXIMUM_ALLOWED) "" MyNewSerialHandle
;Vivek
		CloseRegKey $(SerialKey)
;Vivek
;	Endif
;Vivek


;Vivek
	Debug-Output "<DBG> ComPortIndex "$(ComPortIndex)
	Debug-Output "<DBG> ModemInterruptNumberValue "$(ModemInterruptNumberValue)
	ifint $(ModemInterruptNumberValue) == 0
		Debug-Output "<DBG> ModemInterruptNumberValue is 0 !"

		set ModemInterruptNumberValue = *($(ModemIrqValues), ~($(ComPortList),$(ComPortIndex)))
		Debug-Output "<DBG> ModemInterruptNumberValue "$(ModemInterruptNumberValue)
	endif
;Vivek
	Set NewValueList = {{DosDevices, $(NoTitle),$(!REG_VT_SZ), "COM"$(ComPortValue)},+                     ; "COMx"
			    {ForceFifoEnable, $(NoTitle),$(!REG_VT_DWORD), 1},+ 			  ; Always true
;Vivek
			    {ExternallyConfiguredModem, $(NoTitle), $(!REG_VT_DWORD), 1},+                        
 ;Vivek
			   ; {Interrupt, $(NoTitle),$(!REG_VT_DWORD), $(IRQValue)},+	    ; Interrupt for MHZ modem
;Vivek
			    {Interrupt, $(NoTitle), $(!REG_VT_DWORD), $(ModemInterruptNumberValue)},+
;Vivek
			    {InterruptMode,$(NoTitle),$(!REG_VT_DWORD),0},+
			    {PortAddress, $(NoTitle),$(!REG_VT_DWORD), $(ModemIOBaseAddressValue)},+ ; Com Io Base Address
			    {PermitShare, $(NoTitle),$(!REG_VT_DWORD), 1 },+
			    {ShareInterrupt, $(NoTitle),$(!REG_VT_DWORD), 1}}

	Shell  $(UtilityInf), AddValueList, $(MyNewSerialHandle), $(NewValueList)
	CloseRegKey $(MyNewSerialHandle)

	;add comm port info to HARDWARE\DEVICEMAP\SERIALCOMM section
	OpenRegKey $(!REG_H_LOCAL) "" "HARDWARE\DEVICEMAP\SERIALCOMM" $(MAXIMUM_ALLOWED) MyNewSerialHandle
	Ifstr $(MyNewSerialHandle) == $(KeyNull)
		OpenRegKey $(!REG_H_LOCAL) "" "HARDWARE\DEVICEMAP" $(MAXIMUM_ALLOWED) SerialKey
		CreateRegKey $(SerialKey) {"SERIALCOMM",0,GenericClass} "" $(MAXIMUM_ALLOWED) "" MyNewSerialHandle
		CloseRegKey $(SerialKey)
	Endif
	SetRegValue $(MyNewSerialHandle) {"Serial3Com",$(NoTitle),$(!REG_VT_SZ),"COM"$(ComPortValue)}
	CloseRegKey $(MyNewSerialHandle)

	; add comm port info to SOFTWARE\Microsoft\Windows NT\CurrentVersion\Ports section
	OpenRegKey $(!REG_H_LOCAL) "" "SOFTWARE\Microsoft\Windows NT\CurrentVersion\Ports" $(MAXIMUM_ALLOWED) MyNewSerialHandle
	Ifstr $(MyNewSerialHandle) == $(KeyNull)
		OpenRegKey $(!REG_H_LOCAL) "" "SOFTWARE\Microsoft\Windows NT\CurrentVersion" $(MAXIMUM_ALLOWED) SerialKey
		CreateRegKey $(SerialKey) {"Ports",0,GenericClass} "" $(MAXIMUM_ALLOWED) "" MyNewSerialHandle
		CloseRegKey $(SerialKey)
	Endif
	SetRegValue $(MyNewSerialHandle) {"COM"$(ComPortValues)":",$(NoTitle),$(!REG_VT_SZ),"9600,n,8,1"}
	CloseRegKey $(MyNewSerialHandle)



 ifint $($ShellCode) != $(!SHELL_CODE_OK)
 Debug-Output "ShellCode error."
 goto ShellCodeError
 endif

 set RegistryErrorIndex = $($R0)

 Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
 Debug-Output "Registry error: Add value list"
 goto fatalregistry
 endif

 EndWait

 goto successful

bindingadapter =+
 set Error = "Binding: Sorry, not yet implemented."
 goto fatal


removeadapter = +
 Ifstr(i) $(ProductKeyName) == $(!NTN_RegBase)

Shell $(UtilityInf), RemoveSoftwareComponent, $(Manufacturer), +
 $(ProductSoftwareName)
 ifint $($ShellCode) != $(!SHELL_CODE_OK)
 Debug-Output "ShellCode error"
 goto ShellCodeError
 endif

 set RegistryErrorIndex = $($R0)

 Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
 goto fatalregistry
 endif
 else
 Shell $(UtilityInf), RemoveHardwareComponent, $(Manufacturer), +
 $(ProductSoftwareName), $(!NTN_RegBase)
 ifint $($ShellCode) != $(!SHELL_CODE_OK)
 Debug-Output "ShellCode error"
 goto ShellCodeError
 endif

 set RegistryErrorIndex = $($R0)

 Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
 goto fatalregistry
 endif

;Vivek
        ;***************************************************************
        ; Remove associated Com port
        ;***************************************************************

        Debug-Output "<DBG> Starting removal of COM PORT .... "
        Debug-Output "<DBG> !NTN_RegBase = "$(!NTN_RegBase)
        Debug-Output "<DBG> Manufacturer = "$(Manufacturer)
        Debug-Output "<DBG> ProductKeyName = "$(ProductKeyName)
        Debug-Output "<DBG> ProductSoftwareName = "$(ProductSoftwareName)

        set AdapterName = $(!NTN_RegBase)
        Split-String $(AdapterName), "\", CardInfo
        Debug-Output "<DBG> CardInfo = "$(CardInfo)
        set AdapterNumber = *($(CardInfo),11)

        set ComPortName = $(ComPortPrefix)$(AdapterNumber)
        Debug-Output "<DBG> ComPortName = "$(ComPortName)

        Debug-Output "<DBG> AdapterNumber = "$(AdapterNumber)

        OpenRegKey $(!REG_H_LOCAL) "" "SYSTEM\CurrentControlSet\Services\Serial\Parameters" $(MAXIMUM_ALLOWED) SerialHandle

        DeleteRegTree $(SerialHandle) $(ComPortName)

        CloseRegKey $(SerialHandle)
;Vivek

 endif
	ifstr(i) (*($(CurrentVersionValue),4)) == $(NT400VersionConstant)
		Debug-Output "$(InfFile) $(Option): Windows NT 4.00 remove icon"
		OpenRegKey $(!REG_H_LOCAL) "" "SOFTWARE\Microsoft\Windows\CurrentVersion\Run" $(!REG_KEY_ALL_ACCESS) KeyNt
		set TrayIconList = COMSMDEXE
		DeleteRegValue $(KeyNt) $(TrayIconList)
		CloseRegKey $(KeyNt)
	endif
	RunProgram ExitCode "Windows Directory" "" UN3C556.EXE "-inf"

goto end


UpgradeSoftware = +
 ifstr(i) $(ProductKeyName) == $(!NTN_RegBase)
 OpenRegKey $(!REG_H_LOCAL) "" $(ProductKeyName) $(MAXIMUM_ALLOWED) KeyProduct

 Ifstr $(KeyProduct) != $(KeyNull)
 GetRegValue $(KeyProduct),"MajorVersion", VersionInfo
 set Version = *($(VersionInfo), 4)

 Shell $(UtilityInf), GetInfFileNameFromRegistry, $(KeyProduct)

 ifint $($ShellCode) != $(!SHELL_CODE_OK)
 Debug-Output "ShellCode error"
 goto ShellCodeError
 endif

 set !UG_Filename = $($R0)

 ifstr(i) $(!UG_Filename) != ""
 install "Install-Update"
 ifstr(i) $(STF_INSTALL_OUTCOME) != STF_SUCCESS
 goto fatal
 endif
 endif

 SetRegValue $(KeyProduct) {MajorVersion,$(NoTitle),$(!REG_VT_SZ),$(ProductMajorVersion)}
 SetRegValue $(KeyProduct) {MinorVersion,$(NoTitle),$(!REG_VT_SZ),$(ProductMinorVersion)}

 ifint $(Version) != $(ProductVersion)
 endif
 CloseRegKey $(KeyProduct)
 else
 goto fatalregistry
 endif
 else
 OpenRegKey $(!REG_H_LOCAL) "" $(!NTN_RegBase) +
 $(MAXIMUM_ALLOWED) NetworkCardKey
 Ifstr(i) $(NetworkCardKey) != $(KeyNull)
 GetRegValue $(NetworkCardKey),"ServiceName", ServiceNameInfo
 set ServiceName = *($(ServiceNameInfo), 4)

 OpenRegKey $(NetworkCardKey) "" "NetRules" +
 $(MAXIMUM_ALLOWED) NetRuleKey
 Ifstr(i) $(NetRuleKey) != $(KeyNull)
 else
 goto fatalregistry
 endif

 CloseRegKey $(NetRules)
 CloseRegKey $(NetworkCardKey)
 else
 goto fatalregistry
 endif
 OpenRegKey $(!REG_H_LOCAL) "" +
 $(!NTN_ServiceBase)"\"$(ServiceName) +
 $(MAXIMUM_ALLOWED) ServiceKey

 Ifstr(i) $(ServiceKey) != $(KeyNull)
 CloseRegKey $(ServiceKey)
 else
 goto fatalregistry
 endif
 endif

 goto end

successful = +
 goto end

abandon = +
 ForListDo $(OEM_ABANDON_OPTIONS)
 Shell $(UtilityInf), RemoveHardwareComponent, $(Manufacturer), +
 $(ProductSoftwareName), $($)
 ifint $($ShellCode) != $(!SHELL_CODE_OK)
 Debug-Output "ShellCode error"
 goto ShellCodeError
 endif

 set RegistryErrorIndex = $($R0)

 Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
 goto fatalregistry
 endif
 EndForListDo

 Ifstr(i) $(OEM_ABANDON_SOFTWARE) == TRUE

Shell $(UtilityInf), RemoveSoftwareComponent, $(Manufacturer), +
 $(ProductSoftwareName), FALSE
 ifint $($ShellCode) != $(!SHELL_CODE_OK)
 Debug-Output "ShellCode error"
 goto ShellCodeError
 endif

 set RegistryErrorIndex = $($R0)

 Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
 goto fatalregistry
 endif
 endif

 goto end

warning = +
 Shell $(subroutineinf) SetupMessage, $(!STF_LANGUAGE), "WARNING", $(Error)
 ifint $($ShellCode) != $(!SHELL_CODE_OK)
 goto ShellCodeError
 endif
 ifstr(i) $($R1) == "OK"
 goto $(to)
 else-ifstr(i) $($R1) == "CANCEL"
 goto $(from)
 else
 goto "end"
 endif
nonfatalinfo = +
 Set Severity = STATUS
 Set CommonStatus = STATUS_USERCANCEL
 goto nonfatalmsg
nonfatal = +
 Set Severity = NONFATAL
 goto nonfatalmsg
nonfatalmsg = +
 ifstr(i) $(Error) == ""
 Set Severity = NONFATAL
 Shell $(UtilityInf) RegistryErrorString "SETUP_FAIL"
 ifint $($ShellCode) != $(!SHELL_CODE_OK)
 goto ShellCodeError
 endif
 set Error = $($R0)
 endif
 Shell $(subroutineinf) SetupMessage, $(!STF_LANGUAGE), $(Severity), $(Error)
 ifint $($ShellCode) != $(!SHELL_CODE_OK)
 goto ShellCodeError
 endif
 ifstr(i) $($R1) == "OK"
 goto $(from)
 else
 goto "end"
 endif

fatalregistry = +
 Shell $(UtilityInf) RegistryErrorString $(RegistryErrorIndex)
 ifint $($ShellCode) != $(!SHELL_CODE_OK)
 goto ShellCodeError
 endif
 set Error = $($R0)
 goto fatal
fataldetect = +
 Shell $(UtilityInf),RegistryErrorString,CANNOT_DETECT
 ifint $($ShellCode) != $(!SHELL_CODE_OK)
 Debug-Output "ShellCode error: cannot get an error string."
 goto ShellCodeError
 endif
 set Error = $($R0)
 Goto fatal
fatal = +
 ifstr(i) $(Error) == ""
 Shell $(UtilityInf) RegistryErrorString "SETUP_FAIL"
 ifint $($ShellCode) != $(!SHELL_CODE_OK)
 goto ShellCodeError
 endif
 set Error = $($R0)
 endif
 Shell $(subroutineinf) SetupMessage, $(!STF_LANGUAGE), "FATAL", $(Error)
 ifint $($ShellCode) != $(!SHELL_CODE_OK)
 goto ShellCodeError
 endif

 goto setfailed

ShellCodeError = +
 set DlgType = "MessageBox"
 set STF_MB_TITLE = $(ShellCodeErrorTitle)
 set STF_MB_TEXT = $(ShellCodeErrorText)
 set STF_MB_TYPE = 1
 set STF_MB_ICON = 3
 set STF_MB_DEF = 1
 ui start "Error Message"
 goto setfailed

setfailed = +
 set CommonStatus = STATUS_FAILED
 ifstr(i) $(OEM_ABANDON_ON) == TRUE
 set OEM_ABANDON_ON = FALSE
 goto abandon
 endif
 goto end

end = +
 goto term

term = +

 Return $(CommonStatus)

[DebugConfiguration]

 Set InfName = "OEMSETNT.INF"

return


[Install-Option]
 set STF_VITAL = ""

 ifstr(i) $(AddCopy) == "YES"

  AddSectionFilesToCopyList Files-$(NDIS_VER) $(SrcDir)  $(!STF_WINDOWSSYSPATH)\drivers

  ifstr(i) (*($(CurrentVersionValue),4)) != $(NT400VersionConstant)
    AddSectionFilesToCopyList Files-SERIAL $(SrcDir) $(!STF_WINDOWSSYSPATH)\drivers
  endif

 endif

 ifstr(i) $(DoCopy) == "YES"

 set !STF_NCPA_FLUSH_COPYLIST = TRUE
 CopyFilesInCopyList

 endif

 Exit


[Install-Update]
 set STF_VITAL = ""
 set STF_OVERWRITE = "VERIFYSOURCEOLDER"

 AddSectionFilesToCopyList Files-3nicdiag $(SrcDir)win32 $(!STF_WINDOWSSYSPATH)
 AddSectionFilesToCopyList Files-HwDll $(SrcDir)WINNT $(!STF_WINDOWSSYSPATH)
 AddSectionFilesToCopyList Files-$(NDIS_VER) $(SrcDir) $(!STF_WINDOWSSYSPATH)\drivers
 AddSectionFilesToCopyList Files-SERIAL $(SrcDir) $(!STF_WINDOWSSYSPATH)\drivers
 AddSectionFilesToCopyList Files-Inf $(SrcDir) $(!STF_WINDOWSSYSPATH)

 set !STF_NCPA_FLUSH_COPYLIST = TRUE
 CopyFilesInCopyList

 exit



[Install-Dll]
 set STF_VITAL	= ""
 AddSectionFilesToCopyList Files-Dll $(SrcDir) $(!STF_WINDOWSSYSPATH)
 set !STF_NCPA_FLUSH_COPYLIST = TRUE
 CopyFilesInCopyList
 exit

[Install-3nicdiag]
 set STF_VITAL = ""
 AddSectionFilesToCopyList Files-3nicdiag $(SrcDir)win32 $(!STF_WINDOWSSYSPATH)
 AddSectionFilesToCopyList Files-HwDll $(SrcDir)WINNT $(!STF_WINDOWSSYSPATH)
 set !STF_NCPA_FLUSH_COPYLIST = TRUE
 CopyFilesInCopyList
 Exit

[Install-TrayAndCpl]
 set STF_VITAL = ""
 AddSectionFilesToCopyList Files-TrayAndCpl $(SrcDir)win32 $(!STF_WINDOWSSYSPATH)
 set !STF_NCPA_FLUSH_COPYLIST = TRUE
 CopyFilesInCopyList
 Exit

[Source Media Descriptions]
 1 = "Windows NT Setup Disk #1"
 2 = "3Com FEM556-TX Fast EtherLink PC Card Installation Disk"

[ProductType]
STF_PRODUCT = Winnt
STF_PLATFORM = I386

[Files-Inf]
2, OEMSETNT.INF, SIZE=60000,	RENAME=$(!UG_Filename)

[Files-Dll]
2, EL3C556.DLL, SIZE=50000

[Files-3nicdiag]
2,wnicdiag.exe, SIZE=300000
2,wnicdiag.hlp, SIZE=50000
2,wvaraddr.txt, SIZE=1000
2,un3c556.exe, SIZE=100000

[Files-HwDll]
2,hwaccess.dll, SIZE=90000
2,pcomdrv.sys, SIZE=9000
2,wc556cfg.dll, SIZE=90000

[Files-TrayAndCpl]
2,comsmd.exe, SIZE=10000

[Files-NDIS4]
2,FEM556N4.SYS , SIZE=60000

[Files-NDIS3]
2,FEM556N3.SYS , SIZE=60000

[Files-SERIAL]
2,SERIAL3.SYS , SIZE=60000

[LanguagesSupported]
 ENG

[AllFileConstantsENG]
ProCaption = "Windows NT Setup"
ProCancel = "Cancel"
ProCancelMsg = "Windows NT Networking is not correctly installed. "+
 "Are you sure you want to cancel copying files?"
ProCancelCap = "Network Setup Message"
ProText1 = "Copying:"
ProText2 = "To:"
DialogDllName = "EL3C556.DLL"

[FileConstantsENG-FEM556]
FunctionTitle		= $(GenericAdapterName)" Setup"$(GenericInfVersion)
ProductSoftwareTitle = $(GenericDriverName)
ProductHardwareTitle = $(GenericAdapterName)
IRQList 		= ^(IRQChoices, 1)
IRQValues		= ^(IRQChoices, 2)
InterruptStyleValues = ^(InterruptStyleChoices, 2)
IOBaseAddrList		= ^(IOBaseAddrChoices, 1)
IOBaseAddrValues		= ^(IOBaseAddrChoices, 2)
ModemIOBaseAddressList	    = ^(ModemIOBaseChoices,1)
ModemIOBaseAddressValues    = ^(ModemIOBaseChoices,2)
MemoryAddrList		    = ^(MemoryAddrChoices,1)
MemoryAddrValues	    = ^(MemoryAddrChoices,2)
ComPortList		    = ^(ComPortChoices, 1)
ComPortValues		    = ^(ComPortChoices, 2)
;Vivek
ModemIrqList                = ^(ModemIrqChoices,1)
ModemIrqValues              = ^(ModemIrqChoices,2)
;Vivek

[DialogConstantsENG-FEM556]
Help = "&Help"
Exit = "Cancel"
OK = "OK"
HelpContext = ""
Continue = "Continue"
Cancel = "Cancel"

[FileDependentDlgENG-FEM556]
DlgType = "RadioCombination"
DlgTemplate = "EL3C556"
Caption = $(FunctionTitle)
HelpContext = $(!IDH_DB_OEMNADE2_INS)
CBOptionsGreyed = {}
NotifyFields = {NO, NO, NO, NO}
Combo1Label = "I/O Port:"
Combo2Label = "Interrupt:"
Combo3Label = "Memory:"
Combo4Label = "Com Port:"

Combo1List = $(IOBaseAddrList)
Combo1Out = $(IOBaseAddrValue)
Combo2List = $(IRQList)
Combo2Out = $(IRQValue)
Combo3List = $(MemoryAddrList)
Combo3Out  = $(MemoryAddrValue)
Combo4List = $(ComPortList)
Combo4Out  = $(ComPortValue)
Combo5List = $(IRQList)
Combo5Out = $(ModemInterruptNumberValue)

ComboListItemsIn = {Combo1List,Combo2List,Combo3List,Combo4List,Combo5List}
ComboListItemsOut = {Combo1Out,Combo2Out,Combo3Out,Combo4Out,Combo5Out}

EditTextIn = {"",""}
EditTextLim = {"",""}

[MemoryAddrChoices]
;Vivek
MA_0 = "Auto", 0
;Vivek
MA_1  = "0xC8000", 819200
MA_2  = "0xC9000", 823296
MA_3  = "0xCA000", 827392
MA_4  = "0xCB000", 831488
MA_5  = "0xCC000", 835584
MA_6  = "0xCD000", 839680
MA_7  = "0xCE000", 843776
MA_8  = "0xCF000", 847872
MA_9  = "0xD0000", 851968
MA_10 = "0xD1000", 856064
MA_11 = "0xD2000", 860160
MA_12 = "0xD3000", 864256
MA_13 = "0xD4000", 868352
MA_14 = "0xD5000", 872448
MA_15 = "0xD6000", 876544
MA_16 = "0xD7000", 880640
MA_17 = "0xD8000", 884736
MA_18 = "0xD9000", 888832
MA_19 = "0xDA000", 892928
MA_20 = "0xDB000", 897024
MA_21 = "0xDC000", 901120
MA_22 = "0xDD000", 905216
MA_23 = "0xDE000", 909312
MA_24 = "0xDF000", 913408
MA_25 = "0xE0000", 917504
MA_26 = "0xE1000", 921600
MA_27 = "0xE2000", 925696
MA_28 = "0xE3000", 929792
MA_29 = "0xE4000", 933888
MA_30 = "0xE5000", 937984
MA_31 = "0xE6000", 942080
MA_32 = "0xE7000", 946176
MA_33 = "0xE8000", 950272
MA_34 = "0xE9000", 954368
MA_35 = "0xEA000", 958464
MA_36 = "0xEB000", 962560
MA_37 = "0xEC000", 966656
MA_38 = "0xED000", 970752
MA_39 = "0xEE000", 974848
MA_40 = "0xEF000", 978944

;Vivek
[ModemIrqChoices]
MdmIrq_1 = "4",4
MdmIrq_2 = "3",3
MdmIrq_3 = "4",4
MdmIrq_4 = "3",3
;Vivek

[ComPortChoices]
CP_1 = "COM1", 1
CP_2 = "COM2", 2
CP_3 = "COM3", 3
CP_4 = "COM4", 4

[ModemIOBaseChoices]
MdmIOBase_1 = "0x3F8",1016
MdmIOBase_2 = "0x2F8",760
MdmIOBase_3 = "0x3E8",1000
MdmIOBase_4 = "0x2E8",744

[MediaTypeChoices]
MT_1 = "TP (10BaseT)", 0
MT_2 = "COAX (10Base2)", 1

[IRQChoices]
;Vivek
IRQ_0 = "Auto",0
;Vivek
IRQ_1 = "3",3
IRQ_2 = "5",5
IRQ_3 = "7",7
IRQ_4 = "9",9
IRQ_5 = "10",10
IRQ_6 = "11",11
IRQ_7 = "12",12
IRQ_8 = "15",15

[IOBaseAddrChoices]
;Vivek
IOBase_0 = "Auto",0
;Vivek
IOBase_1 = "0x300",768
IOBase_2 = "0x200",512
IOBase_3 = "0x210",528
IOBase_4 = "0x220",544
IOBase_5 = "0x230",560
IOBase_6 = "0x1E0",480
IOBase_7 = "0x250",592
IOBase_8 = "0x260",608
IOBase_9 = "0x270",624
IOBase_10 = "0x280",640
IOBase_11 = "0x290",656
IOBase_12 = "0x2A0",672
IOBase_13 = "0x2B0",688
IOBase_14 = "0x2C0",704
IOBase_15 = "0x2D0",720
IOBase_16 = "0x2E0",736
IOBase_17 = "0x2F0",752
IOBase_18 = "0x310",784
IOBase_19 = "0x320",800
IOBase_20 = "0x330",816
IOBase_21 = "0x340",832
IOBase_22 = "0x350",848
IOBase_23 = "0x360",864
IOBase_24 = "0x370",880
IOBase_25 = "0x380",896
IOBase_26 = "0x390",912
IOBase_27 = "0x3A0",928
IOBase_28 = "0x3B0",944
IOBase_29 = "0x3C0",960
IOBase_30 = "0x3D0",976
IOBase_31 = "0x1F0",496
IOBase_32 = "0x3F0",1008

; -------------------------- BEGIN FORCE FIX - Vivek
[install-update-modem-info]

        OpenRegKey $(!REG_H_LOCAL) "" $(ZZZComPort) $(MAXIMUM_ALLOWED) +
                ZZZHandle

        ifstr $(ZZZHandle) == $(KeyNull)
                Debug-Output "<DBG: FORCE> OpenRegKey "$(ZZZComPort)" failed"
                goto done_update_modem_info
        endif

        Debug-Output "<DBG: FORCE> GetRegValue DosDevices"
        GetRegValue $(ZZZHandle) "DosDevices" DosDevicesValue
        set DosDevicesValueType = *($(DosDevicesValue), 3)
        set DosDevicesValueData = *($(DosDevicesValue), 4)
        ifint $(DosDevicesValueType) != $(!REG_VT_SZ)
                Debug-Output +
                "<DBG: FORCE> Bad DosDevices "$(ZZZComPort)" "$(DosDevicesValue)
                goto done_update_modem_info
        endif

        GetRegValue $(ZZZHandle) "PortAddress" PortAddressValue
        set PortAddressValueType = *($(PortAddressValue), 3)
        set PortAddressValueData = *($(PortAddressValue), 4)
        ifint $(PortAddressValueType) != $(!REG_VT_DWORD)
                Debug-Output +
                "<DBG: FORCE> Bad PortAddress "$(ZZZComPort)" "$(PortAddressValue)
                goto done_update_modem_info
        endif

        GetRegValue $(ZZZHandle) "Interrupt" InterruptValue
        set InterruptValueType = *($(InterruptValue), 3)
        set InterruptValueData = *($(InterruptValue), 4)
        ifint $(InterruptValueType) != $(!REG_VT_DWORD)
                Debug-Output +
                "<DBG: FORCE> Bad Interrupt "$(ZZZComPort)" "$(InterruptValue)
                goto done_update_modem_info
        endif

        ; now update the correct modem info

        Debug-Output +
        "<DBG: FORCE> "$(DosDevicesValueData)": iobase = "$(PortAddressValueData)", irq = "$(InterruptValueData)

        ifstr(i) $(DosDevicesValueData) == "COM1"
                set comNumber = 1
        else-ifstr(i) $(DosDevicesValueData) == "COM2"
                set comNumber = 2
        else-ifstr(i) $(DosDevicesValueData) == "COM3"
                set comNumber = 3
        else-ifstr(i) $(DosDevicesValueData) == "COM4"
                set comNumber = 4
        else
                goto done_update_modem_info
        endif


        set-dectohex PortAddressValueDataHex = $(PortAddressValueData)
        set-dectohex InterruptValueDataHex = $(InterruptValueData)

        Debug-Output +
        "<DBG: FORCE> PortAddressValueDataHex = "$(PortAddressValueData)
        Debug-Output +
        "<DBG: FORCE> InterruptValueDataHex = "$(InterruptValueData)

        ;
        ; Change ModemIOBaseAddressValues
        ;
        set oldList = $(ModemIOBaseAddressValues)
        set itemNumberToReplace = $(comNumber)
        set newData = $(PortAddressValueData)
        set return_addr = replace_modem_io_base
        goto replace_list_item
replace_modem_io_base = +
        set ModemIOBaseAddressValues = $(newList)

        ;
        ; Change ModemIOBaseAddressList
        ;
        set oldList = $(ModemIOBaseAddressList)
        set itemNumberToReplace = $(comNumber)
        set newData = $(PortAddressValueDataHex)
        set return_addr = replace_modem_io_base_list
        goto replace_list_item
replace_modem_io_base_list = +
        set ModemIOBaseAddressList = $(newList)

        ;
        ; Change ModemIrqValues
        ;
        set oldList = $(ModemIrqValues)
        set itemNumberToReplace = $(comNumber)
        set newData = $(InterruptValueData)
        set return_addr = replace_modem_irq
        goto replace_list_item
replace_modem_irq = +
        set ModemIrqValues = $(newList)

        ;
        ; Change ModemIrqList
        ;
        set oldList = $(ModemIrqList)
        set itemNumberToReplace = $(comNumber)
        set newData = $(InterruptValueDataHex)
        set return_addr = replace_modem_irq_list
        goto replace_list_item
replace_modem_irq_list = +
        set ModemIrqList = $(newList)



done_update_modem_info = +
        ifstr $(ZZZHandle) != $(KeyNull)
                CloseRegKey $(ZZZHandle)
        endif
        exit

replace_list_item = +
        ;
        ; INPUT: needs the following variables to be initialized
        ;       - oldList
        ;       - itemNumberToReplace
        ;       - newData
        ;       - return_addr (i.e. label to jump back to)
        ; OUTPUT: returns with the newList initialized
        ;

        ;Debug-Output "<DBG: FORCE> Replacing item number "$(itemNumberToReplace)" in the list "$(oldList)" with the data "$(newData)

        set newList = {}
        ForListDo $(oldList)
                ifint $(#) == $(itemNumberToReplace)
                        set newList = >($(newList), $(newData))
                else
                        set newList = >($(newList), $($))
                endif
        EndForListDo
        goto $(return_addr)



  ;-------------------------- END FORCE FIX 
Download Driver Pack

How To Update Drivers Manually

After your driver has been downloaded, follow these simple steps to install it.

  • Expand the archive file (if the download file is in zip or rar format).

  • If the expanded file has an .exe extension, double click it and follow the installation instructions.

  • Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.

  • Find the device and model you want to update in the device list.

  • Double-click on it to open the Properties dialog box.

  • From the Properties dialog box, select the Driver tab.

  • Click the Update Driver button, then follow the instructions.

Very important: You must reboot your system to ensure that any driver updates have taken effect.

For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.

server: web4, load: 1.05