[Norsk]
README.TXT MATROX GRAPHICS INC. 2000.09.07
Matrox PowerDesk for Windows NT 4.0
Merk: Denne filen inneholder noe informasjon som er så ny at vi ikke har
rukket å oversette den til ditt språk. Vi beklager for ubeleiligheten.
Innholdsfortegnelse
===================
- Installasjon
- Versjonsbeskrivelse
- Bruke Matrox PowerDesk
- Maskinvareakselert 3D
- Merknader, problemer og begrensninger
- Matrox TV-utdata
- [English...] DualHead notes [...English]
Installering
============
[English...]
This section describes how to install the Matrox display driver for
Windows NT 4.0 (SP 5).
Note: You may need administrator rights to install certain
software. For more information, see Windows documentation.
(1) After the display driver has been copied to your hard disk:
Right-click your Windows desktop background, then click
"Properties" > "Settings" > "Display Type" > "Change" >
"Have Disk" > "Browse".
(2) Select the folder where the Matrox display driver for your
operating system (Windows NT 4.0) is located, then
click "Open" > "OK".
(3) Select the appropriate model/language name, then click
"OK" > "Yes" > "OK" > "Close" > "Close" > "Yes".
[...English]
Versjonsbeskrivelse
===================
Dette er skjermdriveren for Matrox for Windows NT.
Den støtter Microsoft Windows NT for x86-prosessorer, versjon 4.0
(Build 1381 eller senere).
Produktet inneholder:
- Skjermdriver
- Matrox PowerDesk for Windows NT 4.0
[English...]
The display driver supports up to 16 graphics chips at a time. If one of
those chips has DualHead support, the display driver supports up to 17
displays at a time. (Note: A graphics card may have more than one graphics
chip. Also, the display driver must support each model of graphics card
installed in your computer.)
[...English]
Bruke Matrox PowerDesk
======================
Endring av oppløsning, valg av skjerm og bruk av Matrox PowerDesk omhandles i
filen "online.doc". Du kan vise denne filen med WordPad.
Maksinvareakselerert 3D
=======================
Når det gjelder 3D-maskinvareakselerasjon, støtter Matrox Windows NT
4.0-skjermdriveren OpenGL-grensesnittet med to drivertyper, MCD (Mini Client
Driver) og ICD (Installable Client Driver). Grafikkortene Matrox Millennium,
Millennium II, Mystique, Mystique 220 og G100-baserte grafikkort har MCD-
støtte.
Matrox G200-baserte, G400-baserte og nyere grafikkort har ICD-støtte. (ICD har
flere muligheter for optimalisering enn MCD.)
3D-maskinvareakselerasjon har følgende begrensninger:
- For tiden er det ingen akselerasjon er tilgjengelig når flere kort er
i bruk.
- MCD støtter ikke modusene for 8bpp (256 farger) og 24bpp (16777216
farger). Maskinvareakselerasjon er tilgjengelig for modusene
16bpp (64K farger) og 32bpp (millioner av farger).
- Begrensninger i antall tilgjengelige oppløsninger må forventes. Alle
3D-modusene krever ekstra minne for å håndtere dobbeltbufring og/eller
Z-bufring, og dette fører til mindre tilgjengelig minne for
skjermvisningen.
Merknader, problemer og begrensninger
=====================================
[English...]
- Using 1280 x 800 display resolution with P1690 monitors
To use 1280 x 800 display resolution with P1690 monitors, make
sure "P1690" is selected with the Matrox "Monitor" property
sheet. To access this property sheet, click the "Matrox QuickDesk"
icon on your Windows taskbar, then click "Matrox Display
Properties" > "Monitor". For more information on monitor
selection, see the Matrox PowerDesk guide included with your
display driver.
[...English]
- Datamaskiner med mer enn én PCI-buss
Endring til en fullskjerms ledetekst eller enhver endring av modus
kan føre til krasj med blå skjerm hvis kortet er installert på en
annen PCI-buss enn buss 0. Problemet undrsøkes. Problemet kan
muligens løses ved å flytte det til et annet PCI-spor.
På noen systemer gir Windows NT melding om konflikt mellom kort
som er installert utenom PCI-broen. I dette tilfellet får ikke
miniportdriveren for Matrox Millennium tilgang til sitt eget kort.
Hvis systemet ikke finner Millennium-kortet kan du prøve å flytte
det til et annet PCI-spor.
Mange av disse problemene kan løses ved å installere Microsoft
Service Pack 3 (eller senere) for Windows NT 4.0.
- DirectDraw med virtuelle skrivebord
Enkelte DirectDraw-programmer fungerer ikke riktig med virtuelle
skrivebord. Vi anbefaler at du kjører DirectDraw-programmer på et
vanlig skrivebord.
- Skjermbeskytteren 3D-labyrint
Det kan oppstå skjermproblemer ved bruk av skjermbeskytteren "3D-
labyrint". Disse problemene kan oppstå etter installering av
Microsoft Service Pack 2 for Windows NT 4.0. Skjermproblemene synes
å være løst i Service Pack 3 (eller senere).
- Kjøre Winstone 97
Funksjonen CenterPOPUP bør deaktiveres (standardinnstillingen) ved
kjøring av Winstone 97-ytelsesprøver. Enkelte prøver
rapporterer tidsavbruddsfeil når CenterPOPUP brukes.
- Begrensninger ved flere grafikkort
Windows NT 4.0 støtter maksimalt 280 forskjellige visningsmoduser
(kombinasjoner av innstillinger for oppløsning, fargepalett og
oppdateringsfrekvens). Du kan nå denne grensen hvis du har
installert mer enn ett Matrox-grafikkort på datamaskinen.
Hvis knappen "VESA-innstillinger" er valgt i Matrox når maskinen
inneholder flere Matrox-kort, er det enda større sannsynlighet for
at du vil nå grensen for antall visningsmoduser i Windows NT 4.0.
Dette er fordi alternativet "VESA-innstillinger" støtter flere
forskjellige oppdateringsfrekvenser for hver innstiling for
skjermoppløsning og fargepalett.
Hvis det er installert flere enn ett Matrox-grafikkort på
datamaskinen, anbefaler vi at du ikke bruker alternativet "VESA-
innstillinger". Vær oppmerksom på at alternativet "VESA-
innstillinger" aktiveres hvis du angir oppdateringsfrekvensen i
Microsoft-dialogboksen "Egenskaper for Skjerm".
- 3D Studio MAX 1.2
Hvis du har problemer med å kjøre 3D Studio Max 1.2 når du bruker
Matrox HEIDI-driveren, kan du prøve å fjerne merket i
avmerkingsboksen "Bruk bussmastering" under "Generelle innstillinger".
Du får tilgang til denne avmerkingsboksen, klikk på "Start" -> "Programmer"
-> "Matrox PowerDesk" -> "Egenskaper for Matrox-skjerm" -> "Ytelse".
- 3D Studio MAX 2.0
Hvis du veksler mellom HEIDI-programvareemulering og OpenGL-
akselerasjon mens 3D Studio Max 2.0 kjører, kan det føre til at
visningsporter flimrer når du kjører animasjoner. Dette
problemet kan også oppstå hvis skjerminnstillingene (oppløsning
eller fargepalett) endres mens 3D Studio Max kjøres. Hvis du
får disse problemene, kan du prøve å lukke 3D Studio Max, endre
skjerminnstillingene (oppløsning eller fargepalett), og deretter
starte 3D Studio MAX på nytt.
[English...]
- 15-bit color palette support
A 15-bit color palette is no longer supported.
- Multi-display desktop support
With a multi-display desktop, all displays use the same color palette and
display resolution. The maximum display resolution you can select is
determined by the display with the highest maximum display resolution.
If a display in your multi-display desktop doesn't support a selected
display resolution, that display will automatically use a virtual display.
With a "virtual display", parts of your "display area" are off-screen. You
can move your mouse pointer to the edge of the screen to move the visible
part of your virtual display. This virtual display feature is similar to
using the Matrox zoom (PixelTOUCH) feature.
Note: The "virtual display" feature isn't available with the secondary
display of a DualHead-supporting graphics card. If a secondary display is
part of your multi-display desktop, the maximum display resolution you can
select is limited by the maximum display resolution of your secondary
display. For more information on DualHead, see "DualHead notes".
Software monitor settings help determine the maximum display resolution
for each display. If software monitor settings aren't properly selected for
all displays, one or more displays may become garbled or unusable if an
unsupported display resolution is selected. For more information on
selecting software monitor settings, see the online PowerDesk guide
(online.doc).
- Video playback with multi-display mode
In multi-display mode, digital video playback may be more limited than in
single-display mode. Specifically, some DVD or video playback programs may
not start at all or play back with lower quality. You may be able to run the
program and/or improve playback quality by closing the program, switching to
single-display mode, and then restarting the program. For more information
on switching to single-display mode, see other Matrox documentation.
This limitation may not apply to "DualHead Multi-Display" mode. For more
information, see "DualHead notes" in this file.
- OpenGL support
Note the following limitations related to the OpenGL driver included with
Matrox PowerDesk:
- OpenGL support may not be included in some versions of Matrox PowerDesk.
For a version of Matrox PowerDesk with OpenGL support enabled, see
the Matrox Web site (www.matrox.com/mga).
- Under Windows NT 4.0, OpenGL acceleration isn't supported with
Matrox MMS (Multi-Monitor Series) graphics cards or if you have more
than one Matrox graphics card installed in your computer.
- With DualHead-supporting graphics cards, OpenGL acceleration is
available while using "DualHead Multi-Display" mode under
Windows NT 4.0, (as long as there isn't another graphics card installed
in your computer).
- Using 3D Studio Max 2.0, you may experience problems with the viewports
being improperly redrawn. If this happens, simply click in a viewport
to properly update their display. (This problem isn't present with
version 2.5 or 3.0 of 3D Studio Max.)
- System memory requirements
Because of a limitation in Windows NT 4.0, you may experience problems
if your computer doesn't have more system memory than the total amount
of graphics memory used in your computer. To determine the amount of
graphics memory used in your computer, add the total amount of graphics
memory on each installed Matrox graphics card.
Depending on your total amount of graphics memory, here are some
recommended amounts of system memory for Windows NT 4.0:
Graphics memory | System memory
(total) | (recommended)
-------------------+------------------
32 MB | 64 MB or more
64 MB | 128 MB or more
128 MB | 192 MB or more
160 MB | 256 MB or more
- Full-screen DOS support with multiple graphics chip
If you have more than 10 graphics chips in your system (for example, 3
Matrox MMS-Quad cards), your system may stop responding when running a
DOS program in full-screen mode. If your DOS program supports it, run it
in a DOS window.
[...English]
Matrox TV-utdata
================
Enkelte modeller av Matrox-grafikkort støtter TV-utdata. Med støtte for
TV-utdata kan du vise eller ta opp bildet fra dataskjermen med en TV eller
videospiller koblet til grafikkortet.
Anbefalinger
------------
- Når du spiller spill med TV-utdata, anbefaler vi at du bruker en
skjermoppløsning på 640 x 480. Dette fordi de fleste TVer har lavere
oppløsning enn dataskjermer. Hvis du bruker en høyere oppløsning (800 x 600
eller 1024 x 786), blir bildet kanskje ikke like skarpt på TVen som på
dataskjermen - de minste detaljene kan være vanskeligere å se på TVen.
- (for Matrox G100/G200-kort)
Matrox' standardinnstillinger for avanserte TV-utdata er egnet til visning
av de fleste slags datagrafikk (for eksempel dataspill eller Windows-
skrivebordet) på de fleste TVer. Det finnes også avanserte
TV-utdatainnstillinger som er basert på kringkastingsstandarder og som er
bedre egnet til visning av fullskjermsvideo (for eksempel fra en videofil).
Disse innstillingene omfatter:
NTSC
Lysstyrke : 180
Kontrast : 234
Metning : 137
Nyanse : 0
PAL
Lysstyrke : 167
Kontrast : 255
Metning : 138
Nyanse : 0
Merk: Du må kanskje justere innstillingene på TVen også for å få best mulig
bilde. Standardinnstillingene for lysstyrke, kontrast, metning og nyanser
på de fleste vanlige TVer/videospillere er høyere enn
kringkastningsstandardene. Disse innstillingene er vanligvis egnet til
visning av video/TV, men vil kanskje ikke gi et bra resultat med
datagrafikk. Hvis du vil ha mer informasjon om hvordan du justerer
innstillingene på TVen, se håndboken for TVen.
Mer informasjon
---------------
Hvis du vil ha mer informasjon om skjerminnstillinger, se Matrox-håndboken og
den elektroniske dokumentasjonen. Hvis du vil ha informasjon om hvordan du
endrer skjermoppløsningen for et spill du bruker, se dokumentasjonen for
spillet.
Merk: Matrox-funksjonene for zoom og virtuelt skrivebord støttes ikke i
TV-utmodus. Det er heller ikke støtte for TV-skjerm hvis du har mer enn ett
Matrox-grafikkort i datamaskinen.
[English...]
Note: For TV output with full-screen DOS display modes under Windows NT 4.0,
only text display modes (02h, 03h) are supported.
DualHead notes
==============
Certain Matrox graphics cards can use one graphics chip to control two
separate displays -- this is the Matrox "DualHead" feature. If you have a
DualHead-supporting graphics card, note the following under Windows NT 4.0:
- DualHead software controls (on the Matrox PowerDesk "DualHead" property
sheet) are only available if, when Windows NT 4.0 restarts, a secondary
display is connected to your DualHead-supporting graphics card. For more
information on DualHead software controls, see context-sensitive help.
- The "VESA settings" option isn't available when you're using a TV as your
secondary display.
- With the "DualHead Multi-Display" feature, DirectDraw and OpenGL
acceleration is available for the main and secondary displays of your
DualHead-supporting graphics card.
- With the "DualHead Multi-Display" feature, all displays in your system
may be limited by the display capabilities of the secondary display of
your DualHead-supporting graphics card. Specifically:
- Only a 16- or 32-bit color palette is available.
- The Matrox zoom feature (PixelTOUTCH) is unavailable.
- The mouse pointer is drawn entirely by the software. As a result, the
mouse pointer may flicker or disappear while it's in an area of the
display that's being redrawn quickly (for example, a video window).
- Because the secondary display doesn't support the "virtual display"
feature, the maximum display resolution of a multi-display desktop is
limited by the maximum display resolution of the secondary display.
- If you have a DualHead supporting graphics card and you're using DualHead
Multi-Display, Clone, or Zoom mode, digital video may appear as a solid
color on your secondary display. This can happen if video is played using
the hardware-overlay feature of your Matrox graphics card. Video played
using the overlay feature is generally of higher quality but it can be
viewed only on your main display.
Because only one program at a time can use the overlay feature, any other
program started while the overlay feature is used won't be able to use the
feature. The overlay feature will be available to the first program to
start after the program currently using the overlay is closed.
For video that normally uses the hardware-overlay feature, you may be able
to view the digital video on your secondary display by running another
instance of the video player. For example, if you're viewing a file using
the overlay feature with Microsoft Media Player, double-clicking on the file
again starts another instance of the Media Player. This instance properly
plays video on your secondary display. Then, you could close the first
instance of the Media Player and still be able to view video on your
secondary display.
- The "DualHead Clone" feature is unavailable if your DualHead-supporting
graphics card isn't controlling the primary display of your computer.
The "primary display" of your computer is the one that first displays
information when your computer restarts. For information on how to change
which graphics card controls your primary display, see your system manual.
- With the "DualHead Clone" feature, both the main and secondary
display of your DualHead-supporting graphics card use the same monitor
settings (specifically, the same vertical refresh rate).
If your secondary display is a TV, the vertical refresh rate is determined
by the TV standard selected on the Matrox PowerDesk "Monitor" property
sheet (60 Hz for NTSC, 50 Hz for PAL).
If your secondary display is a computer monitor, the "Monitor" property
sheet isn't available. In this case, use the "Refresh Frequency" control
on the "Settings" property sheet to change your vertical refresh rate. If
you select a refresh rate or display resolution that isn't supported by
either display, one or both displays may become garbled or unusable.
- With the "DualHead Clone" feature, the virtual desktop feature is
unavailable.
[...English]
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.