;***********************************************************************
;
; WInbond W6692 ISDN PCI adapter WinNT Setup File.
;
;***********************************************************************
[Identification]
OptionType = NetAdapter
;***********************************************************************
;
;***********************************************************************
[PlatformsSupported]
PCI
;***********************************************************************
;
;***********************************************************************
[Options]
WB692PCI
;***********************************************************************
;
;***********************************************************************
[FileConstants]
InfName = "OEMWB692.INF"
UtilityInf = "UTILITY.INF"
ParamInf = "NCPARAM.INF"
subroutineinf = "SUBROUTN.INF"
SoftwareType = "driver"
Exit_Code = 0
NetEventDLL = "%SystemRoot%\System32\netevent.dll"
IoLogMsgDLL = "%SystemRoot%\System32\IoLogMsg.dll"
Manufacturer = "Winbond"
ProductMajorVersion = "1"
ProductMinorVersion = "03"
ProductVersion = $(ProductMajorVersion)"."$(ProductMinorVersion)
ProductSoftwareName = "WB692PCI"
ProductSoftwareImagePath = "\SystemRoot\System32\drivers\WB692PCI.sys"
NetRuleSoftwareType = "WB692PCISys WB692PCIDriver"
NetRuleSoftwareUse = $(SoftwareType)
NetRuleSoftwareBindForm = """WB692PCISys"" yes no container"
NetRuleSoftwareClass = {"WB692PCIDriver basic"}
NetRuleSoftwareBindable = {"WB692PCIDriver WB692PCIAdapter non exclusive 100"}
ProductHardwareName = "WB692PCI"
NetRuleHardwareBindForm = " yes yes container"
NetRuleHardwareWB692PCIType = "WB692PCI WB692PCIAdapter"
NetRuleHardwareWB692PCIClass = {"WB692PCIAdapter basic"}
BindableWB692PCITxt = {"WB692PCIDriver WB692PCIAdapter non exclusive 100"}
DeviceMap = "HARDWARE\DEVICEMAP"
TapiDevices = "TAPI DEVICES"
TapiDeviceKey = $(ProductHardwareName)
TapiMediaType = "ISDN"
ProductKeyName = $(!NTN_SoftwareBase)"\"$(Manufacturer)"\"+
$(ProductSoftwareName)"\CurrentVersion"
ParamKeyName = $(!NTN_ServiceBase)"\"$(ProductHardwareName)+
"\Parameters"
;***********************************************************************
;
;***********************************************************************
[GeneralConstants]
from = ""
to = ""
ExitCodeOk = 0
ExitCodeCancel = 1
ExitCodeFatal = 2
KeyNull = ""
MAXIMUM_ALLOWED = 33554432
RegistryErrorIndex = NO_ERROR
KeyProduct = ""
KeyParameters = ""
TRUE = 1
FALSE = 0
NoTitle = 0
ExitState = "Active"
OldVersionExisted = $(FALSE)
DriverPath = $(!STF_NTPATH)\drivers
;***********************************************************************
;
;***********************************************************************
[Date]
Now = {} ? $(!LIBHANDLE) GetSystemDate
;***********************************************************************
;
;***********************************************************************
[Identify]
Read-Syms Identification
Set Status = STATUS_SUCCESSFUL
Set Identifier = $(OptionType)
Set Media = #("Source Media Descriptions", 1, 1)
Return $(Status) $(Identifier) $(Media)
;***********************************************************************
;
;***********************************************************************
[ReturnOptions]
Set Status = STATUS_FAILED
Set OptionList = {}
Set OptionTextList = {}
Set LanguageList = ^(LanguagesSupported, 1)
IfContains(i) $($0) in $(LanguageList)
IfStr(i) $($1) == ""
GoTo SetOptions
EndIf
Set PlatformList = ^(PlatformsSupported, 1)
IfContains(i) $($1) in $(PlatformList)
GoTo SetOptions
Else
Set Status = STATUS_NOTSUPPORTED
GoTo ExitReturnOptions
EndIf
Else
Set Status = STATUS_NOLANGUAGE
GoTo ExitReturnOptions
EndIf
SetOptions = +
Set OptionList = ^(Options, 1)
Set OptionTextList = ^(OptionsText$($0), 1)
Set Status = STATUS_SUCCESSFUL
ExitReturnOptions = +
Return $(Status) $(OptionList) $(OptionTextList)
;***********************************************************************
;
;***********************************************************************
[InstallOption]
Set Status = STATUS_FAILED
Set Option = $($1)
Set SrcDir = $($2)
Set RasDir = $($2)
Set AddCopy = $($3)
Set DoCopy = $($4)
Set DoConfig = $($5)
Set LanguageList = ^(LanguagesSupported, 1)
IfContains(i) $($0) NOT-IN $(LanguageList)
Return STATUS_NOLANGUAGE
EndIf
Set-Subst LF = "\n"
Read-Syms GeneralConstants
Read-Syms FileConstants
Read-Syms DialogConstants$(!STF_LANGUAGE)
IfStr(i) $(!NTN_Origination) == "NCPA"
Set Continue = $(OK)
EndIf
Read-Syms FileConstants$(!STF_LANGUAGE)
Detect Date
Set-Title $(FunctionTitle)$(Option)
Set to = Begin
Set from = Begin
Set CommonStatus = STATUS_SUCCESSFUL
EndWait
;***********************************************************************
;
;***********************************************************************
Begin = +
Set ActivateDetection = FALSE
IfStr(i) $(!NTN_InstallMode) == deinstall
Set StartLabel = RemoveAdapter
Else-IfStr(i) $(!NTN_InstallMode) == Update
Set StartLabel = UpgradeSoftware
Else-IfStr(i) $(!NTN_InstallMode) == bind
Set StartLabel = BindingAdapter
Else-IfStr(i) $(!NTN_InstallMode) == configure
Set StartLabel = ConfigureAdapter
Set ActivateDetection = TRUE
Set CommonStatus = STATUS_REBOOT
IfStr(i) $(ProductKeyName) == $(!NTN_RegBase)
Shell $(UtilityInf),RegistryErrorString,CANNOT_CONFIGURE_SOFTWARE
IfInt $($ShellCode) != $(!SHELL_CODE_OK)
GoTo ShellCodeError
EndIf
Set Error = $($R0)
Set from = end
Set to = end
GoTo NonFatalInfo
EndIf
Else
Set StartLabel = InstallAdapter
Set ActivateDetection = TRUE
Set OEM_ABANDON_OPTIONS = {}
Set OEM_ABANDON_SOFTWARE = FALSE
Set OEM_ABANDON_ON = TRUE
EndIf
Debug-Output $(InfName)": ================================================"
Debug-Output $(InfName)": STF_CWDIR is: "$(!STF_CWDIR)
Debug-Output $(InfName)": STF_LANGUAGE is: "$(!STF_LANGUAGE)
Debug-Output $(InfName)": Option is: "$(Option)
Debug-Output $(InfName)": !STF_NCDETECT is: "$(!STF_NCDETECT)
Debug-Output $(InfName)": !STF_NCOPTION is: "$(!STF_NCOPTION)
Debug-Output $(InfName)": !STF_NCDETCARD is: "$(!STF_NCDETCARD)
Debug-Output $(InfName)": !STF_NCDETINFO is: "$(!STF_NCDETINFO)
Debug-Output $(InfName)": ================================================"
Set DetectedCard = FALSE
IfStr(i) $(ActivateDetection) != TRUE
GoTo $(StartLabel)
EndIf
Debug-Output $(InfName)": Calling Param_SetDefaults"
Shell $(ParamInf) Param_SetDefaults {}
IfStr(i) $(!STF_NCDETECT) == YES
IfStr(i) $(!STF_NCOPTION) == $(Option)
Set DetectedCard = TRUE
EndIf
EndIf
Set from = FatalError
Set to = FatalError
GoTo $(StartLabel)
;***********************************************************************
;
;***********************************************************************
InstallAdapter = +
OpenRegKey $(!REG_H_LOCAL) "" $(ProductKeyName) $(MAXIMUM_ALLOWED) KeyProduct
IfStr $(KeyProduct) != $(KeyNull)
CloseRegKey $(KeyProduct)
IfStr(i) !(NTN_RegBase) == $(ProductKeyName)
Shell $(UtilityInf), VerExistedDlg, $(ProductSoftwareTitle),+
$(ProductVersion)
IfInt $($ShellCode) != $(!SHELL_CODE_OK)
GoTo ShellCodeError
EndIf
GoTo end
Else
Shell $(UtilityInf), CardExistedDlg
IfInt $($ShellCode) != $(!SHELL_CODE_OK)
GoTo ShellCodeError
EndIf
IfStr(i) $($R1) != "OK"
Set CommonStatus = STATUS_USERCANCEL
GoTo end
EndIf
Set OldVersionExisted = $(TRUE)
EndIf
EndIf
set Vendor = 4176
set CFID = 26258
shell $(UtilityInf),GetPCIInformation, $(Vendor) $(CFID)
ifint $($ShellCode) != $(!Shell_CODE_OK)
Debug-Output $(InfName)":ShellCode error"
GoTo ShellCodeError
endif
ifstr(i) $($R0) == {}
Debug-Output $(InfName)": Can not find the Adapter"
Set Error = $(CANNOT_FIND_ANY_CARD)
Set from = end
GoTo NonFatalInfo
endif
set AdapterList = $($R0)
ForListDo $(AdapterList)
set BusNumber = *($($),1)
set SlotNumber = *($($),2)
set FunctionNumber = *($($),3)
EndForListDo
Goto AdapterOptions
Set CurrParamSettings = {}
IfStr(i) $(DetectedCard) != TRUE
GoTo AdapterSetup
EndIf
StartWait
Shell $(ParamInf) Param_QueryCard $(!STF_NCDETCARD)
EndWait
IfStr(i) $($R0) != STATUS_SUCCESSFUL
GoTo AdapterSetup
EndIf
Set DetectedParams = $($R1)
Shell $(ParamInf) Param_SetDefaults $(DetectedParams)
GoTo AdapterSetup
;***********************************************************************
; Configuration: read the registry
;***********************************************************************
ConfigureAdapter = +
Debug-Output $(InfName)": Configure Adapter"$(!NTN_RegBase)
IfStr $(KeyProduct) == $(KeyNull)
OpenRegKey $(!REG_H_LOCAL) "" $(!NTN_RegBase) $(MAXIMUM_ALLOWED) KeyProduct
IfStr $(KeyProduct) == $(KeyNull)
Set RegistryErrorIndex = CANNOT_FIND_COMPONENT_SERVICE
Debug-Output $(InfName)": Cannot find component product key"
GoTo FatalRegistry
EndIf
EndIf
Debug-Output $(InfName)": Shelling to FindService"
Shell $(UtilityInf) FindService, $(KeyProduct)
IfInt $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output $(InfName)": FindService shell failure"
GoTo ShellCodeError
EndIf
IfStr(i) $($R0) != NO_ERROR
Debug-Output $(InfName)": FindService Shell error: "$($R0)
GoTo FatalRegistry
EndIf
Set KeyParameters = $($R2)
CloseRegKey $($R1)
IfStr $(KeyParameters) == $(KeyNull)
Set RegistryErrorIndex = CANNOT_FIND_COMPONENT_SERVICE
Debug-Output $(InfName)": Cannot find component service"
GoTo FatalRegistry
EndIf
Set OldVersionExisted = $(TRUE)
Set ValueName = ""
Set ValueData = ""
Set ValueStr = ""
Set ValueList = {}
EnumRegValue $(KeyParameters) ValueList
ForListDo $(ValueList)
Set ValueItem = $($)
Set ValueName = *($(ValueItem),1)
Set ValueData = *($(ValueItem),4)
Debug-Output $(InfName)": "$(ValueName)"="$(ValueData)
IfStr(i) $(ValueName) == "BoardName"
Set BoardName = $(ValueData)
Set TapiAddressList = *($(ValueItem),4)
EndIf
EndForListDo
Shell $(ParamInf) Param_SaveValues
Set CurrParamSettings = $($R0)
;***********************************************************************
;
;***********************************************************************
AdapterSetup = +
Shell "" DebugConfiguration "before displaying dialog"
Set from = AdapterOptions
Shell $(ParamInf) Param_ParameterConfidence
IfStr(i) $($R0) != STATUS_SUCCESSFUL
GoTo AdapterOptions
EndIf
IfStr(i) $(DetectedCard) == TRUE
IfStr(i) $(!STF_INSTALL_MODE) != CUSTOM
Debug-Output $(InfName)": Go to AdapterOptions"
GoTo AdapterOptions
EndIf
EndIf
;***********************************************************************
;
;***********************************************************************
AdapterOptions =+
IfInt $(OldVersionExisted) == $(TRUE)
IfStr(i) $(!NTN_InstallMode) == configure
GoTo WriteParameters
EndIf
EndIf
StartWait
IfInt $(OldVersionExisted) == $(FALSE)
IfStr(i) $(!NTN_InstallMode) == "install"
IfStr(i) $(DoCopy) == "YES"
Shell $(UtilityInf), DoAskSource, $(!STF_CWDDIR), $(SrcDir) YES
IfInt $($ShellCode) != $(!SHELL_CODE_OK)
GoTo ShellCodeError
Else-IfStr(i) $($R0) == STATUS_FAILED
Shell $(UtilityInf) RegistryErrorString "ASK_SOURCE_FAIL"
IfInt $($ShellCode) != $(!SHELL_CODE_OK)
GoTo ShellCodeError
EndIf
Set Error = $($R0)
GoTo FatalError
Else-IfStr(i) $($R0) == STATUS_USERCANCEL
GoTo SuccessfulOption
EndIf
Set SrcDir = $($R1)
EndIf
Install "Install-Option"
IfStr(i) $(STF_INSTALL_OUTCOME) != STF_SUCCESS
Shell $(UtilityInf) RegistryErrorString "UNABLE_COPY_FILE"
IfInt $($ShellCode) != $(!SHELL_CODE_OK)
GoTo ShellCodeError
EndIf
Set Error = $($R0)
GoTo FatalError
EndIf
EndIf
Shell $(UtilityInf), AddSoftwareComponent, $(Manufacturer), +
$(ProductSoftwareName), +
$(ProductSoftwareName), +
$(ProductSoftwareTitle), $(STF_CONTEXTINFNAME), +
$(ProductSoftwareImagePath), "kernelautostart", "NDIS", {}, "",+
$(NetEventDLL)
Set OEM_ABANDON_SOFTWARE = TRUE
IfInt $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output $(InfName)": ShellCode error"
GoTo ShellCodeError
EndIf
Set RegistryErrorIndex = $($R0)
Set KeyProduct = $($R1)
Set SoftNetRulesKey = $($R2)
CloseRegKey $($R3)
CloseRegKey $($R4)
CloseRegKey $($R5)
IfStr(i) $(RegistryErrorIndex) != NO_ERROR
EndWait
Debug-Output $(InfName)": Registry error: add software components"
CloseRegKey $(KeyProduct)
CloseRegKey $(SoftNetRulesKey)
GoTo FatalRegistry
EndIf
Set NewValueList = {+
{SoftwareType,$(NoTitle),$(!REG_VT_SZ),$(SoftwareType)},+
{MajorVersion,$(NoTitle),$(!REG_VT_DWORD),$(ProductMajorVersion)},+
{MinorVersion,$(NoTitle),$(!REG_VT_DWORD),$(ProductMinorVersion)},+
{Title,$(NoTitle),$(!REG_VT_SZ),$(ProductSoftwareTitle)},+
{Description,$(NoTitle),$(!REG_VT_SZ),$(ProductSoftwareDescription)},+
{ServiceName,$(NoTitle),$(!REG_VT_SZ),$(ProductSoftwareName)},+
{InstallDate,$(NoTitle),$(!REG_VT_DWORD),*($(Now),1)}}
Shell $(UtilityInf), AddValueList, $(KeyProduct), $(NewValueList)
IfInt $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output $(InfName)": ShellCode error."
GoTo ShellCodeError
EndIf
Set RegistryErrorIndex = $($R0)
IfStr(i) $(RegistryErrorIndex) != NO_ERROR
EndWait
Debug-Output $(InfName)": Registry error: add value list."
CloseRegKey $(KeyProduct)
CloseRegKey $(SoftNetRulesKey)
GoTo FatalRegistry
EndIf
Set NewValueList = {+
{type,$(NoTitle),$(!REG_VT_SZ),$(NetRuleSoftwareType)},+
{use,$(NoTitle),$(!REG_VT_SZ),$(NetRuleSoftwareUse)}, +
{bindform,$(NoTitle),$(!REG_VT_SZ),$(NetRuleSoftwareBindForm)}, +
{class,$(NoTitle),$(!REG_VT_MULTI_SZ),$(NetRuleSoftwareClass)}, +
{bindable,$(NoTitle),$(!REG_VT_MULTI_SZ),$(Bindable$(Option)Txt)}, +
{InfOption,$(NoTitle),$(!REG_VT_SZ),$(Option)}}
Shell $(UtilityInf), AddValueList, $(SoftNetRulesKey), $(NewValueList)
IfInt $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output $(InfName)": ShellCode error."
GoTo ShellCodeError
EndIf
Set RegistryErrorIndex = $($R0)
CloseRegKey $(KeyProduct)
CloseRegKey $(SoftNetRulesKey)
IfStr(i) $(RegistryErrorIndex) != NO_ERROR
EndWait
Debug-Output $(InfName)": Resgitry error: add value list."
GoTo FatalRegistry
EndIf
EndIf
Shell $(UtilityInf), AddHardwareComponent, $(ProductHardwareName),$(STF_CONTEXTINFNAME),$(ProductKeyName)
IfInt $($R4) != -1
Set OEM_ABANDON_OPTIONS = >($(OEM_ABANDON_OPTIONS), $(!NTN_SoftwareBase)"\Microsoft\Windows NT\CurrentVersion\NetworkCards\"$($R4))
EndIf
IfInt $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output $(InfName)": Cannot add hardware component"
GoTo ShellCodeError
EndIf
Set RegistryErrorIndex = $($R0)
IfStr(i) $(RegistryErrorIndex) != NO_ERROR
EndWait
Debug-Output $(InfName)": Registry error: add hardware component"
CloseRegKey $($R1)
CloseRegKey $($R2)
CloseRegKey $($R3)
GoTo FatalRegistry
EndIf
Set KeyParameters = $($R3)
Set KeyAdapterRules = $($R2)
Set AdapterNumber = $($R4)
Set NewValueList = {+
{Manufacturer,$(NoTitle),$(!REG_VT_SZ),$(Manufacturer)},+
{Title,$(NoTitle),$(!REG_VT_SZ),"["$($R4)"] "$(ProductHardware$(Option)Title)},+
{Description,$(NoTitle),$(!REG_VT_SZ),$(ProductHardware$(Option)Description)},+
{ProductName,$(NoTitle),$(!REG_VT_SZ),$(ProductHardwareName)},+
{ServiceName,$(NoTitle),$(!REG_VT_SZ),$($R5)},+
{InstallDate,$(NoTitle),$(!REG_VT_DWORD),*($(Now),1)}}
Shell $(UtilityInf), AddValueList, $($R1), $(NewValueList)
IfInt $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output $(InfName)": ShellCode error"
GoTo ShellCodeError
EndIf
CloseRegKey $($R1)
Set TempProdName = """"$(ProductHardwareName)$(AdapterNumber)""""
Set TempBindForm = $(TempProdName)$(NetRuleHardwareBindForm)
Set NewValueList = {+
{type,$(NoTitle),$(!REG_VT_SZ),$(NetRuleHardware$(Option)Type)},+
{bindform,$(NoTitle),$(!REG_VT_SZ),$(TempBindForm)}, +
{class,$(NoTitle),$(!REG_VT_MULTI_SZ),$(NetRuleHardware$(Option)Class)}, +
{InfOption,$(NoTitle),$(!REG_VT_SZ),$(Option)}}
Shell $(UtilityInf), AddValueList, $(KeyAdapterRules), $(NewValueList)
IfInt $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output $(InfName)": ShellCode error."
GoTo ShellCodeError
EndIf
Set RegistryErrorIndex = $($R0)
IfStr(i) $(RegistryErrorIndex) != NO_ERROR
EndWait
Debug-Output $(InfName)": Resgitry error: add value list."
CloseRegKey $(KeyParameters)
CloseRegKey $(KeyAdapterRules)
GoTo FatalRegistry
EndIf
CloseRegKey $(KeyAdapterRules)
GoTo WriteParameters
;***********************************************************************
;
;***********************************************************************
WriteParameters = +
Debug-Output $(InfName)": Open the dialog box for user input"
Debug-Output $(InfName)": cfgResult = "$(cfgResult)
Debug-Output $(InfName)": SwithType = "$(Line0.SwitchType)
Debug-Output $(InfName)": Ch0.Phone = "$(Line0.Channel0.Phone)
Debug-Output $(InfName)": Ch0.SPID = "$(Line0.Channel0.SPID)
Debug-Output $(InfName)": Ch1.Phone = "$(Line0.Channel1.Phone)
Debug-Output $(InfName)": Ch1.SPID = "$(Line0.Channel1.SPID)
set BoardName = "WB692PCI"
set NumberofLines = 1
Debug-Output $(InfName)": AdapterNumber = "$(AdapterNumber)
IfStr(i) $(!NTN_InstallMode) == install
Set TapiAddressList = {$(AdapterNumber)" 1 0"}
IfStr(i) $(Option) == WB692PCI
Set TapiAddressList = >($(TapiAddressList),$(AdapterNumber)" 2 0")
EndIf
Else
Debug-Output $(InfName)": TapiAddressList = "$(TapiAddressList)
EndIf
Set BusType = 5
Set NewValueList = {+
{BusType,$(NoTitle),$(!REG_VT_DWORD),$(BusType)},+
{BusNumber,$(NoTitle),$(!REG_VT_DWORD),$(BusNumber)},+
{SlotNumber,$(NoTitle),$(!REG_VT_DWORD),$(SlotNumber)},+
{FunctionNumber,$(NoTitle),$(!REG_VT_DWORD),$(FunctionNumber)},+
{BoardName,$(NoTitle),$(!REG_VT_SZ),$(BoardName)},+
{DeviceName,$(NoTitle),$(!REG_VT_SZ),$(ProductHardwareName)},+
{AddressList,$(NoTitle),$(!REG_VT_MULTI_SZ),$(TapiAddressList)},+
{MediaType,$(NoTitle),$(!REG_VT_SZ),$(TapiMediaType)},+
{NumberofLines,$(NoTitle),$(!REG_VT_DWORD),$(NumberofLines)},+
}
Shell $(UtilityInf), AddValueList, $(KeyParameters), $(NewValueList)
CloseRegKey $(KeyParameters)
IfInt $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output $(InfName)": ShellCode error."
GoTo ShellCodeError
EndIf
Set RegistryErrorIndex = $($R0)
IfStr(i) $(RegistryErrorIndex) != NO_ERROR
Debug-Output $(InfName)": Registry error: Add value list"
GoTo FatalRegistry
EndIf
IfStr(i) $(!NTN_InstallMode) == configure
Debug-Output $(InfName)": Configuration is done"
GoTo SuccessfulOption
EndIf
OpenRegKey $(!REG_H_LOCAL) "" "HARDWARE\DEVICEMAP" $(MAXIMUM_ALLOWED) BaseKey
shell "" WbCreateRegKey $(BaseKey) "TAPI DEVICES\WB692PCI"
IfStr(i) $($R0) != NO_ERROR
Debug-Output $(InfName)": Error creating registry key!"
GoTo FatalRegistry
EndIf
Set TapiDeviceKey = $($R1)
Set NewValueList = {+
{Address,$(NoTitle),$(!REG_VT_MULTI_SZ),$(TapiAddressList)},+
{"Media Type",$(NoTitle),$(!REG_VT_SZ),$(TapiMediaType)}}
Shell $(UtilityInf), AddValueList, $(TapiDeviceKey), $(NewValueList)
IfInt $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output $(InfName)": ShellCode error."
GoTo ShellCodeError
EndIf
Set RegistryErrorIndex = $($R0)
IfStr(i) $(RegistryErrorIndex) != NO_ERROR
Debug-Output $(InfName)": Registry error: Add value list"
GoTo FatalRegistry
EndIf
CloseRegKey $(TapiDeviceKey)
CloseRegKey $(BaseKey)
Read-Syms InvokeRasDlg$(!STF_LANGUAGE)
Shell "oemnsvra.inf" CheckRasInstalled
IfInt $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output $(InfName)": Error Shelling the RAS INF file oemnsvra.inf"
Shell "subroutn.inf" SetupMessage, $(!STF_LANGUAGE), +
"STATUS", $(InvokeRasError)
IfInt $($ShellCode) != $(!SHELL_CODE_OK)
GoTo ShellCodeError
EndIf
GoTo SuccessfulOption
EndIf
Set RasInstalled = $($R0)
Debug-Output $(InfName)": Is RAS Installed? "$(RasInstalled)
IfStr(i) $(RasInstalled) == FALSE
Shell "subroutn.inf" SetupMessage, $(!STF_LANGUAGE), "STATUS", +
$(InvokeRasSetupMsg)
IfInt $($ShellCode) != $(!SHELL_CODE_OK)
GoTo SuccessfulOption
EndIf
Else
Shell "subroutn.inf" SetupMessage, $(!STF_LANGUAGE), "STATUS", +
$(InvokeRasConfigMsg)
IfInt $($ShellCode) != $(!SHELL_CODE_OK)
GoTo SuccessfulOption
EndIf
EndIf
IfStr(i) $(!STF_IDW) == TRUE
Set AddCopy = NO
Set DoCopy = NO
Set DoConfig = NO
Else
Set AddCopy = YES
Set DoCopy = YES
Set DoConfig = YES
EndIf
Set SaveNTN_InstallMode = $(!NTN_InstallMode)
IfStr(i) $(RasInstalled) == TRUE
Set !NTN_InstallMode = configure
Else
Set !NTN_InstallMode = install
EndIf
set SaveSTF_SRCDIR_OVERRIDE = $(!STF_SRCDIR_OVERRIDE)
set !STF_SRCDIR_OVERRIDE = ""
Debug-Output $InfName)": STF_LANGUAGE = "$(!STF_LANGUAGE)
Debug-Output $InfName)": RasDir = "$(RasDir)
Debug-Output $InfName)": AddCopy = "$(AddCopy)
Debug-Output $InfName)": DoCopy = "$(DoCopy)
Debug-Output $InfName)": DoConfig = "$(DoConfig)
Shell "oemnsvra.inf" InstallOption $(!STF_LANGUAGE) "RAS" $(RasDir) $(AddCopy) $(DoCopy) $(DoConfig)
set !NTN_InstallMode = $(SaveNTN_InstallMode)
set !STF_SRCDIR_OVERRIDE = $(SaveSTF_SRCDIR_OVERRIDE)
IfInt $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output $(InfName)": Error Shelling the RAS INF file oemnsvra.inf"
Shell "subroutn.inf" SetupMessage, $(!STF_LANGUAGE), "STATUS", +
$(InvokeRasError)
IfInt $($ShellCode) != $(!SHELL_CODE_OK)
GoTo ShellCodeError
EndIf
GoTo SuccessfulOption
EndIf
SkipRasSetup =+
EndWait
GoTo SuccessfulOption
;***********************************************************************
;
;***********************************************************************
BindingAdapter =+
Set Error = "Binding: Sorry, not yet implemented."
GoTo FatalError
;***********************************************************************
;
;***********************************************************************
RemoveAdapter = +
IfStr(i) $(ProductKeyName) == $(!NTN_RegBase)
Shell $(UtilityInf), RemoveSoftwareComponent, $(Manufacturer), +
$(ProductSoftwareName)
IfInt $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output $(InfName)": ShellCode error"
GoTo ShellCodeError
EndIf
Set RegistryErrorIndex = $($R0)
IfStr(i) $(RegistryErrorIndex) != NO_ERROR
GoTo FatalRegistry
EndIf
Else
Shell $(UtilityInf), RemoveHardwareComponent, $(Manufacturer), +
$(ProductSoftwareName), $(!NTN_RegBase)
IfInt $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output $(InfName)": ShellCode error"
GoTo ShellCodeError
EndIf
Set RegistryErrorIndex = $($R0)
IfStr(i) $(RegistryErrorIndex) != NO_ERROR
GoTo FatalRegistry
EndIf
EndIf
GoTo end
;***********************************************************************
;
;***********************************************************************
UpgradeSoftware = +
IfStr(i) $(ProductKeyName) == $(!NTN_RegBase)
OpenRegKey $(!REG_H_LOCAL) "" $(ProductKeyName) $(MAXIMUM_ALLOWED) KeyProduct
IfStr $(KeyProduct) != $(KeyNull)
GetRegValue $(KeyProduct),"MajorVersion", VersionInfo
Set Version = *($(VersionInfo), 4)
Shell $(UtilityInf), GetInfFileNameFromRegistry, $(KeyProduct)
IfInt $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output $(InfName)": ShellCode error"
GoTo ShellCodeError
EndIf
Set !UG_Filename = $($R0)
IfStr(i) $(!UG_Filename) != ""
install "Install-Update"
IfStr(i) $(STF_INSTALL_OUTCOME) != STF_SUCCESS
GoTo FatalError
EndIf
EndIf
SetRegValue $(KeyProduct) {MajorVersion,$(NoTitle),$(!REG_VT_SZ),$(ProductMajorVersion)}
SetRegValue $(KeyProduct) {MinorVersion,$(NoTitle),$(!REG_VT_SZ),$(ProductMinorVersion)}
IfInt $(Version) != $(ProductVersion)
EndIf
CloseRegKey $(KeyProduct)
Else
GoTo FatalRegistry
EndIf
Else
OpenRegKey $(!REG_H_LOCAL) "" $(!NTN_RegBase) +
$(MAXIMUM_ALLOWED) NetworkCardKey
IfStr(i) $(NetworkCardKey) != $(KeyNull)
GetRegValue $(NetworkCardKey),"ServiceName", ServiceNameInfo
Set ServiceName = *($(ServiceNameInfo), 4)
OpenRegKey $(NetworkCardKey) "" "NetRules" +
$(MAXIMUM_ALLOWED) NetRuleKey
IfStr(i) $(NetRuleKey) != $(KeyNull)
Else
GoTo FatalRegistry
EndIf
CloseRegKey $(NetRules)
CloseRegKey $(NetworkCardKey)
Else
GoTo FatalRegistry
EndIf
OpenRegKey $(!REG_H_LOCAL) "" +
$(!NTN_ServiceBase)"\"$(ServiceName) +
$(MAXIMUM_ALLOWED) ServiceKey
IfStr(i) $(ServiceKey) != $(KeyNull)
CloseRegKey $(ServiceKey)
Else
GoTo FatalRegistry
EndIf
EndIf
GoTo end
;***********************************************************************
;
;***********************************************************************
SuccessfulOption = +
GoTo end
;***********************************************************************
;
;***********************************************************************
Abandon = +
ForListDo $(OEM_ABANDON_OPTIONS)
Shell $(UtilityInf), RemoveHardwareComponent, $(Manufacturer), +
$(ProductSoftwareName), $($)
IfInt $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output $(InfName)": ShellCode error"
GoTo ShellCodeError
EndIf
Set RegistryErrorIndex = $($R0)
IfStr(i) $(RegistryErrorIndex) != NO_ERROR
GoTo FatalRegistry
EndIf
EndForListDo
IfStr(i) $(OEM_ABANDON_SOFTWARE) == TRUE
Shell $(UtilityInf), RemoveSoftwareComponent, $(Manufacturer), +
$(ProductSoftwareName), FALSE
IfInt $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output $(InfName)": ShellCode error"
GoTo ShellCodeError
EndIf
Set RegistryErrorIndex = $($R0)
IfStr(i) $(RegistryErrorIndex) != NO_ERROR
GoTo FatalRegistry
EndIf
EndIf
GoTo end
;***********************************************************************
;
;***********************************************************************
WarningMsg = +
Shell $(subroutineinf) SetupMessage, $(!STF_LANGUAGE), "WARNING", $(Error)
IfInt $($ShellCode) != $(!SHELL_CODE_OK)
GoTo ShellCodeError
EndIf
IfStr(i) $($R1) == "OK"
GoTo $(to)
Else-IfStr(i) $($R1) == "CANCEL"
GoTo $(from)
EndIf
GoTo end
;***********************************************************************
;
;***********************************************************************
NonFatalInfo = +
Set Severity = STATUS
Set CommonStatus = STATUS_USERCANCEL
IfStr(i) $(Error) == ""
Set Severity = NONFATAL
Shell $(UtilityInf) RegistryErrorString "SETUP_FAIL"
IfInt $($ShellCode) != $(!SHELL_CODE_OK)
GoTo ShellCodeError
EndIf
Set Error = $($R0)
EndIf
Shell $(subroutineinf) SetupMessage, $(!STF_LANGUAGE), $(Severity), $(Error)
IfInt $($ShellCode) != $(!SHELL_CODE_OK)
GoTo ShellCodeError
EndIf
IfStr(i) $($R1) == "OK"
GoTo $(from)
EndIf
GoTo end
;***********************************************************************
;
;***********************************************************************
FatalRegistry = +
Shell $(UtilityInf) RegistryErrorString $(RegistryErrorIndex)
IfInt $($ShellCode) != $(!SHELL_CODE_OK)
GoTo ShellCodeError
EndIf
Set Error = $($R0)
GoTo FatalError
;***********************************************************************
;
;***********************************************************************
FatalDetect = +
Shell $(UtilityInf),RegistryErrorString,CANNOT_DETECT
IfInt $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output $(InfName)": ShellCode error: cannot get an error string."
GoTo ShellCodeError
EndIf
Set Error = $($R0)
GoTo FatalError
;***********************************************************************
;
;***********************************************************************
FatalError = +
IfStr(i) $(Error) == ""
Shell $(UtilityInf) RegistryErrorString "SETUP_FAIL"
IfInt $($ShellCode) != $(!SHELL_CODE_OK)
GoTo ShellCodeError
EndIf
Set Error = $($R0)
EndIf
Shell $(subroutineinf) SetupMessage, $(!STF_LANGUAGE), "FATAL", $(Error)
IfInt $($ShellCode) != $(!SHELL_CODE_OK)
GoTo ShellCodeError
EndIf
GoTo SetFailed
;***********************************************************************
;
;***********************************************************************
ShellCodeError = +
Set DlgType = "MessageBox"
Set STF_MB_TITLE = $(ShellCodeErrorTitle)
Set STF_MB_TEXT = $(ShellCodeErrorText)
Set STF_MB_TYPE = 1
Set STF_MB_ICON = 3
Set STF_MB_DEF = 1
UI Start "Error Message"
GoTo SetFailed
;***********************************************************************
;
;***********************************************************************
SetFailed = +
Set CommonStatus = STATUS_FAILED
IfStr(i) $(OEM_ABANDON_ON) == TRUE
Set OEM_ABANDON_ON = FALSE
GoTo Abandon
EndIf
GoTo end
;***********************************************************************
;
;***********************************************************************
end = +
Return $(CommonStatus)
;***********************************************************************
;
;***********************************************************************
[WbCreateRegKey]
Debug-Output $(InfName)": Entering [WbCreateRegKey]"
Set ECR_Result = NO_ERROR
Set ECR_BaseKeyHandle = $($0)
Set ECR_NewPath = $($1)
Set KeyNull = ""
Set MAXIMUM_ALLOWED = 33554432
Debug-Output $(InfName)": WbCreateRegKey - ECR_BaseKeyHandle ="$(ECR_BaseKeyHandle)
Debug-Output $(InfName)": ECR_NewPath = "$(ECR_NewPath)
Debug-Output $(InfName)": MAXIMUM_ALLOWED = "$(MAXIMUM_ALLOWED)
Debug-Output $(InfName)": KeyNull = "$(KeyNull)
OpenRegKey $(ECR_BaseKeyHandle) "" $(ECR_NewPath) $(MAXIMUM_ALLOWED) +
ECR_BaseKey
Debug-Output $(InfName)": ECR_BaseKey = "$(ECR_BaseKey)
Debug-Output $(InfName)": OpenRegKey returned "$($R0)
IfStr $(ECR_BaseKey) == $(KeyNull)
Debug-Output $(InfName)": ECR_BaseKey == KeyNull"
Else
Debug-Output $(InfName)": ECR_BaseKey != KeyNull"
Set ECR_KeyHandle = $(ECR_BaseKey)
GoTo ECR_Return
EndIf
Set ECR_TmpPath = ""
Split-String $(ECR_NewPath) "\" ECR_PList
Debug-Output $(InfName)": ECR_PList = "$(ECR_PList)
ForListDo $(ECR_PList)
IfStr(i) $($) != "\"
IfInt $(#) == 1
Set ECR_TmpPath = $($)
Else
Set ECR_TmpPath = $(ECR_TmpPath)"\"$($)
EndIf
Debug-Output $(InfName)": Determining if "$(ECR_TmpPath)" exists"
OpenRegKey $(ECR_BaseKeyHandle) "" $(ECR_TmpPath) $(MAXIMUM_ALLOWED) ECR_BaseKey
IfStr $(ECR_BaseKey) == $(KeyNull)
Debug-Output $(InfName)": Creating "$(ECR_TmpPath)
CreateRegKey $(ECR_BaseKeyHandle) {$(ECR_TmpPath),0,GenericClass} "" $(MAXIMUM_ALLOWED) "" ECR_KeyHandle
IfStr(i) $(ECR_KeyHandle) == $(KeyNull)
Set ECR_Result = $($R0)
GoTo ECR_Return
EndIf
EndIf
EndIf
EndForListDo
ECR_Return = +
Return $(ECR_Result) $(ECR_KeyHandle)
;***********************************************************************
;
;***********************************************************************
[DebugConfiguration]
Debug-Output $(!p:InfName)": **CONFIGURATION STATE: "$($0)
Return
;***********************************************************************
;
;***********************************************************************
[Install-Option]
Set STF_VITAL = ""
IfStr(i) $(AddCopy) == "YES"
AddSectionFilesToCopyList Files-$(Option) $(SrcDir) $(!STF_WINDOWSSYSPATH)\drivers
EndIf
IfStr(i) $(DoCopy) == "YES"
Set !STF_NCPA_FLUSH_COPYLIST = TRUE
CopyFilesInCopyList
EndIf
Exit
;***********************************************************************
;
;***********************************************************************
[Install-Update]
Set STF_VITAL = ""
Set STF_OVERWRITE = "VERIFYSOURCEOLDER"
AddSectionFilesToCopyList Files-$(Option) $(SrcDir) $(!STF_WINDOWSSYSPATH)\drivers
AddSectionFilesToCopyList Files-Inf $(SrcDir) $(!STF_WINDOWSSYSPATH)
Set !STF_NCPA_FLUSH_COPYLIST = TRUE
CopyFilesInCopyList
Exit
;***********************************************************************
;
;***********************************************************************
[Source Media Descriptions]
; 1 = "Winbond W6692 ISDN PCI cardWindow NT Setup Disk" , TAGFILE = WB692PCI.SYS
1 = "Winbond W6692 ISDN PCI cardWindow NT Setup Disk"
;***********************************************************************
;
;***********************************************************************
[ProductType]
STF_PRODUCT = Winnt
STF_PLATFORM = I386
;***********************************************************************
;
;***********************************************************************
[Files-Inf]
1, oemsetnt.inf, SIZE=46000, RENAME=$(!UG_Filename)
;***********************************************************************
;
;***********************************************************************
[Files-WB692PCI]
1, WB692PCI.SYS, SIZE=383000
;***********************************************************************
;***********************************************************************
;***********************************************************************
;
;***********************************************************************
[LanguagesSupported]
ENG
;***********************************************************************
;
;***********************************************************************
[OptionsTextENG]
WB692PCI = "Winbond ISDN PCI CARD"
;***********************************************************************
;
;***********************************************************************
[FileConstantsENG]
ProCaption = "Windows NT Setup"
ProCancel = "Cancel"
ProCancelMsg = "Windows NT Networking is not correctly installed. "+
"Are you sure you want to cancel copying files?"
ProCancelCap = "Network Setup Message"
ProText1 = "Copying:"
ProText2 = "To:"
FunctionTitleWB692PCI = "Winbond ISDN PCI Card Setup"
ProductSoftwareDescription = "Winbond ISDN PCI CARD Driver"
ProductHardwareWB692PCIDescription = "Winbond ISDN PCI CARD"
ProductSoftwareTitle = "Winbond ISDN PCI CARD Driver"
ProductHardwareWB692PCITitle = "Winbond ISDN PCI CARD"
ShellCodeErrorTitle = "Error: "$(FunctionTitle)$(Option))
ShellCodeErrorText = "Shell Code Error."
CANNOT_FIND_ANY_CARD = "Network card is not present in the system"
;***********************************************************************
;
;***********************************************************************
[DialogConstantsENG]
Help = "&Help"
Exit = "Cancel"
OK = "OK"
HelpContext = ""
Continue = "Continue"
Cancel = "Cancel"
;***********************************************************************
;
;***********************************************************************
[FileDependentDlgENG]
DlgType = "RadioCombination"
DlgType = "Edit"
DlgType = "Radio"
DlgTemplate = "NE2000"
Caption = $(FunctionTitle)$(Option)
Combo1List = $(MASTER_List)
Combo1Out = $(MasterEnable)
Combo2List = $(IO_Hex_List)
Combo2Out = $(IO_Hex_Value)
ComboListItemsIn = {Combo1List, Combo2List}
ComboListItemsOut = {Combo1Out, Combo2Out}
EditTextIn = "12345"
EditTextLim = "987654321"
CBOptionsGreyed = {}
NotifyFields = {NO, NO}
; HelpContext = $(!IDH_DB_OEMNADN2_INS)
;***********************************************************************
;
;***********************************************************************
[InvokeRasDlgENG]
InvokeRasSetupMsg = "Winbond ISDN PCI card setup is complete. "+
"Remote Access Services (RAS) will now be installed. "+
"Please configure the ISDN ports in RAS "+
"setup to enable you to use RAS over the ISDN."
InvokeRasConfigMsg = "Winbond ISDN PCI card setup is complete. "+
"Remote Access Services (RAS) setup will now be invoked. "+
"Please configure one or more ISDN ports in RAS "+
"setup to enable you to use RAS over the ISDN."
InvokeRasError = "Winbond ISDN PCI card setup encountered an error "+
"while invoking the RAS setup INF file (OEMNSVRA.INF). "+
"Please make sure that the file is present in the "+
"System32 directory and is the proper file."
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.