1. Pcmcia.zip Driver
2. WFW311.TXT File Contents

WFW311.TXT Driver File Contents (Pcmcia.zip)

Before you start with the installation process, make sure that
the Card Manager software has been successfully installed. For
information on installing the Card Manager software, please refer
to the appropriate readme file, your Ethernet Adapter manual, or
your computer manufacturer.

Follow the procedure below to run the PCMCIA/CT II card with Microsoft's
Windows for Workgroups(WFW311). This shows how to run WFW311 with the NE2000
driver(or PCM200 driver).

3)Installing either the NE2000 Compatible driver or the PCM200 driver.
  Method 1:
    Running WFW with the NE2000 Compatible driver.
    =================================================
    WINDOWS FOR WORKGROUPS 3.11

    1. Select NETWORK SETUP program item from program group NETWORK.
    2. Select DRIVERS button.
    3. Select ADD ADAPTER button.
    4. Select NE2000 Compatible NETWORK ADAPTER from adapter menu and choose OK
       button.
    5. Select CLOSE button to end the DRIVERS setup.
    6. Select OK button to end the NETWORK setup.

  Method 2:
    Running WFW with the PCM200 driver.
    =======================================

    The OEMSETUP.INF file allow you to run Microsoft Windows for Workgroups
    with the PCMCIA/CT II Ethernet LAN Adapter. The installation procedure is
    as fellows:

    WINDOWS FOR WORKGROUPS 3.11

    1. Select NETWORK SETUP program item from program group NETWORK.
    2. Select DRIVERS button.
    3. Select ADD ADAPTER button.
    4. Select UNLISTED OR UPDATED NETWORK ADAPTER from adapter menu and choose
       OK button.
    5. Insert disk contains PCM200.DOS, PCM200.386 and OEMSETUP.INF in driver.
    6. Specify the path (A:\WFW311) and choose OK button.
    7. Select "PCMCIA/CT II Ethernet" from adapter menu and choose OK button.
    8. Select CLOSE button to end the DRIVERS setup.
    9. Select OK button to end the NETWORK setup.


4) Exit Windows for Workgroups and reboot your PC.

This completes the Windows for Workgroups installation.


Before installing the PCMCIA/CT II Ethernet LAN into workstation, you
have to append the following lines into config.sys and autoexec.bat
file or it would look like the following.

     < Sample CONFIG.SYS file >

	   DEVICE=C:\DOS\SETVER.EXE
	   DEVICE=C:\WFW311\HIMEM.SYS
	   DEVICE=C:\DOS\EMM386.EXE X=D000-D0FF RAM NOEMS
	   DOS=HIGH,UMB
	   FILES=30
	   BUFFERS=20
	   REM CardSoft(TM) 3.1 PCMCIA DRIVERS
	   DEVICEHIGH=C:\CARDSOFT\SS365SL.EXE
	   DEVICEHIGH=C:\CARDSOFT\CS.EXE  /POLL:1
	   DEVICEHIGH=C:\CARDSOFT\CSALLOC.EXE
	   DEVICEHIGH=C:\CARDSOFT\CARDID.EXE
	   DEVICEHIGH=C:\CARDSOFT\ECARDCS.EXE /IRQ=5 /IO=300
	   STACKS=9,256
	   DEVICE=C:\WINDOWS\IFSHLP.SYS
	   LASTDRIVE=Z

     < Sample AUTOEXEC.BAT file >

	   @ECHO OFF
	   PROMPT $p$g
	   PATH C:\WINDOWS;
	   SET TEMP=C:\WINDOWS\TEMP
	   C:\WINDOWS\SMARTDRV.EXE
	   C:\WINDOWS\NET START

	   =========================

	   CALL C:\NET\ODI\STARTNET.BAT 	; only for ODI driver
	   C:\WINDOWS\ODIHLP			; only for ODI driver


     < Sample STARTNET.BAT file >

	   CD \NET\ODI
	   SET NWLANGUAGE=ENGLISH
	   LSL
	   PCM200
	   IPXODI /A
	   VLM
	   CD \


     < Sample NET.CFG file >

	   LINK SUPPORT
		   BUFFERS 8 1514
	   Max Boards 4
	   Max Boards 4

	   Link Driver PCM200
		   PORT 300
		   INT 5
		   Frame Ethernet_802.2
		   Frame Ethernet_802.3
	   NetWare DOS Requester
		   FIRST NETWORK DRIVE = F
	   PB BUFFERS=3

     < Sample PROTOCOL.INI file >

	   [network.setup]
	   version=0x3110
	   netcard=PCM200,1,PCM200,3
	   transport=ms$nwlinknb,NWLINK
	   transport=ms$ndishlp,MS$NDISHLP
	   transport=ms$netbeui,NETBEUI
	   lana0=PCM200,1,ms$netbeui
	   lana1=PCM200,1,ms$nwlinknb
	   lana2=PCM200,1,ms$ndishlp


	   [protman]
	   DriverName=PROTMAN$
	   PRIORITY=MS$NDISHLP

	   [PCM200]
	   DriverName=PCM200$
	   Adapters=PCM200
	   IOBASE=0x300
	   INTERRUPT=5

	   [NWLINK]

	   BINDINGS=PCM200
	   [MS$NDISHLP]
	   DriverName=ndishlp$
	   BINDINGS=PCM200

	   [NETBEUI]
	   DriverName=netbeui$
	   SESSIONS=10
	   NCBS=12
	   BINDINGS=PCM200
	   LANABASE=0


How To Update Drivers Manually

After your driver has been downloaded, follow these simple steps to install it.

• Expand the archive file (if the download file is in zip or rar format).

• If the expanded file has an .exe extension, double click it and follow the installation instructions.

• Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.

• Find the device and model you want to update in the device list.

• Double-click on it to open the Properties dialog box.

• From the Properties dialog box, select the Driver tab.

• Click the Update Driver button, then follow the instructions.

Very important: You must reboot your system to ensure that any driver updates have taken effect.

For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.