1. 441.zip Driver
2. V90WIZ.INI File Contents

V90WIZ.INI Driver File Contents (441.zip)

;;================= Example V90Wiz.INI ==== this file updated 3/10/98

[General]
FileCnt=4
ValidatorCnt=6
PostFlashCmdCnt=3
QuickCheckMode=0
BackupDone=0

[Options]
BlueScreen=1
OnePortOnly=0   ; faster testing if you set this to a modem port
ForceBackup=1    ;if 1, user can't get past the wizard page without backing up firmware
LogoBmp=Cptel.bmp
OemAbout=For use with Cptel K56flex external modems.
OemAboutWebPage=World Wide Web Site: http://www.viewcom.com.hk
OemAboutSupport=Tech Support Email: refer to Web page
OemWarn=The following operation cannot be halted.\n\nAre you sure you want to continue?
ShowAndWait=1
TimedShow=0
ShowIfItu=0
ItuOnly=0

[Files]
;-----------------------------------------------------------------------
; filename, loadOrder, Flags, friendlyName[64], Description[256]
; Flags:  LOADER or UNLOADER or FIRMWARE
;  and:   TRANS or FINAL or BKUP (BKUP is added added by program)
;
; be sure to set [General] FileCnt=
; leading spaces are stripped
;
File01=XmUL003.s37,  1, LOADER,         Firmware Loader,      FlashLoader -- loads via XModem
File02=XmDL003.s37,  1, UNLOADER,       Firmware Unloader,    Used to make Firmware backup via XModem
File03=2012s45d.s37, 2, FIRMWARE TRANS, K56flex V2.012,       Transitional K56flex Driver
File04=2083s1m.s37,  2, FIRMWARE FINAL, ITU V.90 Firmware,    V.90 Driver for Cptel external modems

[Validators]
;-----------------------------------------------------------------------
; ATI3,op,Ati3Text,ugCode,Maker,Model,Remark
; op can be:=(equals), * (contains), ! (notContains),  et.al.
; ugCode can be: UPDATABLE, TRANS, FINAL, or UNKNOWN
;
; leading spaces are stripped
; be sure to set [General] ValidatorCnt=
;
Validator01=ATI3, =, ATI3,               LOADFAULT, (Load Fault?), (Load Fault?), Maybe a modem in 'Load Fault' state
Validator02=ATI3, =, V1.100-K56_DLS,     UPDATABLE, Cptel,    VC8297V,    Original K56Flex modem I have
Validator03=ATI3, =, V1.120-K56_DLS,     UPDATABLE, Cptel,    VC8297V,    Original K56Flex modem I have
Validator04=ATI3, =, V1.200-K56_DLS,     UPDATABLE, Cptel,    VC8297V,    Original K56Flex modem I have
Validator05=ATI3, =, V2.012-K56_DLS,     TRANS,     Cptel,    VC8297V,    Been updated to Transitional K56Flex
Validator06=ATI3, =, V2.083-K56_DLS,     FINAL,     Cptel,    VC8297V,    Been updated to ITU V.90

[PostFlashCmds]
;-----------------------------------------------------------------------
; Cmd##=type,AT_Cmd_Text
; ugCode can be: BKUP, TRANS, or FINAL
; Commands send after a flashload.  Usually start these with AT
; leading spaces are stripped, max len is 128 per command; max cmds: 10
; be sure to set [General] PostFlasCmdCnt=
;
Cmd01=BKUP,AT&F&W
Cmd02=TRANS,AT&F&W
Cmd03=FINAL,AT&F&W