Mouse User's Manual 1994-2001 Copyright All Rights Reserved FCC Statement on CLASS B Note: This equipment has been tested and found to comply with the limits for a CLASS B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. if this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: * Reorient or relocate the receiving antenna. * Increase the separation between the equipment and receiver. * Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. * Consult the dealer or an experienced radio TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference. (2) this device must accept any interference received, including interference that may cause undesired operation. 1. Hardware Installation 1-1.Installing a Serial Mouse You must have a PC fitted with a serial port(COM1/COM2) in order to install the mouse. Plug your mouse into the serial port. 1-2.Installing a Mouse with Mouse Port (PS/2) Connector If you have a mouse with a round mouse port connector, you must turn off the computer before connecting or disconnecting your mouse. 1-3.Installing a Combo Mouse The Combo Mouse comes with a PS/2 (DIN 6) cable connector, together with a PS/2 -> Serial (COM 9) port adapter. Before plug your mouse into the computer, try to make sure what kind of mouse port you have. If you have a PS/2 port, plug in the original PS/2 cable connector; if you have a Serial port, please connect the adapter first to the cable, then plug into the Serial port. 1. Turn the computer off. 2. Locate an available 6-pin round port on your computer. 3. Insert the mouse connector into the round mouse port. 4. Start your computer. 1-4.Select and Set ID for Wireless Mouse Plug in receiver connector to your computer to turn on LED indicator. After pressing ID setting button at the bottom of receiver, the LED lighting flashed, and it's ready for your further mouse ID setting: Set one mouse ID out of four: ID one: Press the ID defining button (at the mouse bottom) ID two: Press command key and ID defining button simultaneously ID three: Press Pup-up key and ID defining button simultaneously ID four: Press wheel button and ID defining button simultaneously After you select ID and send signal from mouse, the mouse receiver will receive and automatically detect and correspond to mouse for the working linkage.After you successfully finish ID setting, the LED indicator of receiver is corresponding to every move of the working mouse by confirming of lighting flash. If you want to re-define the ID, you have to press ID setting button first at the receiver bottom. Then, process mouse ID setting again. *Please note: once you change the batteries, you will have to re-define the ID as well. 2. Mouse Driver Installation Mouse software supports Windows 95, Windows 98, Windows ME, Windows NT 4.0, and Windows 2000. Before installing any software under Windows NT 4.0, we strongly recommend you create an Emergency Repair Disk using the Repair Disk utility provided by the system (RDISK.EXE). Please note that USB mice are only supported under Windows 98, Windows ME and Windows 2000. Run Setup.exe to install the Mouse software. 3. Uninstall Program Mouse Software can be removed from Windows by clicking the Add/Remove Programs icon in the Control Panel or clicking the "Uninstall" icon in the folder that setup.exe created in "Programs" of "Start" button on Windows desktop. Select Mouse Software installed and click the "Remove" button. 4. Switching Mouse Mode 4-1.Switching Mouse Hareware Modes (Use mode switch) The Serial Mouse is capable of operating either as a Microsoft Serial Mouse or a Mouse Systems Mouse. At the base of the Mouse you will find a slide switch. The switch has two possible positions, 'MS' and 'PC' When the switch is set to the 'MS' position the Mouse will emulate a two-buttoned Microsoft Mouse while setting the switch to the 'PC' position will cause the Mouse to emulate a three-buttoned Mouse Systems Mouse. 4-2.Switching Mouse Hardware Modes (None mode switch) As mentioned earlier, the serial mouse is capable of operating either as a Microsoft Serial Mouse or a Mouse Systems Mouse. Which of the two modes the mouse will operate in is determined on the power-on initialization. If any one of the three buttons is depressed during power-on initializa- tion, the mouse will emulate Mouse Systems Mouse. While none of the buttons is depressed during power-on initiation the mouse will emulate Microsoft Mouse. 4-3.Microsoft Mode When the mouse is in Microsoft mode, only the left and right buttons are active, while the middle button is ignored. In this mode, your mouse will correctly emulate a Microsoft Serial Mouse. 4-4.Mouse Systems Mode If you are a user of AUTOCAD or any other software which gives enhanced performance with a Mouse Systems Mouse you should choose this emulation. A Mouse Systems Mouse operates with all three buttons. Note: Because Windows 95 and Windows NT supports serial 'MS' mouse mode, you had better switch the mouse to 'MS' mode when first install the mouse driver in package. After completing the installation, you can switch to 'PC' mouse mode when restart the computer. 5. Trouble Shooting Symptom 1 : No mouse movement. Solution : - Make sure the software that you are using supports a mouse. - Check that mouse is plugged into serial port at the back of computer. - Ensure that mouse driver is installed into system. Symptom 2 : The cursor on the screen remains at one spot or moves erratically. Solution : Check the mouse cable for any breaks or sharp twists. Examine the cable closely where it connects to the mouse. Symptom 3 : The cursor movement stops at a corner and no longer responds to the mouse movement. Solution : Run the mouse driver to check which mode the mouse is operating in. Symptom 4 : Mouse movement does not produce corresponding cursor movement or there is a brief pause during movement. Solution : Clean the silicon rubber-coated ball and rollers. Symptom 5 : After had selected mouse type for Windows 95 ,the mouse would be disable when you clicked "OK" . Solution : Using keyboard to close the current window and wait for Windows 95 to give any instruction to restart your computer. After restart Windows 95 the mouse will work normally. Symptom 6 : Displayed error number -115 on screen when install mouse driver software. Solution : The error usually occurs because a virus-checking program is being used on the System to prevent files from being renamed. Please shutdown any virus checking software running on the system and then run the setup again. Symptom 7 : Detection Problems with PS/2 Pointing Devices Solution : If your mouse is connected to the mouse port and is not detected by the system, attempt the following step(s): 1) Your mouse port might need to be enabled through the SETUP menu of your computer. Please check your computer documentation regarding the SETUP menu. 2) If you have a mouse with both serial and mouse port adaptors, connect the mouse to the computer through the serial port. Reboot and check if the mouse is detected properly. 3) If adaptor(s) were not included in your package, your mouse was designed to work on only one type of port (Serial OR PS/2). Refer to your package for the type of port your mouse supports. If the problem persists, please check for a possible computer BIOS ROM upgrade from your computer manufacturer. Some notebook systems, such as IBM Thinkpad, have both an external Mouse Port and an integrated Pointing Stick, which is connected to the Mouse Port. If your mouse is having difficulty running on the Mouse Port of this type of system, try using the serial port instead. Symptom 8 : Conflicts with other Serial Devices Solution : Some softwares provided by other manufacturers with mouse functions, such as Logitech MouseWare, which may conflict with this mouse. Recommended strongly to remove the software installed previously before install this mouse software. Symptom 9 : Problems Operating the Wheel Solution : If your mouse is equipped with a wheel and the wheel does not scroll, verify the following: 1) Verify that the "Browser Mouse" or "Mouse Control Panel" application is installed properly. If you do not find the "Browser Mouse" or "Mouse Control Panel" icon in the system tray, you need to reinstall mouse software. 2) Some other applications with mouse scrolling function may conflict with this mouse function. Remove these applications before install this mouse software.Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.