1. Pcmcia.zip Driver
2. WFW31.TXT File Contents

WFW31.TXT Driver File Contents (Pcmcia.zip)

Before you start with the installation process, make sure that
the Card Manager software has been successfully installed. For
information on installing the Card Manager software, please refer
to the appropriate readme file, your Ethernet Adapter manual, or
your computer manufacturer.

Follow the procedure below to run the PCMCIA/CT II card with Microsoft's
Windows for Workgroups(WFW31). This shows how to run WFW31 with the NE2000
driver(or PCM200 driver).

3)Installing either the NE2000 Compatible driver or the PCM200 driver.
  Method 1:
    Running WFW with the NE2000 Compatible driver.
    =================================================
    WINDOWS FOR WORKGROUPS 3.1

    1. Select NETWORK program item from program group CONTROL PANEL.
    2. Select ADAPTERS from the OPTIONS menu.
    3. Select ADD button.
    4. Select NE2000 Compatible NETWORK ADAPTER from adapter menu and choose
       OK button.
    5. Choose OK button when asked to configured the adapter.
    6. Select CLOSE button to end the ADAPTER setup.
    7. Select OK to end NETWORK setup.

  Method 2:
    Running WFW with the PCM200 driver.
    =======================================

    The OEMSETUP.INF file allow you to run Microsoft Windows for Workgroups
    with the PCMCIA/CT II Ethernet Adapter. The installation procedure is
    as fellows:

    WINDOWS FOR WORKGROUPS 3.1

    1. Select NETWORK program item from program group CONTROL PANEL.
    2. Select ADAPTERS from the OPTIONS menu.
    3. Select ADD button.
    4. Select UNLISTED OR UPDATED NETWORK ADAPTER from adapter menu and choose
       OK button.
    5. Insert disk contains PCM200.DOS and OEMSETUP.INF in driver.
    6. Sperify the path (A:\WFW31) and choose OK button.
    7. Select "PCMCIA/CT II Ethernet" from adapter menu and choose OK button.
    8. Choose OK button when asked to configured the adapter.
    9. Select CLOSE button to end the ADAPTER setup.
    10.Select OK to end NETWORK setup.

4) Exit Windows for Workgroups and reboot your PC.

This completes the Windows for Workgroups installation.

Before installing the PCMCIA/CT II Ethernet LAN into workstation, you
have to append the following lines into config.sys and autoexec.bat
file or it would look like the following.

     < Sample CONFIG.SYS file >

	   DEVICE=C:\DOS\SETVER.EXE
	   DEVICE=C:\DOS\HIMEM.SYS
	   DEVICE=C:\DOS\EMM386.EXE X=D000-D0FF RAM NOEMS
	   DOS=HIGH,UMB
	   FILES=30
	   BUFFERS=20
	   REM CardSoft(TM) 3.1 PCMCIA DRIVERS
	   DEVICEHIGH=C:\CARDSOFT\SS365SL.EXE
	   DEVICEHIGH=C:\CARDSOFT\CS.EXE  /POLL:1
	   DEVICEHIGH=C:\CARDSOFT\CSALLOC.EXE
	   DEVICEHIGH=C:\CARDSOFT\CARDID.EXE
	   DEVICEHIGH=C:\CARDSOFT\ECARDCS.EXE /IRQ=5 /IO=300
	   STACKS=9,256
	   DEVICE=C:\WINDOWS\protman.dos /i:C:\WINDOWS
	   DEVICE=C:\WINDOWS\pcm200.dos
	   DEVICE=C:\WINDOWS\workgrp.sys
	   LASTDRIVE=Z

     < Sample AUTOEXEC.BAT file >

	   @ECHO OFF
	   PROMPT $p$g
	   PATH C:\WINDOWS;
	   SET TEMP=C:\WINDOWS\TEMP
	   C:\WINDOWS\NET START

     < Sample PROTOCOL.INI file >

	   [network.setup]
	   version=0x3100
	   netcard=PCM200,1,PCM200
	   transport=ms$netbeui,MS$NETBEUI
	   lana0=PCM200,1,ms$netbeui

	   [protman]
	   DriverName=PROTMAN$
	   PRIORITY=MS$NETBEUI

	   [MS$NETBEUI]
	   DriverName=netbeui$
	   SESSIONS=10
	   NCBS=32
	   BINDINGS=PCM200
	   LANABASE=0


	   [PCM200]
	   DriverName=PCM200$
	   IOBASE=0x300
	   INTERRUPT=5