README.TXT Driver File Contents (LAN.zip)

							     Jan. 1996
			DE-220 Ethernet Card Family
			     Setup/Diagnostic
		 =========================================

Copyright (c) 1995 by D-Link Corporation. All rights reserved.

ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ»
º Setup/Diagnostic program º
ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ

The SETUP.EXE program is a program for setting up the DE-220 Ethernet
adapters.  This program not only allows you to configure the adapters, but
also allows you to check the adapter functionality and link states.

To run this program, execute one of the following commands:

      SETUP
      SETUP /F
      SETUP /D

Run the setup program with the /F switch (SETUP /F) only if the card's EEPROM
data have been corrupted or if you experiencing any other difficulty when
running the program without the /F switch.

You can also configure the adapter in non-interactive mode by specifying the
/D switch (SETUP /D).  The SETUP program will load the configuration values
specified in  the SETUP.DAT text file.	This file can be found on the same
directory as  the SETUP.EXE program.

The following is a sample SETUP.DAT file:

   Connector Type	UTP	--------> This sets the media type
   I/O Base Address	0x300	--------> This sets the I/O base address
   Interrupt Number	5	--------> This sets the IRQ number
   ROM Size		16k	--------> This sets the boot ROM size
   ROM Address		0xD000	--------> This specifies the boot ROM address
   PNP			Enable	--------> This enables the PnP function

NOTES:
   1. The PnP function is only used with PnP-compliant adapters.
   2. SETUP/D only affects the parameters that are specified in the SETUP.DAT
      file; other configuration parameters will remain unchanged.
   3. If the SETUP.DAT file specifies any parameter settings related to the
      boot ROM, the boot ROM will be automatically enabled.  Otherwise,
      it is disabled.
   4. If the connector type is not specified, the driver will automatically
      detect the media port used in the network connection.

	 DE-220 Adapter Family parameter file table (SETUP.DAT)
	 ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
	 ³ KEYWORDS	  ³  AVAILABLE SELECTIONS	     ³
	 ÆÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍØÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ͵
	 ³ Interrupt	  ³  3, 4, 5, 9, 10, 11, 14, 15      ³
	 ³    number	  ³				     ³
	 ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
	 ³ I/O Base	  ³  300H, 320H, 340H, 360H	     ³
	 ³    Address	  ³				     ³
	 ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
	 ³ ROM Size	  ³  8K/16K/32K 		     ³
	 ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
	 ³ ROM Address	  ³  C000 C800 D000 D800	     ³
	 ³		  ³  C200 CA00 D200 DA00	     ³
	 ³		  ³  C400 CC00 D400 DC00	     ³
	 ³		  ³  C600 CE00 D600		     ³
	 ³		  ³  <Note>			     ³
	 ³		  ³  DC00 (Ethernet II frame type)   ³
	 ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ

	DE-220E Series Adapter parameter file table (SETUP.DAT)
	 ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
	 ³ KEYWORDS	  ³  AVAILABLE SELECTIONS	     ³
	 ÆÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍØÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ͵
	 ³ Connector Type ³  UTP, BNC, AUI		     ³
	 ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
	 ³ Interrupt	  ³  3, 4, 5, 9, 10, 11, 14	     ³
	 ³    Number	  ³				     ³
	 ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
	 ³ I/O Base	  ³  200H,220H,240H,260H,	     ³
	 ³    Address	  ³  300H,320H,340H,360H	     ³
	 ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
	 ³ ROM Size	  ³  8K/16K			     ³
	 ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
	 ³ ROM Address	  ³  C0000h C4000h C8000h CC000h,    ³
	 ³		  ³  D0000h,D4000h,D8000h,DC000h     ³
	 ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ

	DE-220P Series Adapter parameter file table (SETUP.DAT)
	 ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
	 ³ KEYWORDS	  ³  AVAILABLE SELECTIONS	     ³
	 ÆÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍØÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ͵
	 ³ Connector Type ³  UTP, BNC, AUI		     ³
	 ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
	 ³ Interrupt	  ³  3, 4, 5, 9, 10, 11, 12, 15      ³
	 ³	Number	  ³				     ³
	 ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
	 ³ I/O Base	  ³  200H,220H,240H,260H	     ³
	 ³    Address	  ³  280H,2A0H,2C0H,2E0H	     ³
	 ³		  ³  300H,320H,340H,360H	     ³
	 ³		  ³  380H,3A0H,3C0H,3E0H	     ³
	 ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
	 ³ ROM Size	  ³  8K/16K			     ³
	 ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
	 ³ PNP		  ³  Enable/Disable		     ³
	 ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
	 ³ ROM Address	  ³  C0000h C4000h C8000h CC000h,    ³
	 ³		  ³  D0000h,D4000h,D8000h,DC000h     ³
	 ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ

ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ»
º Information about the Setup Program º
ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ

1. The following lists the setup and diagnostic files:

   README.TXT	 : Contains information on the usage of the setup program
   SETUP.EXE	 : The Setup program
   DIAG.EXE	 : The diagnostic program
   FORCE.EXE	 : The forced setup program for PnP adapters
   IPXODI.COM	 : The IPX protocol driver for the ODI stack
   LSD.EXE	 : The Setup and diagnostic program
   NETDIAG.EXE	 : The network diagnostic program for PnP adapters
   LSL.COM	 : The link support layer for the ODI stack
   DE22X.COM	 : The ODI driver
   NET.CFG	 : The ODI configuration file
   SETUP_D.EXE	 : The SETUP /D program
   SETUP.DAT	 : The configuration data file

2. The Setup main menu provides four options:

   Auto Configuration
       - This option automatically configures your adapter, specifying values
	 for such parameters as connector type, I/O base address, IRQ and
	 remote boot function.	This however does not support  the PnP adapters.

   Setup Configuration
       - This option allows you to manually specify configuration values for
	 the adapter.

   Adapter Basic Diagnostics
       - This option performs a diagnostic test on the various adapter
	 components.

   Network Diagnostic
       - This option allows you to test the connectivity of the adapter on the
	 network.

3. Setup also lets you view the current adapter configuration, including:

     Viewed items: Your Current Configuration
		 <1> Node ID
		 <2> Bus Mode
		 <3> Card Type

     Viewed/Changed items: Setup Configuration
		 <1> Connector Type
		 <2> I/O Base Address
		 <3> Interrupt Number
		 <4> Remote Boot ROM Size/Base Memory Address

ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ»
º Detailed Description of Setup Programsº
ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ

The following displays the Setup main menu:

	ÉÍÍÍÍÍ	    Main Menu	 ÍÍÍÍÍÍ»
	º  Auto Setting Configuration  º
	º  Setup Configuration	       º
	º  Adapter Basic Diagnostics   º
	º  Network Diagnostics	       º
	ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ

   1. Select Auto Setting Configuration for automatic adapter configuration.
      The program will automatically select a working configuration for the
      adapter, including the connector type, I/O base address, interrupt number,
      and remote boot function.

   2. Select the Setup Configuration option to manually configure your adapter.
      Here you specify settings for connector type, I/O base address,
      interrupt number and whether or not to enable the remote boot function.

   3. The Adapter Basic Diagnostics option checks the major components of the
      adapter and cabling to ensure proper operation.

   4. Select Network Diagnostics to perform a live transmission test for
      checking the adapter's network connectivity. This test requires that
      LSL.COM, DE22X.COM and IPXODI.COM be located on the same directory as
      the Setup program.


Setup Configuration Menu
------------------------

	ÚÄÄÄÄÄÄÄÄÄ Setup Configuration ÄÄÄÄÄÄÄÄÄÄÄ¿
	³					  ³
	³ Connector Type ------> UTP (RJ-45)	  ³
	³ I/O Base Address ----> 300H		  ³
	³ Interrupt Number ----> 3		  ³
	³ Plug and Play -------> Disable	  ³
	³ Remote Boot ---------> Disable	  ³
	ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ

   1. The Connector Type field allows you to specify the adapter port that
      will be used in the network connection.

   2. The I/O Base Address field allows you to specify the I/O base address of
      the adapter.

   3. The Interrupt Number field lets you specify the adapter's IRQ number.

   4. The Plug and Play field allows you to enable or disable the PnP function
      of the adapter. This field only appears on PnP-compliant adapters.

   5.  The Remote Boot field allows you to use the remote boot function of the
       adapter. This however requires that you install a boot ROM chip on the
       provided socket on the adapter.

   6. The Boot ROM Address field allows you to specify the starting address of
      the boot ROM. This field only appears when the boot ROM function is
      enabled.

   7. The Boot ROM Size field specifies the boot ROM size.  This field only
      appears when the boot ROM function is enabled.

Adapter Basic Diagnostics
-------------------------

The Adapter Basic Diagnostics option allows you to perform a series of tests
on the adapter. These tests include:

   1. Current I/O Base Address
   2. DC-DC Convert, Oscillator, Crystal T7213
   3. EEPROM
   4. LAN Setup Registers
   5. Memory
   6. LAN Controller Functions
   7. Cable Connection
   8. Loopback Mode

   ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ Adapter Diagnostic ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ»
   º  Node Address     : 00 80 C8 00 00 00		    º
   º  I/O Base Address : 300H				    º
   º  Connector Type   : BNC (Thin Coax)		    º
   º  Interrupt Number : 15(16-bit)			    º
   ÇÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ Cycle      ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄĶ
   º  Current I/O Base Address ...................  Pass    º
   º  DC-DC Convert, Oscillator, Crystal T7213 ...  Pass    º
   º  EEPROM .....................................  Pass    º
   º  LAN Setup Registers ........................  Fail    º
   º  Memory .....................................  Unknown º
   º  LAN Controller Functions ...................  Unknown º
   º  Cable Connection ...........................  Unknown º
   º  Loopback Mode Testing ......................  Unknown º
   º							    º
   ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ

Network Diagnostics
-------------------

	ÉÍÍ Advanced Diagnostics ÍÍÍ»
	º Setup as a master station º
	º Setup as a slave station  º
	ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ

The Network Diagnostics option tests the ability of the adapter to communicate
with other stations on the network. This test requires setting up of one
master station and one slave station. The master station is responsible for
sending test packets to the network, while the slave station is responsible
for sending back these packets to the master station.  There is good
connectivity if all the packets sent by the master were able to come back.

To set up a station as master, select "Setup as a master station".  To set up
the other station as slave, select "Setup as a slave station".

Before running this test though, ensure to copy first LSL.COM, IPXODI.COM,
DE22X.COM and NET.CFG to the same directory where the Setup program resides.
Also, ensure that the slave and master stations use the same frame type
specified in the net.cfg file.

When you start the test, these messages appear on each station:

MASTER STATION

   ÉÍÍÍÍÍÍ Master Station ÍÍÍÍÍÍ»
   º Waiting Sending Receiving	º
   º	\	\	\	º
   ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ

SLAVE STATION

ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ Slave  Station  ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ»
º Node Address	   : 00 80 C8 00 00 02					º
º I/O Base Address : 300H		     Test started at : 20:06:10 º
º Interrupt Number : 15(16-bit) 	     Current time    : 20:10:50 º
º Connector Type   : BNC (Thin Coax)					º
ÇÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄĶ
º									º
º Transmit Packet Length ..................................   1234	º
º Transmit Packet Counter .................................   1111	º
º Transmit Time Out Counter ...............................	 0	º
º Received Packet Length ..................................   1234	º
º Received Packet Counter .................................   1111	º
º Received Error Counter ..................................	 0	º
º No Response Counter .....................................	 0	º
º Data Mismatch Counter ...................................	 0	º
º									º
ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ



Download Driver Pack

How To Update Drivers Manually

After your driver has been downloaded, follow these simple steps to install it.

  • Expand the archive file (if the download file is in zip or rar format).

  • If the expanded file has an .exe extension, double click it and follow the installation instructions.

  • Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.

  • Find the device and model you want to update in the device list.

  • Double-click on it to open the Properties dialog box.

  • From the Properties dialog box, select the Driver tab.

  • Click the Update Driver button, then follow the instructions.

Very important: You must reboot your system to ensure that any driver updates have taken effect.

For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.

server: web1, load: 0.69