ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ» º º º Compex LinkPort\TX16 10/100 PCMCIA Fast Ethernet º º CopyRight(c) 1998 Compex Inc. º º All rights reserved º º º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ¼ ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³ INSTALLATION GUIDE ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ This document describes the procedures for installing both NDIS2 and ODI drivers for LANtastic 6.0 in Windows For Workgroups 3.11 and DOS. 1.1) LANtastic 6.0 with Windows For Workgroups 3.11 ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ Setup ÄÄÄÄÄ a) Start Windows For Workgroups 3.11 and install a network adapter. Please refer to Windows For Workgroups 3.11 User Guide for the installation procedures of a network adapter. b) Start Windows For Workgroups 3.11 again. c) Insert LANtastic Network Software v6.0 Disk 1 into drive A. d) In File Manager, run INSTALL.EXE in the Disk 1. e) Enter an UNIQUE computer name in the Enter Computer Name box. f) Select the destination drive in the Enter Target Drive box. g) Enter the destination directory in the Enter Directory box. eg. C:\LANTASTI h) Select the additional LANtastic features in the Select All That Apply box. i) Check the installation information in the LANtastic Information Check box. If an ODI driver is required, goto step (m). j) Select the NDIS Support for Network Adapters option in the Select Network Adapter box. k) Enter the full pathname for the directory containing the NDIS 2.01 driver in the Enter NDIS Driver Directory. eg. A:\NDIS2 l) Insert Compex LinkPort/TX16 10/100 Fast Ethernet Disk 1 into the floppy drive A: m) Check the installation information in the LANtastic Final Information Check box. ** NOTE: -> If Extra Options shows Microsoft Client Novell Client or Novell Client, the Network Adapter option will be ODI Driver for Node Runner. -> If Extra Options shows Microsoft Client, the Network Adapter option will be NDIS Support for Network Adapters. Network Adapter: ODI Driver for NodeRunner n) Follow the instructions to continue the installation. 1.2) Extra Modifications for NDIS Driver Installation ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ If you install the client to Microsoft network ONLY, a NDIS driver is required. Follow the instructions here to make some modifications. a) Use any text editor to open the setup file, PROTOCOL.INI in your LANtastic home directory (eg. C:\LANTASTI) and modify it as follows. ... [NETBEUI_XIF] Drivername = NETBEUI$ <- Add this line ... b) If the hardware settings of the adapter are different from that specified in the PROTOCOL.INI, please change them correctly. c) Obtain the file, NETBEUI.EXE, from Microsoft and copy it to your LANtastic home directory (eg. C:\LANTASTI). 1.3) Extra Modifications for ODI Driver Installation ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ If you install the client to Novell network, a ODI driver is needed. Follow the instruction here to make the modifications. a) Use any text editor to open the config file, CONFIG.SYS and add the following lines. ... FILES=50 BUFFERS=32 LASTDRIVE=Z DEVICE=C:\LANTASTI\PROTMAN.DOS /I:C:\LANTASTI ... where LANTASTI refers to the directory where your LANtastic software is installed. b) Edit the setup file, STARTNET.BAT, in your LANtastic home directory (eg. C:\LANTASTI). Original STARTNET.BAT ... LOADHIGH LSL NRODI LOADHIGH ODINSUP LOADHIGH IPXODI LOADHIGH AI-NDIS BIND_TO=NRODI... ... New STARTNET.BAT ... LOADHIGH LSL CLPTX16 <--- Change LOADHIGH ODINSUP LOADHIGH IPXODI LOADHIGH AI-NDIS BIND_TO=CLTX16 <--- Change ... c) Edit the config file, NET.CFG, in your LANtastic home directory (eg. C:\LANTASTI). Original NET.CFG ... LINK DRIVER NRODI FRAME ETHERNET_802.2 ... New NET.CFG ... LINK DRIVER CLPTX16 <--- Change FRAME ETHERNET_802.2 d) Edit the protocol initialization file, PROTOCOL.INI, in your LANtastic home directory (eg. C:\LANTASTI). Original PROTOCOL.INI ... [NETBEUI_XIT] Drivername = netbeui$ ... Bindings = NRODI ... New PROTOCOL.INI ... [NETBEUI_XIT] Drivername = netbeui$ ... Bindings = CLPTX16 2.1) LANtastic 6.0 with DOS ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ a) Insert the LANtastic Network Software v6.0 Disk 1 and execute the following command:- A:\>INSTALL /DOS b) Enter an UNIQUE name in the Enter Computer Name box. c) Select the destination drive. d) Enter the destination directory in the Enter Directory box. e) Select the correct LANtastic features. f) Check the installation information. g) Modify the files as described in the section (1.1) or (1.2) accordingly.Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.