ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ» º º º Compex RE100TX 10/100 PCI Fast Ethernet Adapter º º (C) Copyright PDS, 1999. All Rights Reserved. º º º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ¼ ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³ GENERAL INFORMATION ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ The 16-bit NDIS 2.01 driver for IBM LAN Server OS/2 servers/clients is located in the \NDIS2\OS2 directory. \NDIS2\OS2\RE100.OS2 - 16-bit NDIS 2.01 for OS/2 IBM LAN Server also requires a unique NIF file. \NDIS2\RE100.NIF - NIF file for IBM OS/2 Server and Requester ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³ INSTALLATION GUIDE ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ To install the Compex RE100TX 10/100 PCI Fast Ethernet NDIS 2.01 driver, follow the instructions below: Installation of IBM OS/2 Warp Connect in OS/2 Warp 3.0 ====================================================== The procedure assumes you are using CD-ROM in the installation. Drive D is the CD device. 1. Start up OS/2 Warp in the PC. 2. Open the OS/2 System Windows and click "OS/2 Warp Connect Install/Remove" icon. 3. Click the "Select Warp Connect Selective Install for Networking" icon. 4. The "OS/2 Warp Connect" and "Local versus Remote" dialog boxes appear. Select "On this workstation" option fron Local versus Remote box and click OK button. 5. Select "Advanced Installation" option from Installing OS/2 Warp Connect dialog box and click OK button to continue. 6. The "Product Selection" dialog box appears, select "IBM client porducts" option and click OK button. 7. When the "Set up selected products" box appears, click "Other adapter..." button to install Compex RE100TX 10/100 PCI NDIS 2 driver. 8. When prompted, insert the Compex RE100TX 10/100 PCI driver disk in drive A and enter the drive name and path to the RE100.NIF file. Click OK. e.g. A:\NDIS2\OS2 The Compex RE100TX 10/100 PCI Ethernet Adapter name will be displayed in the "Driver Found" box of LAN adapters list. 8. The "Compex RE100TX 10/100 PCI Ethernet Adapter" option will be highlighted. Select "Ethernet" in Type of LAN option. Click OK. 9. When the "Set up selected products" box appears again, click "Settings" button to configure the network adapter parameters. 10. Click OK again to confirm the selected parameters. 10. Click "Install" button to continue installing until it completes. 11. Reboot the station. The RE100TX adapter is now ready to run. Installation of IBM OS/2 LAN Server/Requester 4.0 in OS/2 Warp 3.0 =================================================================== NOTE:- Installation of Server and Requester steps are the same for network cards. Only Requester installation steps are described below. The procedure assumes you are using CD-ROM in the installation. Drive D is the CD device. 1. Start up OS/2 Warp in the PC. 2. Open an OS/2 Windows, change to drive D:\ and run INSTALL. 3. Select the service "IBM OS/2 LAN Requester" 4. Enter a unique name for the requester station. 5. Enter the domain name of the network domain server. 6. When "Select Network Adapter" window appear, click "Other adapters" button below the window. 7. When prompted, insert the Compex RE100TX 10/100 PCI driver disk in drive A and enter the drive name and path to the RE100.NIF file. Click OK. e.g. A:\NDIS2\OS2 The Compex RE100TX 10/100 PCI Ethernet Adapter name will be added to the " Select Network Adapter " box of LAN adapters list. 8. From the list select "Compex RE100TX 10/100 PCI Fast Ethernet Adapter". Click OK. 9. Click OK again to confirm the selected adapter is the correct one. 10. The installation program will then contiune to run until it completes. 11. Reboot the station. The RE100TX adapter is now ready to run. Installation Procedure for installing IBM LAN Server OS/2 Server/Requester ========================================================================== Please note that the instsallation procedure described below is based on the IBM LAN Adapter and Protocol Support program that comes with IBM LAN Server ver 3.0. For the other versions of LAN Adapter and Protocol Support program, please refer to its "Installation Guide" for details. 1. Boot up IBM OS/2 and run IBM LAPS program. a) Make sure the IBM OS/2 operating system is properly installed and functioning. Insert the IBM LAPS (LAN Adapter and Protocol Support) disk into the floppy disk drive). In IBM OS/2, select to run LAPS program. Please refer to the "IBM LAN Adapter and Protocol Support Configuration Guide" for more information about this utility. b) From the IBM LAPS main dialog box, select 'INSTALL' button. If the LAPS program has been installed on your system, it will start installing and configurign the network drivers into your system. Go to step 2 now and continue. c) If the LAPS program hasn't been installed on your system yet, the target drive dialog box will appear on the screen. Specify target drive where you want the LAPS program to be installed (eg. drive 'C') now and select 'OK' button. d) The LAPS program begins to transfer files from the floppy disks to the target drive specified in the above step. When it finishes, select 'OK' button and it will return to the LAPS main dialog box. Now, you have to select 'INSTALL' button again to install and configure the driver of Compex LAN card into IBM LAN Server environment. 2. Install NDIS 2.01 driver into the system. Insert the Compex RE100TX 10/100 PCI Driver Disk into the floppy drive (eg. drive A). Type "A:\NDIS2\OS2" at the prompt where it asks you for the source of driver and INF files and then select 'OK' button. The LAPS program will copy the appropriate driver file and INF file from the Driver Disk and then it will return to the main dialog box. 3. Configure network drivers. a) From the main dialog box, select 'Configure' button. b) In the 'Configuration' dialog box, choose the 'Configure LAN Transport' option and select 'Continue' button. c) When 'Configure Workstation' dialog box shows up, choose "Compex RE100TX 10/100 PCI Ethernet Adapter" from the 'Network Adapters' list box by highlighting that entry. Then choose 'Add' to add the Compex LAN card to the 'Current Configuration' list box. d) Highlighting the appropriate protocols in the 'Protocols' list box. Then choose 'Add' to add them to the 'Current Configuration' list box. e) If you want to edit the card's configuration, choose 'Compex RE100TX 10/100 PCI Ethernet Adapter' and then choose 'Edit'. After the editing is done, select the 'OK' button to return to the 'Configure Workstation' screen. f) Select 'OK' button if all the configuration has been done and LAPS program will return to the main dialog box. g) Select 'Exit' button to indicate the completion of configuration and then follow the instructions on the screen or refer to the "LAPS Installation Guide" to complete the installation process of LAPS. The LAPS program will update your CONFIG.SYS file in the IBM OS/2 boot disk and then return to OS/2 prompt. 4. Install IBM LAN Server software or IBM LAN Server OS/2 Requester software. Refer to the installation guide for IBM OS/2 LAN Server or OS/2 Requester and follow the instructions to complete the rest of server/requester program installation. 5. Reboot the computer. All the changes made to your computer will not take effect until you reboot the computer.Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.