ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ» º º º Compex RE100TX 10/100 PCI Fast Ethernet Adapter º º (C) Copyright PDS, 1999. All Rights Reserved. º º º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ¼ ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³ GENERAL INFORMATION ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ 1) DOS and OS/2 NDIS v2.01 device driver RE100.DOS and RE100.OS2 The NDIS drivers for OS/2 and DOS were written to and tested with the Network Driver Interface Specification (NDIS) Version 2.0.1. ** IMPORTANT: ========== If you loading EMM386.EXE v4.49 ensure to exclude memory range D000-DFFF e.g. add this statement in Config.sys, Device=C:\DOS622\EMM386.EXE noems x=d000-dfff The file layout in the MSLANMAN.DOS and MSLANMAN>OS2 directories is shown below:- MSLANMAN.DOS ³ ÀÄÄ DRIVERS ³ ÃÄÄÄ ETHERNET ³ ³ ³ ÀÄÄÄ RE100 ³ ³ ³ ÃÄÄ RE100.DOS ³ ÀÄÄ PROTOCOL.INI ³ ÀÄÄÄ NIF ³ ÀÄÄÄÄÄ RE100.NIF MSLANMAN.OS2 ³ ÀÄÄ DRIVERS ³ ÃÄÄÄ ETHERNET ³ ³ ³ ÀÄÄÄ RE100 ³ ³ ³ ÃÄÄ RE100.OS2 ³ ÀÄÄ PROTOCOL.INI ³ ÀÄÄÄ NIF ³ ÀÄÄÄÄÄ RE100.NIF ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³ INSTALLATION GUIDE ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ 1) LAN Manager 2.0 ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ a) Start the SETUP program. b) Choose "Actions" from the top manual bar. c) Choose "Import network drivers" to load the driver. Insert the driver diskette into a drive and enter correct source drive letter. Then SETUP will create the appropriate directory and transfer the driver from the diskette. After this step, the driver is loaded. If you want to change the existing driver, then you should go through the following steps: d) Choose "View/Modify" from the top manual bar. e) Press [ENTER] until you find the "Network Drivers" manual. In this manual, you will find the existing network driver configuration and all network adapters and protocols which it supports. f) Remove the existing configuration by choosing "Remove". g) Select "Compex RE100TX 10/100Base-TX PCI Ethernet Adapter" in the "Network adapter card" box and choose the appropriate protocol layer in the "Protocol" box. h) Choose "Add Driver" to add a hardware driver and "Add Protocol" to add a protocol driver to the "Network Configuration" box. i) Then choose "Done" to exit to the main manual. j) Before exiting the SETUP program, choose "Save" from the "Actions" box to update the changes you have made. 2) LAN Manager 2.1/2.2 ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ The setup procedures for LAN Manager 2.1 is similar to LAN Manager 2.0. Follow the procedure listed below to perform your installation. a) Start the SETUP program. b) Choose "Configuration" from the top manual bar. c) Choose "Network Drivers" to enter to the "Workstation Configuration" box. d) Choose "Add New Config" to check the existing network adapter drivers. e) Select "Other Driver" to import the driver from the diskette. Insert the driver diskette into a drive and enter correct source drive letter. Then SETUP will create the appropriate directory and transfer the driver from the diskette. Parameters supported: "*" indicate default value MEDIUM = AUTO Other option AUTO, 10HALF, 10FULL, 100HALF, 100FULL This parameter force the card to a specific media connect mode. Default is N-Way auto-negotiation NETADDRESS= xxxxxxxxxxxx where xxxxxxxxxxxx are hex numbers value in hex This parameter overrides the network address of the network adapter card. The value of this parameter is a hexadecimal string of 13 digits, as in @008048nnnnnn. The address must be unique among all other network adapter addresses on the network." ETHERID = xxxxxxxxxxxx where xxxxxxxxxxxx are hex numbers value in hex This parameter using multiple network adapter card. The value of this parameter is a hexadecimal string of 13 digits, as in @008048nnnnnn. The address must be unique among all other network adapter addresses on the network." BUSNO = 0 range is 0-31 value in decimal This parameter is the PCI BUS number to combined this adapter card. The value of this parameter is 0-31" DEVICENO = 0 range is 0-255 value in decimal This parameter is the PCI DEVICE number to combined this adapter card. The value of this parameter is 0-255." TXFIFO = 0 range is 0-63 value in decimal Specifies the early transmit threshold level in the Tx FiFo begin the transmission. The value of this parameter is 0-63 "Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.