;*********************************************************************** ; ; WInbond W6692 ISDN PCI adapter WinNT Setup File. ; ;*********************************************************************** [Identification] OptionType = NetAdapter ;*********************************************************************** ; ;*********************************************************************** [PlatformsSupported] PCI ;*********************************************************************** ; ;*********************************************************************** [Options] WB692PCI ;*********************************************************************** ; ;*********************************************************************** [FileConstants] InfName = "OEMWB692.INF" UtilityInf = "UTILITY.INF" ParamInf = "NCPARAM.INF" subroutineinf = "SUBROUTN.INF" SoftwareType = "driver" Exit_Code = 0 NetEventDLL = "%SystemRoot%\System32\netevent.dll" IoLogMsgDLL = "%SystemRoot%\System32\IoLogMsg.dll" Manufacturer = "Winbond" ProductMajorVersion = "1" ProductMinorVersion = "03" ProductVersion = $(ProductMajorVersion)"."$(ProductMinorVersion) ProductSoftwareName = "WB692PCI" ProductSoftwareImagePath = "\SystemRoot\System32\drivers\WB692PCI.sys" NetRuleSoftwareType = "WB692PCISys WB692PCIDriver" NetRuleSoftwareUse = $(SoftwareType) NetRuleSoftwareBindForm = """WB692PCISys"" yes no container" NetRuleSoftwareClass = {"WB692PCIDriver basic"} NetRuleSoftwareBindable = {"WB692PCIDriver WB692PCIAdapter non exclusive 100"} ProductHardwareName = "WB692PCI" NetRuleHardwareBindForm = " yes yes container" NetRuleHardwareWB692PCIType = "WB692PCI WB692PCIAdapter" NetRuleHardwareWB692PCIClass = {"WB692PCIAdapter basic"} BindableWB692PCITxt = {"WB692PCIDriver WB692PCIAdapter non exclusive 100"} DeviceMap = "HARDWARE\DEVICEMAP" TapiDevices = "TAPI DEVICES" TapiDeviceKey = $(ProductHardwareName) TapiMediaType = "ISDN" ProductKeyName = $(!NTN_SoftwareBase)"\"$(Manufacturer)"\"+ $(ProductSoftwareName)"\CurrentVersion" ParamKeyName = $(!NTN_ServiceBase)"\"$(ProductHardwareName)+ "\Parameters" ;*********************************************************************** ; ;*********************************************************************** [GeneralConstants] from = "" to = "" ExitCodeOk = 0 ExitCodeCancel = 1 ExitCodeFatal = 2 KeyNull = "" MAXIMUM_ALLOWED = 33554432 RegistryErrorIndex = NO_ERROR KeyProduct = "" KeyParameters = "" TRUE = 1 FALSE = 0 NoTitle = 0 ExitState = "Active" OldVersionExisted = $(FALSE) DriverPath = $(!STF_NTPATH)\drivers ;*********************************************************************** ; ;*********************************************************************** [Date] Now = {} ? $(!LIBHANDLE) GetSystemDate ;*********************************************************************** ; ;*********************************************************************** [Identify] Read-Syms Identification Set Status = STATUS_SUCCESSFUL Set Identifier = $(OptionType) Set Media = #("Source Media Descriptions", 1, 1) Return $(Status) $(Identifier) $(Media) ;*********************************************************************** ; ;*********************************************************************** [ReturnOptions] Set Status = STATUS_FAILED Set OptionList = {} Set OptionTextList = {} Set LanguageList = ^(LanguagesSupported, 1) IfContains(i) $($0) in $(LanguageList) IfStr(i) $($1) == "" GoTo SetOptions EndIf Set PlatformList = ^(PlatformsSupported, 1) IfContains(i) $($1) in $(PlatformList) GoTo SetOptions Else Set Status = STATUS_NOTSUPPORTED GoTo ExitReturnOptions EndIf Else Set Status = STATUS_NOLANGUAGE GoTo ExitReturnOptions EndIf SetOptions = + Set OptionList = ^(Options, 1) Set OptionTextList = ^(OptionsText$($0), 1) Set Status = STATUS_SUCCESSFUL ExitReturnOptions = + Return $(Status) $(OptionList) $(OptionTextList) ;*********************************************************************** ; ;*********************************************************************** [InstallOption] Set Status = STATUS_FAILED Set Option = $($1) Set SrcDir = $($2) Set RasDir = $($2) Set AddCopy = $($3) Set DoCopy = $($4) Set DoConfig = $($5) Set LanguageList = ^(LanguagesSupported, 1) IfContains(i) $($0) NOT-IN $(LanguageList) Return STATUS_NOLANGUAGE EndIf Set-Subst LF = "\n" Read-Syms GeneralConstants Read-Syms FileConstants Read-Syms DialogConstants$(!STF_LANGUAGE) IfStr(i) $(!NTN_Origination) == "NCPA" Set Continue = $(OK) EndIf Read-Syms FileConstants$(!STF_LANGUAGE) Detect Date Set-Title $(FunctionTitle)$(Option) Set to = Begin Set from = Begin Set CommonStatus = STATUS_SUCCESSFUL EndWait ;*********************************************************************** ; ;*********************************************************************** Begin = + Set ActivateDetection = FALSE IfStr(i) $(!NTN_InstallMode) == deinstall Set StartLabel = RemoveAdapter Else-IfStr(i) $(!NTN_InstallMode) == Update Set StartLabel = UpgradeSoftware Else-IfStr(i) $(!NTN_InstallMode) == bind Set StartLabel = BindingAdapter Else-IfStr(i) $(!NTN_InstallMode) == configure Set StartLabel = ConfigureAdapter Set ActivateDetection = TRUE Set CommonStatus = STATUS_REBOOT IfStr(i) $(ProductKeyName) == $(!NTN_RegBase) Shell $(UtilityInf),RegistryErrorString,CANNOT_CONFIGURE_SOFTWARE IfInt $($ShellCode) != $(!SHELL_CODE_OK) GoTo ShellCodeError EndIf Set Error = $($R0) Set from = end Set to = end GoTo NonFatalInfo EndIf Else Set StartLabel = InstallAdapter Set ActivateDetection = TRUE Set OEM_ABANDON_OPTIONS = {} Set OEM_ABANDON_SOFTWARE = FALSE Set OEM_ABANDON_ON = TRUE EndIf Debug-Output $(InfName)": ================================================" Debug-Output $(InfName)": STF_CWDIR is: "$(!STF_CWDIR) Debug-Output $(InfName)": STF_LANGUAGE is: "$(!STF_LANGUAGE) Debug-Output $(InfName)": Option is: "$(Option) Debug-Output $(InfName)": !STF_NCDETECT is: "$(!STF_NCDETECT) Debug-Output $(InfName)": !STF_NCOPTION is: "$(!STF_NCOPTION) Debug-Output $(InfName)": !STF_NCDETCARD is: "$(!STF_NCDETCARD) Debug-Output $(InfName)": !STF_NCDETINFO is: "$(!STF_NCDETINFO) Debug-Output $(InfName)": ================================================" Set DetectedCard = FALSE IfStr(i) $(ActivateDetection) != TRUE GoTo $(StartLabel) EndIf Debug-Output $(InfName)": Calling Param_SetDefaults" Shell $(ParamInf) Param_SetDefaults {} IfStr(i) $(!STF_NCDETECT) == YES IfStr(i) $(!STF_NCOPTION) == $(Option) Set DetectedCard = TRUE EndIf EndIf Set from = FatalError Set to = FatalError GoTo $(StartLabel) ;*********************************************************************** ; ;*********************************************************************** InstallAdapter = + OpenRegKey $(!REG_H_LOCAL) "" $(ProductKeyName) $(MAXIMUM_ALLOWED) KeyProduct IfStr $(KeyProduct) != $(KeyNull) CloseRegKey $(KeyProduct) IfStr(i) !(NTN_RegBase) == $(ProductKeyName) Shell $(UtilityInf), VerExistedDlg, $(ProductSoftwareTitle),+ $(ProductVersion) IfInt $($ShellCode) != $(!SHELL_CODE_OK) GoTo ShellCodeError EndIf GoTo end Else Shell $(UtilityInf), CardExistedDlg IfInt $($ShellCode) != $(!SHELL_CODE_OK) GoTo ShellCodeError EndIf IfStr(i) $($R1) != "OK" Set CommonStatus = STATUS_USERCANCEL GoTo end EndIf Set OldVersionExisted = $(TRUE) EndIf EndIf set Vendor = 4176 set CFID = 26258 shell $(UtilityInf),GetPCIInformation, $(Vendor) $(CFID) ifint $($ShellCode) != $(!Shell_CODE_OK) Debug-Output $(InfName)":ShellCode error" GoTo ShellCodeError endif ifstr(i) $($R0) == {} Debug-Output $(InfName)": Can not find the Adapter" Set Error = $(CANNOT_FIND_ANY_CARD) Set from = end GoTo NonFatalInfo endif set AdapterList = $($R0) ForListDo $(AdapterList) set BusNumber = *($($),1) set SlotNumber = *($($),2) set FunctionNumber = *($($),3) EndForListDo Goto AdapterOptions Set CurrParamSettings = {} IfStr(i) $(DetectedCard) != TRUE GoTo AdapterSetup EndIf StartWait Shell $(ParamInf) Param_QueryCard $(!STF_NCDETCARD) EndWait IfStr(i) $($R0) != STATUS_SUCCESSFUL GoTo AdapterSetup EndIf Set DetectedParams = $($R1) Shell $(ParamInf) Param_SetDefaults $(DetectedParams) GoTo AdapterSetup ;*********************************************************************** ; Configuration: read the registry ;*********************************************************************** ConfigureAdapter = + Debug-Output $(InfName)": Configure Adapter"$(!NTN_RegBase) IfStr $(KeyProduct) == $(KeyNull) OpenRegKey $(!REG_H_LOCAL) "" $(!NTN_RegBase) $(MAXIMUM_ALLOWED) KeyProduct IfStr $(KeyProduct) == $(KeyNull) Set RegistryErrorIndex = CANNOT_FIND_COMPONENT_SERVICE Debug-Output $(InfName)": Cannot find component product key" GoTo FatalRegistry EndIf EndIf Debug-Output $(InfName)": Shelling to FindService" Shell $(UtilityInf) FindService, $(KeyProduct) IfInt $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output $(InfName)": FindService shell failure" GoTo ShellCodeError EndIf IfStr(i) $($R0) != NO_ERROR Debug-Output $(InfName)": FindService Shell error: "$($R0) GoTo FatalRegistry EndIf Set KeyParameters = $($R2) CloseRegKey $($R1) IfStr $(KeyParameters) == $(KeyNull) Set RegistryErrorIndex = CANNOT_FIND_COMPONENT_SERVICE Debug-Output $(InfName)": Cannot find component service" GoTo FatalRegistry EndIf Set OldVersionExisted = $(TRUE) Set ValueName = "" Set ValueData = "" Set ValueStr = "" Set ValueList = {} EnumRegValue $(KeyParameters) ValueList ForListDo $(ValueList) Set ValueItem = $($) Set ValueName = *($(ValueItem),1) Set ValueData = *($(ValueItem),4) Debug-Output $(InfName)": "$(ValueName)"="$(ValueData) IfStr(i) $(ValueName) == "BoardName" Set BoardName = $(ValueData) Set TapiAddressList = *($(ValueItem),4) EndIf EndForListDo Shell $(ParamInf) Param_SaveValues Set CurrParamSettings = $($R0) ;*********************************************************************** ; ;*********************************************************************** AdapterSetup = + Shell "" DebugConfiguration "before displaying dialog" Set from = AdapterOptions Shell $(ParamInf) Param_ParameterConfidence IfStr(i) $($R0) != STATUS_SUCCESSFUL GoTo AdapterOptions EndIf IfStr(i) $(DetectedCard) == TRUE IfStr(i) $(!STF_INSTALL_MODE) != CUSTOM Debug-Output $(InfName)": Go to AdapterOptions" GoTo AdapterOptions EndIf EndIf ;*********************************************************************** ; ;*********************************************************************** AdapterOptions =+ IfInt $(OldVersionExisted) == $(TRUE) IfStr(i) $(!NTN_InstallMode) == configure GoTo WriteParameters EndIf EndIf StartWait IfInt $(OldVersionExisted) == $(FALSE) IfStr(i) $(!NTN_InstallMode) == "install" IfStr(i) $(DoCopy) == "YES" Shell $(UtilityInf), DoAskSource, $(!STF_CWDDIR), $(SrcDir) YES IfInt $($ShellCode) != $(!SHELL_CODE_OK) GoTo ShellCodeError Else-IfStr(i) $($R0) == STATUS_FAILED Shell $(UtilityInf) RegistryErrorString "ASK_SOURCE_FAIL" IfInt $($ShellCode) != $(!SHELL_CODE_OK) GoTo ShellCodeError EndIf Set Error = $($R0) GoTo FatalError Else-IfStr(i) $($R0) == STATUS_USERCANCEL GoTo SuccessfulOption EndIf Set SrcDir = $($R1) EndIf Install "Install-Option" IfStr(i) $(STF_INSTALL_OUTCOME) != STF_SUCCESS Shell $(UtilityInf) RegistryErrorString "UNABLE_COPY_FILE" IfInt $($ShellCode) != $(!SHELL_CODE_OK) GoTo ShellCodeError EndIf Set Error = $($R0) GoTo FatalError EndIf EndIf Shell $(UtilityInf), AddSoftwareComponent, $(Manufacturer), + $(ProductSoftwareName), + $(ProductSoftwareName), + $(ProductSoftwareTitle), $(STF_CONTEXTINFNAME), + $(ProductSoftwareImagePath), "kernelautostart", "NDIS", {}, "",+ $(NetEventDLL) Set OEM_ABANDON_SOFTWARE = TRUE IfInt $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output $(InfName)": ShellCode error" GoTo ShellCodeError EndIf Set RegistryErrorIndex = $($R0) Set KeyProduct = $($R1) Set SoftNetRulesKey = $($R2) CloseRegKey $($R3) CloseRegKey $($R4) CloseRegKey $($R5) IfStr(i) $(RegistryErrorIndex) != NO_ERROR EndWait Debug-Output $(InfName)": Registry error: add software components" CloseRegKey $(KeyProduct) CloseRegKey $(SoftNetRulesKey) GoTo FatalRegistry EndIf Set NewValueList = {+ {SoftwareType,$(NoTitle),$(!REG_VT_SZ),$(SoftwareType)},+ {MajorVersion,$(NoTitle),$(!REG_VT_DWORD),$(ProductMajorVersion)},+ {MinorVersion,$(NoTitle),$(!REG_VT_DWORD),$(ProductMinorVersion)},+ {Title,$(NoTitle),$(!REG_VT_SZ),$(ProductSoftwareTitle)},+ {Description,$(NoTitle),$(!REG_VT_SZ),$(ProductSoftwareDescription)},+ {ServiceName,$(NoTitle),$(!REG_VT_SZ),$(ProductSoftwareName)},+ {InstallDate,$(NoTitle),$(!REG_VT_DWORD),*($(Now),1)}} Shell $(UtilityInf), AddValueList, $(KeyProduct), $(NewValueList) IfInt $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output $(InfName)": ShellCode error." GoTo ShellCodeError EndIf Set RegistryErrorIndex = $($R0) IfStr(i) $(RegistryErrorIndex) != NO_ERROR EndWait Debug-Output $(InfName)": Registry error: add value list." CloseRegKey $(KeyProduct) CloseRegKey $(SoftNetRulesKey) GoTo FatalRegistry EndIf Set NewValueList = {+ {type,$(NoTitle),$(!REG_VT_SZ),$(NetRuleSoftwareType)},+ {use,$(NoTitle),$(!REG_VT_SZ),$(NetRuleSoftwareUse)}, + {bindform,$(NoTitle),$(!REG_VT_SZ),$(NetRuleSoftwareBindForm)}, + {class,$(NoTitle),$(!REG_VT_MULTI_SZ),$(NetRuleSoftwareClass)}, + {bindable,$(NoTitle),$(!REG_VT_MULTI_SZ),$(Bindable$(Option)Txt)}, + {InfOption,$(NoTitle),$(!REG_VT_SZ),$(Option)}} Shell $(UtilityInf), AddValueList, $(SoftNetRulesKey), $(NewValueList) IfInt $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output $(InfName)": ShellCode error." GoTo ShellCodeError EndIf Set RegistryErrorIndex = $($R0) CloseRegKey $(KeyProduct) CloseRegKey $(SoftNetRulesKey) IfStr(i) $(RegistryErrorIndex) != NO_ERROR EndWait Debug-Output $(InfName)": Resgitry error: add value list." GoTo FatalRegistry EndIf EndIf Shell $(UtilityInf), AddHardwareComponent, $(ProductHardwareName),$(STF_CONTEXTINFNAME),$(ProductKeyName) IfInt $($R4) != -1 Set OEM_ABANDON_OPTIONS = >($(OEM_ABANDON_OPTIONS), $(!NTN_SoftwareBase)"\Microsoft\Windows NT\CurrentVersion\NetworkCards\"$($R4)) EndIf IfInt $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output $(InfName)": Cannot add hardware component" GoTo ShellCodeError EndIf Set RegistryErrorIndex = $($R0) IfStr(i) $(RegistryErrorIndex) != NO_ERROR EndWait Debug-Output $(InfName)": Registry error: add hardware component" CloseRegKey $($R1) CloseRegKey $($R2) CloseRegKey $($R3) GoTo FatalRegistry EndIf Set KeyParameters = $($R3) Set KeyAdapterRules = $($R2) Set AdapterNumber = $($R4) Set NewValueList = {+ {Manufacturer,$(NoTitle),$(!REG_VT_SZ),$(Manufacturer)},+ {Title,$(NoTitle),$(!REG_VT_SZ),"["$($R4)"] "$(ProductHardware$(Option)Title)},+ {Description,$(NoTitle),$(!REG_VT_SZ),$(ProductHardware$(Option)Description)},+ {ProductName,$(NoTitle),$(!REG_VT_SZ),$(ProductHardwareName)},+ {ServiceName,$(NoTitle),$(!REG_VT_SZ),$($R5)},+ {InstallDate,$(NoTitle),$(!REG_VT_DWORD),*($(Now),1)}} Shell $(UtilityInf), AddValueList, $($R1), $(NewValueList) IfInt $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output $(InfName)": ShellCode error" GoTo ShellCodeError EndIf CloseRegKey $($R1) Set TempProdName = """"$(ProductHardwareName)$(AdapterNumber)"""" Set TempBindForm = $(TempProdName)$(NetRuleHardwareBindForm) Set NewValueList = {+ {type,$(NoTitle),$(!REG_VT_SZ),$(NetRuleHardware$(Option)Type)},+ {bindform,$(NoTitle),$(!REG_VT_SZ),$(TempBindForm)}, + {class,$(NoTitle),$(!REG_VT_MULTI_SZ),$(NetRuleHardware$(Option)Class)}, + {InfOption,$(NoTitle),$(!REG_VT_SZ),$(Option)}} Shell $(UtilityInf), AddValueList, $(KeyAdapterRules), $(NewValueList) IfInt $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output $(InfName)": ShellCode error." GoTo ShellCodeError EndIf Set RegistryErrorIndex = $($R0) IfStr(i) $(RegistryErrorIndex) != NO_ERROR EndWait Debug-Output $(InfName)": Resgitry error: add value list." CloseRegKey $(KeyParameters) CloseRegKey $(KeyAdapterRules) GoTo FatalRegistry EndIf CloseRegKey $(KeyAdapterRules) GoTo WriteParameters ;*********************************************************************** ; ;*********************************************************************** WriteParameters = + Debug-Output $(InfName)": Open the dialog box for user input" Debug-Output $(InfName)": cfgResult = "$(cfgResult) Debug-Output $(InfName)": SwithType = "$(Line0.SwitchType) Debug-Output $(InfName)": Ch0.Phone = "$(Line0.Channel0.Phone) Debug-Output $(InfName)": Ch0.SPID = "$(Line0.Channel0.SPID) Debug-Output $(InfName)": Ch1.Phone = "$(Line0.Channel1.Phone) Debug-Output $(InfName)": Ch1.SPID = "$(Line0.Channel1.SPID) set BoardName = "WB692PCI" set NumberofLines = 1 Debug-Output $(InfName)": AdapterNumber = "$(AdapterNumber) IfStr(i) $(!NTN_InstallMode) == install Set TapiAddressList = {$(AdapterNumber)" 1 0"} IfStr(i) $(Option) == WB692PCI Set TapiAddressList = >($(TapiAddressList),$(AdapterNumber)" 2 0") EndIf Else Debug-Output $(InfName)": TapiAddressList = "$(TapiAddressList) EndIf Set BusType = 5 Set NewValueList = {+ {BusType,$(NoTitle),$(!REG_VT_DWORD),$(BusType)},+ {BusNumber,$(NoTitle),$(!REG_VT_DWORD),$(BusNumber)},+ {SlotNumber,$(NoTitle),$(!REG_VT_DWORD),$(SlotNumber)},+ {FunctionNumber,$(NoTitle),$(!REG_VT_DWORD),$(FunctionNumber)},+ {BoardName,$(NoTitle),$(!REG_VT_SZ),$(BoardName)},+ {DeviceName,$(NoTitle),$(!REG_VT_SZ),$(ProductHardwareName)},+ {AddressList,$(NoTitle),$(!REG_VT_MULTI_SZ),$(TapiAddressList)},+ {MediaType,$(NoTitle),$(!REG_VT_SZ),$(TapiMediaType)},+ {NumberofLines,$(NoTitle),$(!REG_VT_DWORD),$(NumberofLines)},+ } Shell $(UtilityInf), AddValueList, $(KeyParameters), $(NewValueList) CloseRegKey $(KeyParameters) IfInt $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output $(InfName)": ShellCode error." GoTo ShellCodeError EndIf Set RegistryErrorIndex = $($R0) IfStr(i) $(RegistryErrorIndex) != NO_ERROR Debug-Output $(InfName)": Registry error: Add value list" GoTo FatalRegistry EndIf IfStr(i) $(!NTN_InstallMode) == configure Debug-Output $(InfName)": Configuration is done" GoTo SuccessfulOption EndIf OpenRegKey $(!REG_H_LOCAL) "" "HARDWARE\DEVICEMAP" $(MAXIMUM_ALLOWED) BaseKey shell "" WbCreateRegKey $(BaseKey) "TAPI DEVICES\WB692PCI" IfStr(i) $($R0) != NO_ERROR Debug-Output $(InfName)": Error creating registry key!" GoTo FatalRegistry EndIf Set TapiDeviceKey = $($R1) Set NewValueList = {+ {Address,$(NoTitle),$(!REG_VT_MULTI_SZ),$(TapiAddressList)},+ {"Media Type",$(NoTitle),$(!REG_VT_SZ),$(TapiMediaType)}} Shell $(UtilityInf), AddValueList, $(TapiDeviceKey), $(NewValueList) IfInt $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output $(InfName)": ShellCode error." GoTo ShellCodeError EndIf Set RegistryErrorIndex = $($R0) IfStr(i) $(RegistryErrorIndex) != NO_ERROR Debug-Output $(InfName)": Registry error: Add value list" GoTo FatalRegistry EndIf CloseRegKey $(TapiDeviceKey) CloseRegKey $(BaseKey) Read-Syms InvokeRasDlg$(!STF_LANGUAGE) Shell "oemnsvra.inf" CheckRasInstalled IfInt $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output $(InfName)": Error Shelling the RAS INF file oemnsvra.inf" Shell "subroutn.inf" SetupMessage, $(!STF_LANGUAGE), + "STATUS", $(InvokeRasError) IfInt $($ShellCode) != $(!SHELL_CODE_OK) GoTo ShellCodeError EndIf GoTo SuccessfulOption EndIf Set RasInstalled = $($R0) Debug-Output $(InfName)": Is RAS Installed? "$(RasInstalled) IfStr(i) $(RasInstalled) == FALSE Shell "subroutn.inf" SetupMessage, $(!STF_LANGUAGE), "STATUS", + $(InvokeRasSetupMsg) IfInt $($ShellCode) != $(!SHELL_CODE_OK) GoTo SuccessfulOption EndIf Else Shell "subroutn.inf" SetupMessage, $(!STF_LANGUAGE), "STATUS", + $(InvokeRasConfigMsg) IfInt $($ShellCode) != $(!SHELL_CODE_OK) GoTo SuccessfulOption EndIf EndIf IfStr(i) $(!STF_IDW) == TRUE Set AddCopy = NO Set DoCopy = NO Set DoConfig = NO Else Set AddCopy = YES Set DoCopy = YES Set DoConfig = YES EndIf Set SaveNTN_InstallMode = $(!NTN_InstallMode) IfStr(i) $(RasInstalled) == TRUE Set !NTN_InstallMode = configure Else Set !NTN_InstallMode = install EndIf set SaveSTF_SRCDIR_OVERRIDE = $(!STF_SRCDIR_OVERRIDE) set !STF_SRCDIR_OVERRIDE = "" Debug-Output $InfName)": STF_LANGUAGE = "$(!STF_LANGUAGE) Debug-Output $InfName)": RasDir = "$(RasDir) Debug-Output $InfName)": AddCopy = "$(AddCopy) Debug-Output $InfName)": DoCopy = "$(DoCopy) Debug-Output $InfName)": DoConfig = "$(DoConfig) Shell "oemnsvra.inf" InstallOption $(!STF_LANGUAGE) "RAS" $(RasDir) $(AddCopy) $(DoCopy) $(DoConfig) set !NTN_InstallMode = $(SaveNTN_InstallMode) set !STF_SRCDIR_OVERRIDE = $(SaveSTF_SRCDIR_OVERRIDE) IfInt $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output $(InfName)": Error Shelling the RAS INF file oemnsvra.inf" Shell "subroutn.inf" SetupMessage, $(!STF_LANGUAGE), "STATUS", + $(InvokeRasError) IfInt $($ShellCode) != $(!SHELL_CODE_OK) GoTo ShellCodeError EndIf GoTo SuccessfulOption EndIf SkipRasSetup =+ EndWait GoTo SuccessfulOption ;*********************************************************************** ; ;*********************************************************************** BindingAdapter =+ Set Error = "Binding: Sorry, not yet implemented." GoTo FatalError ;*********************************************************************** ; ;*********************************************************************** RemoveAdapter = + IfStr(i) $(ProductKeyName) == $(!NTN_RegBase) Shell $(UtilityInf), RemoveSoftwareComponent, $(Manufacturer), + $(ProductSoftwareName) IfInt $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output $(InfName)": ShellCode error" GoTo ShellCodeError EndIf Set RegistryErrorIndex = $($R0) IfStr(i) $(RegistryErrorIndex) != NO_ERROR GoTo FatalRegistry EndIf Else Shell $(UtilityInf), RemoveHardwareComponent, $(Manufacturer), + $(ProductSoftwareName), $(!NTN_RegBase) IfInt $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output $(InfName)": ShellCode error" GoTo ShellCodeError EndIf Set RegistryErrorIndex = $($R0) IfStr(i) $(RegistryErrorIndex) != NO_ERROR GoTo FatalRegistry EndIf EndIf GoTo end ;*********************************************************************** ; ;*********************************************************************** UpgradeSoftware = + IfStr(i) $(ProductKeyName) == $(!NTN_RegBase) OpenRegKey $(!REG_H_LOCAL) "" $(ProductKeyName) $(MAXIMUM_ALLOWED) KeyProduct IfStr $(KeyProduct) != $(KeyNull) GetRegValue $(KeyProduct),"MajorVersion", VersionInfo Set Version = *($(VersionInfo), 4) Shell $(UtilityInf), GetInfFileNameFromRegistry, $(KeyProduct) IfInt $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output $(InfName)": ShellCode error" GoTo ShellCodeError EndIf Set !UG_Filename = $($R0) IfStr(i) $(!UG_Filename) != "" install "Install-Update" IfStr(i) $(STF_INSTALL_OUTCOME) != STF_SUCCESS GoTo FatalError EndIf EndIf SetRegValue $(KeyProduct) {MajorVersion,$(NoTitle),$(!REG_VT_SZ),$(ProductMajorVersion)} SetRegValue $(KeyProduct) {MinorVersion,$(NoTitle),$(!REG_VT_SZ),$(ProductMinorVersion)} IfInt $(Version) != $(ProductVersion) EndIf CloseRegKey $(KeyProduct) Else GoTo FatalRegistry EndIf Else OpenRegKey $(!REG_H_LOCAL) "" $(!NTN_RegBase) + $(MAXIMUM_ALLOWED) NetworkCardKey IfStr(i) $(NetworkCardKey) != $(KeyNull) GetRegValue $(NetworkCardKey),"ServiceName", ServiceNameInfo Set ServiceName = *($(ServiceNameInfo), 4) OpenRegKey $(NetworkCardKey) "" "NetRules" + $(MAXIMUM_ALLOWED) NetRuleKey IfStr(i) $(NetRuleKey) != $(KeyNull) Else GoTo FatalRegistry EndIf CloseRegKey $(NetRules) CloseRegKey $(NetworkCardKey) Else GoTo FatalRegistry EndIf OpenRegKey $(!REG_H_LOCAL) "" + $(!NTN_ServiceBase)"\"$(ServiceName) + $(MAXIMUM_ALLOWED) ServiceKey IfStr(i) $(ServiceKey) != $(KeyNull) CloseRegKey $(ServiceKey) Else GoTo FatalRegistry EndIf EndIf GoTo end ;*********************************************************************** ; ;*********************************************************************** SuccessfulOption = + GoTo end ;*********************************************************************** ; ;*********************************************************************** Abandon = + ForListDo $(OEM_ABANDON_OPTIONS) Shell $(UtilityInf), RemoveHardwareComponent, $(Manufacturer), + $(ProductSoftwareName), $($) IfInt $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output $(InfName)": ShellCode error" GoTo ShellCodeError EndIf Set RegistryErrorIndex = $($R0) IfStr(i) $(RegistryErrorIndex) != NO_ERROR GoTo FatalRegistry EndIf EndForListDo IfStr(i) $(OEM_ABANDON_SOFTWARE) == TRUE Shell $(UtilityInf), RemoveSoftwareComponent, $(Manufacturer), + $(ProductSoftwareName), FALSE IfInt $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output $(InfName)": ShellCode error" GoTo ShellCodeError EndIf Set RegistryErrorIndex = $($R0) IfStr(i) $(RegistryErrorIndex) != NO_ERROR GoTo FatalRegistry EndIf EndIf GoTo end ;*********************************************************************** ; ;*********************************************************************** WarningMsg = + Shell $(subroutineinf) SetupMessage, $(!STF_LANGUAGE), "WARNING", $(Error) IfInt $($ShellCode) != $(!SHELL_CODE_OK) GoTo ShellCodeError EndIf IfStr(i) $($R1) == "OK" GoTo $(to) Else-IfStr(i) $($R1) == "CANCEL" GoTo $(from) EndIf GoTo end ;*********************************************************************** ; ;*********************************************************************** NonFatalInfo = + Set Severity = STATUS Set CommonStatus = STATUS_USERCANCEL IfStr(i) $(Error) == "" Set Severity = NONFATAL Shell $(UtilityInf) RegistryErrorString "SETUP_FAIL" IfInt $($ShellCode) != $(!SHELL_CODE_OK) GoTo ShellCodeError EndIf Set Error = $($R0) EndIf Shell $(subroutineinf) SetupMessage, $(!STF_LANGUAGE), $(Severity), $(Error) IfInt $($ShellCode) != $(!SHELL_CODE_OK) GoTo ShellCodeError EndIf IfStr(i) $($R1) == "OK" GoTo $(from) EndIf GoTo end ;*********************************************************************** ; ;*********************************************************************** FatalRegistry = + Shell $(UtilityInf) RegistryErrorString $(RegistryErrorIndex) IfInt $($ShellCode) != $(!SHELL_CODE_OK) GoTo ShellCodeError EndIf Set Error = $($R0) GoTo FatalError ;*********************************************************************** ; ;*********************************************************************** FatalDetect = + Shell $(UtilityInf),RegistryErrorString,CANNOT_DETECT IfInt $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output $(InfName)": ShellCode error: cannot get an error string." GoTo ShellCodeError EndIf Set Error = $($R0) GoTo FatalError ;*********************************************************************** ; ;*********************************************************************** FatalError = + IfStr(i) $(Error) == "" Shell $(UtilityInf) RegistryErrorString "SETUP_FAIL" IfInt $($ShellCode) != $(!SHELL_CODE_OK) GoTo ShellCodeError EndIf Set Error = $($R0) EndIf Shell $(subroutineinf) SetupMessage, $(!STF_LANGUAGE), "FATAL", $(Error) IfInt $($ShellCode) != $(!SHELL_CODE_OK) GoTo ShellCodeError EndIf GoTo SetFailed ;*********************************************************************** ; ;*********************************************************************** ShellCodeError = + Set DlgType = "MessageBox" Set STF_MB_TITLE = $(ShellCodeErrorTitle) Set STF_MB_TEXT = $(ShellCodeErrorText) Set STF_MB_TYPE = 1 Set STF_MB_ICON = 3 Set STF_MB_DEF = 1 UI Start "Error Message" GoTo SetFailed ;*********************************************************************** ; ;*********************************************************************** SetFailed = + Set CommonStatus = STATUS_FAILED IfStr(i) $(OEM_ABANDON_ON) == TRUE Set OEM_ABANDON_ON = FALSE GoTo Abandon EndIf GoTo end ;*********************************************************************** ; ;*********************************************************************** end = + Return $(CommonStatus) ;*********************************************************************** ; ;*********************************************************************** [WbCreateRegKey] Debug-Output $(InfName)": Entering [WbCreateRegKey]" Set ECR_Result = NO_ERROR Set ECR_BaseKeyHandle = $($0) Set ECR_NewPath = $($1) Set KeyNull = "" Set MAXIMUM_ALLOWED = 33554432 Debug-Output $(InfName)": WbCreateRegKey - ECR_BaseKeyHandle ="$(ECR_BaseKeyHandle) Debug-Output $(InfName)": ECR_NewPath = "$(ECR_NewPath) Debug-Output $(InfName)": MAXIMUM_ALLOWED = "$(MAXIMUM_ALLOWED) Debug-Output $(InfName)": KeyNull = "$(KeyNull) OpenRegKey $(ECR_BaseKeyHandle) "" $(ECR_NewPath) $(MAXIMUM_ALLOWED) + ECR_BaseKey Debug-Output $(InfName)": ECR_BaseKey = "$(ECR_BaseKey) Debug-Output $(InfName)": OpenRegKey returned "$($R0) IfStr $(ECR_BaseKey) == $(KeyNull) Debug-Output $(InfName)": ECR_BaseKey == KeyNull" Else Debug-Output $(InfName)": ECR_BaseKey != KeyNull" Set ECR_KeyHandle = $(ECR_BaseKey) GoTo ECR_Return EndIf Set ECR_TmpPath = "" Split-String $(ECR_NewPath) "\" ECR_PList Debug-Output $(InfName)": ECR_PList = "$(ECR_PList) ForListDo $(ECR_PList) IfStr(i) $($) != "\" IfInt $(#) == 1 Set ECR_TmpPath = $($) Else Set ECR_TmpPath = $(ECR_TmpPath)"\"$($) EndIf Debug-Output $(InfName)": Determining if "$(ECR_TmpPath)" exists" OpenRegKey $(ECR_BaseKeyHandle) "" $(ECR_TmpPath) $(MAXIMUM_ALLOWED) ECR_BaseKey IfStr $(ECR_BaseKey) == $(KeyNull) Debug-Output $(InfName)": Creating "$(ECR_TmpPath) CreateRegKey $(ECR_BaseKeyHandle) {$(ECR_TmpPath),0,GenericClass} "" $(MAXIMUM_ALLOWED) "" ECR_KeyHandle IfStr(i) $(ECR_KeyHandle) == $(KeyNull) Set ECR_Result = $($R0) GoTo ECR_Return EndIf EndIf EndIf EndForListDo ECR_Return = + Return $(ECR_Result) $(ECR_KeyHandle) ;*********************************************************************** ; ;*********************************************************************** [DebugConfiguration] Debug-Output $(!p:InfName)": **CONFIGURATION STATE: "$($0) Return ;*********************************************************************** ; ;*********************************************************************** [Install-Option] Set STF_VITAL = "" IfStr(i) $(AddCopy) == "YES" AddSectionFilesToCopyList Files-$(Option) $(SrcDir) $(!STF_WINDOWSSYSPATH)\drivers EndIf IfStr(i) $(DoCopy) == "YES" Set !STF_NCPA_FLUSH_COPYLIST = TRUE CopyFilesInCopyList EndIf Exit ;*********************************************************************** ; ;*********************************************************************** [Install-Update] Set STF_VITAL = "" Set STF_OVERWRITE = "VERIFYSOURCEOLDER" AddSectionFilesToCopyList Files-$(Option) $(SrcDir) $(!STF_WINDOWSSYSPATH)\drivers AddSectionFilesToCopyList Files-Inf $(SrcDir) $(!STF_WINDOWSSYSPATH) Set !STF_NCPA_FLUSH_COPYLIST = TRUE CopyFilesInCopyList Exit ;*********************************************************************** ; ;*********************************************************************** [Source Media Descriptions] ; 1 = "Winbond W6692 ISDN PCI cardWindow NT Setup Disk" , TAGFILE = WB692PCI.SYS 1 = "Winbond W6692 ISDN PCI cardWindow NT Setup Disk" ;*********************************************************************** ; ;*********************************************************************** [ProductType] STF_PRODUCT = Winnt STF_PLATFORM = I386 ;*********************************************************************** ; ;*********************************************************************** [Files-Inf] 1, oemsetnt.inf, SIZE=46000, RENAME=$(!UG_Filename) ;*********************************************************************** ; ;*********************************************************************** [Files-WB692PCI] 1, WB692PCI.SYS, SIZE=383000 ;*********************************************************************** ;*********************************************************************** ;*********************************************************************** ; ;*********************************************************************** [LanguagesSupported] ENG ;*********************************************************************** ; ;*********************************************************************** [OptionsTextENG] WB692PCI = "Winbond ISDN PCI CARD" ;*********************************************************************** ; ;*********************************************************************** [FileConstantsENG] ProCaption = "Windows NT Setup" ProCancel = "Cancel" ProCancelMsg = "Windows NT Networking is not correctly installed. "+ "Are you sure you want to cancel copying files?" ProCancelCap = "Network Setup Message" ProText1 = "Copying:" ProText2 = "To:" FunctionTitleWB692PCI = "Winbond ISDN PCI Card Setup" ProductSoftwareDescription = "Winbond ISDN PCI CARD Driver" ProductHardwareWB692PCIDescription = "Winbond ISDN PCI CARD" ProductSoftwareTitle = "Winbond ISDN PCI CARD Driver" ProductHardwareWB692PCITitle = "Winbond ISDN PCI CARD" ShellCodeErrorTitle = "Error: "$(FunctionTitle)$(Option)) ShellCodeErrorText = "Shell Code Error." CANNOT_FIND_ANY_CARD = "Network card is not present in the system" ;*********************************************************************** ; ;*********************************************************************** [DialogConstantsENG] Help = "&Help" Exit = "Cancel" OK = "OK" HelpContext = "" Continue = "Continue" Cancel = "Cancel" ;*********************************************************************** ; ;*********************************************************************** [FileDependentDlgENG] DlgType = "RadioCombination" DlgType = "Edit" DlgType = "Radio" DlgTemplate = "NE2000" Caption = $(FunctionTitle)$(Option) Combo1List = $(MASTER_List) Combo1Out = $(MasterEnable) Combo2List = $(IO_Hex_List) Combo2Out = $(IO_Hex_Value) ComboListItemsIn = {Combo1List, Combo2List} ComboListItemsOut = {Combo1Out, Combo2Out} EditTextIn = "12345" EditTextLim = "987654321" CBOptionsGreyed = {} NotifyFields = {NO, NO} ; HelpContext = $(!IDH_DB_OEMNADN2_INS) ;*********************************************************************** ; ;*********************************************************************** [InvokeRasDlgENG] InvokeRasSetupMsg = "Winbond ISDN PCI card setup is complete. "+ "Remote Access Services (RAS) will now be installed. "+ "Please configure the ISDN ports in RAS "+ "setup to enable you to use RAS over the ISDN." InvokeRasConfigMsg = "Winbond ISDN PCI card setup is complete. "+ "Remote Access Services (RAS) setup will now be invoked. "+ "Please configure one or more ISDN ports in RAS "+ "setup to enable you to use RAS over the ISDN." InvokeRasError = "Winbond ISDN PCI card setup encountered an error "+ "while invoking the RAS setup INF file (OEMNSVRA.INF). "+ "Please make sure that the file is present in the "+ "System32 directory and is the proper file."Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.