Workstation for DOS ODI Client
Introduction:
-------------
This document describes the procedure to setup the NetWare v3.X, v4.X
workstation driver for PCMCIA/CT II Ethernet adapter.
Location of Driver: \NETWARE\PCM200.COM
Setup Procedures for NetWare 3.11/3.12 Client :
-----------------------------------------------
Before you start with the installation process, make sure that
the Card Manager software has been successfully installed. For
information on installing the Card Manager software, please refer
to the appropriate readme file, your Ethernet Adapter manual, or
your computer manufacturer.
1. Copy PCM200.COM from the PCMCIA/CT II Driver Diskette subdirectory
A:\NETWARE to your harddisk.
2. Create a batch file, or add to your STARTNET.BAT file the commands
listed above under STARTNET.BAT
3. Edit the NET.CFG file that you copied over. Edit the file per your
requirements (see examples). If there are two frame types listed,
whichever frame type is listed first, that is the one that the
driver will load. See above for examples. The NET.CFG file should
be in the same directory with LSL.COM file.
Setup Procedures for NetWare 4.X Client with vlm:
-----------------------------------------------
The installation utility INSTALL.EXE is located on NetWare's
"Workstation for DOS" disk. Run INSTALL.EXE from the Workstation
for DOS Disk.
The NetWare Client Install program screen will appear. You must
complete each of the questions. These options are specific to your
needs.
1. Enter the destination directory for the NetWare Client.
(The default directory is C:\CLIENT.)
2. Gives you the option to automatically update the CONFIG.SYS
and the AUTOEXEC.BAT files or modify them at a later time manually.
3. Do you wish to install support for MS Windows ? (Y/N)
(MS Windows Subdirectory: default C:\WINDOWS)
4. Asks you to select a network driver and provide configuration
options. It uses the specifications you select to create the
file NET.CFG. Insert the PCMCIA/CT II drivers disk when prompted for
the driver disk and specify the driver path A:\NETWARE
5. Press <Enter> to install
NOTE:
-----
Be sure to add LASTDRIVE=Z to your CONFIG.SYS file for the
network mappings to work properly.
Before installing the PCMCIA/CT II Ethernet LAN into workstation, you
have to append the following lines into config.sys and autoexec.bat
file or it would look like the following.
< Sample CONFIG.SYS file >
DEVICE=C:\DOS\SETVER.EXE
DEVICE=C:\DOS\HIMEM.SYS
DEVICE=C:\DOS\EMM386.EXE X=D000-D0FF RAM NOEMS
DOS=HIGH,UMB
FILES=30
BUFFERS=20
REM CardSoft(TM) 3.1 PCMCIA DRIVERS
DEVICEHIGH=C:\CARDSOFT\SS365SL.EXE
DEVICEHIGH=C:\CARDSOFT\CS.EXE /POLL:1
DEVICEHIGH=C:\CARDSOFT\CSALLOC.EXE
DEVICEHIGH=C:\CARDSOFT\CARDID.EXE
DEVICEHIGH=C:\CARDSOFT\ECARDCS.EXE /IRQ=5 /IO=300
STACKS=9,256
LASTDRIVE=Z
< Sample AUTOEXEC.BAT file >
@ECHO OFF
PROMPT $p$g
PATH C:\DOS;C:\CLIENT;
CALL C:\CLIENT\STARTNET.BAT
< Sample STARTNET.BAT file >
CD \CLIENT
SET NWLANGUAGE=ENGLISH
LSL
PCM200
IPXODI /A
VLM
CD \
< Sample NET.CFG file >
LINK SUPPORT
BUFFERS 8 1514
Max Boards 4
Link Driver PCM200
PORT 300
INT 5
Frame Ethernet_802.2
Frame Ethernet_802.3 Sample Configuration Files:
NetWare DOS Requester ---------------------------
FIRST NETWORK DRIVE = F STARTNET.BAT:
PB BUFFERS=3 LSL
PCM200
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.