****************************************************************************
* *
* Plug & Play Ethernet Card *
* *
* NDIS Driver for Windows for Workgroups 3.11 *
* *
* README file *
* *
****************************************************************************
1. Introduction:
These Ethernet drivers for Windows for Workgroups 3.11 conform to 3Com/
Microsoft Network Driver Interface Specification v3.0. It supports Micro-
soft Windows for Workgroups v3.11 enviroment.
2. Contents of the Subdirectory:
PNPND.DOS The NDIS2 driver.
PNPND.386 The NDIS3 driver.
OEMSETUP.INF A setup-information file for installing the Ethernet
NDIS driver under Windows for Workgroups 3.11.
3. Installation
* Take the following steps at the first time you set up Windows for
Workgroups on your hard disk:
1) Select "Network Setup" from Windows Program Manager's Network group.
2) From the "Network Setup" window, select "Drivers..." button.
3) When the "Network Drivers" windows shows, choose "Add Adapter..."
button.
4) From the "Add Network Adapter" window, select "Unlisted or Updated
Network Adapter".
5) When the "Install Driver" window shows, insert the Ethernet Driver
Disk to any floppy, for example A:, and then enter "A:\WFW311" and
select OK.
6) From the "Unlisted or Updated Network Adapter" window, choose
"PNPND Ethernet Adapter".
7) After Windows for Workgroups has read the driver, the "PNPND Ether-
net Adapter" window will be displayed again.
8) From the "Network Drivers" window, select the "Close" button.
9) When returning to the "Network Setup" window , select "Continue".
* If the Windows for Workgroups has been installed and you want to change
the network adapter to PNPND Ethernet Adapter, follow the procedure
described below.
1) Select "Network Setup" from Windows Program Manager's Network group.
2) From the "Network Setup" window, select "Drivers...".
3) From the "Network Drivers" window, select "Add Adapter..." button.
4) From the "Add Network Adapter" window, select "Adapters".
5) From the "Network Adapters" window, select the "Remove" button to
discard the previous settings.
6) Select the "Add" button. When the "Add Network Adapter" window is
displayed, choose "Unlisted or Updated Network Adapter".
7) When the "Install Driver" window shows, insert the Ethernet Driver
Disk to any floppy, for example A:, and then enter "A:\WFW311" and
select OK.
8) When the "Unlisted Or Updated Network Adapter" window appears again,
choose "PNPND Ethernet Adapter".
9) After Windows for Workgroups has read the driver, the "PNPND Ether-
net Adapter" window will be redisplayed.
10) From the "Network Adapters" window, select the "Close" button.
11) When returning to the "Network Setup" window, select OK.
* Take the following steps at the first time you setup Windows for Work-
groups on your hard disk:
1) Select 'Network Setup' from Network group in Windows Program Manager.
2) When the "Network Setup" window appears, select 'Drivers...' botton.
3) When the 'Network Drivers' windows shows, choose 'Add Adapter...' bot-
ton.
4) When the 'Add Network Adapter' window is displayed, select 'Unlisted
or Updated Network Adapter'.
5) When the 'Install Driver' window appears, insert the Distribution
Diskette into drive A:, and then enter 'A:\WFW311' and select 'OK'.
7) When the 'Unlisted or Updated Network Adapter' window is displayed,
choose "PNP Ethernet Adapter".
8) After Windows for Workgroups has finished reading the driver, the
'PNP Ethernet Adapter' window will be re-displayed.
9) In the 'Network Drivers' window, select the 'Close' button.
10) After returning to the 'Network Setup' window , select 'Continue'.
* If the Windows for Workgroups has been installed and you want to change
the network adapter to PNP Ethernet Adapter, follow the produre de-
scribed below.
1) Select 'Network Setup' from Network group in Windows Program Manager.
2) In 'Network Setup' window, select 'Drivers...'.
3) In 'Network Drivers' window, select 'Add Adapter...' botton.
4) In the 'Add Network Adapter' window, select 'Adapters'.
5) In the 'Network Adapters' window, select the 'Remove' button to cancel
the previous settings.
6) Select the 'Add' button. When the 'Add Network Adapter' window is dis-
played, choose 'Unlisted or Updated Network Adapter'.
7) When the 'Install Driver' window appears, insert the Distribution Disk-
ette into drive A:, and then enter 'A:\WFW311' and select 'OK'.
8) When the 'Unlisted Or Updated Network Adapter' window is re-displayed,
choose 'PNP Ethernet Adapter'.
9) After Windows for Workgroups has read the Ethernet driver completely,
the 'PNP Ethernet Adapter' window will be re-displayed.
10) In the 'Network Adapters' window, select the 'Close' button.
11) After returning to the 'Network Setup' window, select 'OK'.
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.