1. Compex.zip Driver
2. MSC30.TXT File Contents

MSC30.TXT Driver File Contents (Compex.zip)

            ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ»
            º                                                  º
            º   Microsoft DOS Client 3.0 Installation Guide    º
            º  Copyright (C) 1997 by PDS. All Rights Reserved. º
            º                                                  º
            ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ

ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³ GENERAL INFORMATION ³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ

Mircosoft DOS Client support both NDIS2 and DOS ODI drivers.

ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³ INSTALLATION GUIDE  ³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
The installation described below is for;

   Compex LinkPort/TX16 10/100 Fast Ethernet Adapter.


Microsoft DOS Client
ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ

1. NDIS2 driver Installation
   -------------------------

     a) Run SETUP in DISK1 og Microsoft Client 3.0 for DOS.

     b) When asked where the software to install, enter the location,

        e.g.            C:\MSCLIENT

     c) Select "Network adapter not shown an list below ..."

     d) The Install Driver box appears. Insert Compex driver diskette
        into floppy drive and type the path of the NDIS2 driver.
        Enter the driver location,

        e.g.            A:\NDIS2

     e) Select "Change Network Configuarion".

     f) Select "Add Protocol" and "Microsoft NetBEUI" to add NETBEUI
        protocol in.

     g) Follow the instruction to complete the rest of the installation.



2. DOS ODI Driver Installation
   ---------------------------

     a) Run SETUP in DISK1 of Microsoft Client 3.0 for DOS.

     b) When asked where the software to install, enter the location,

        e.g.            C:\MSCLIENT

     c) Select "ODI/NDIS Support Driver".

     d) Select "Change Network Configuarion".

     e) Select "Add Protocol" and "Microsoft NetBEUI" to add NETBEUI
        protocol in.

     f) Follow the instruction to complete the installation.

     g) Modify PROTOCOL.INI. Change all the lines BINDINGS=ODINSUPMAC
        to BINDINGS=CLPTX16 as shown by the arrows below.
        (there should have three lines needed to be modified).

                PROCOTOL.INI
                ------------
                [network.setup]
                version=0x3110
                netcard=odinsupmac,1,ODINSUPMAC,1
                transport=ms$nwlink,MS$NWLINK
                transport=ms$ndishlp,MS$NDISHLP
                transport=ms$netbeui,MS$NETBEUI
                lana0=odinsupmac,1,ms$nwlink
                lana1=odinsupmac,1,ms$ndishlp
                lana2=odinsupmac,1,ms$netbeui

                [MS$NWLINK]
                FRAME=ETHERNET_802.3
                DriverName=nwlink$
                BINDINGS=CLPTX16       <-----

                [protman]
                DriverName=PROTMAN$
                PRIORITY=MS$NDISHLP

                [ODINSUPMAC]        <---- can be deleted

                [MS$NDISHLP]
                DriverName=ndishlp$
                BINDINGS=CLPTX16       <-----
                [MS$NETBEUI]
                DriverName=netbeui$
                SESSIONS=10
                NCBS=12
                BINDINGS=CLPTX16       <-----
                LANABASE=1

     h)  Copy from A:\DOSODI directory the following files to
         C:\NWCLIENT directory;

              LSL.COM, ODINSUP.EXE and CLPTX16.COM

     i)  Create or copy the NET.CFG from A:\NDIS2 to C:\NWCLIENT
         Below is a sample of NET.CFG:

                NET.CFG
                -------

                PROTOCOL ODINSUP
                        Bind CLPTX16
                        BUFFERED

                Link driver CLPTX16
                        Frame Ethernet_802.2
                        Frame Ethernet_802.3
                        Frame Ethernet_II
                        Frame Ethernet_SNAP

     j) Modify AUTOEXEC.BAT. Below is a sample.

                AUTOEXEC.BAT
                ------------
                c:\NWclient\lsl
                c:\NWclient\CLPTX16
                c:\MSClient\net initialize    } These lines are added by
                C:\MSClient\nwlink            } Microsoft DOS Client
                c:\MSClient\odinsup           } during installation
                c:\MSClient\netbind           }
                c:\MSClient\net start         }

        ** Note:- Do not type in the character "}" and the message that follows
                  them. They are added to explain a point only.

     k) Installation completed.