; ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ; File: IRDASMC.INF ; ; INF to install SmcIrda.Sys NDIS 5.0 Miniport for SMC IrCC ; on Windows 2000 ; ; Copyright 1997 - 2000 Standard Microsystems Corp. ; (nw) ; ; Update for NT5, Build 1804 w/ SmcIrda.Sys V2.24, 5/29/98 (nw) ; to remove in the future, search on "1804" ; ; 4/21/99 (yo) ; IOConfig for the 3rd IO port (config reg) is added for only ; CAM35C44 EVB use on desktop PC ; ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ; [version] CatalogFile=irdasmc.cat ;LayoutFile=layout.inf ; should only use this if installing as part of OS signature="$Windows NT$" Class = Infrared ClassGUID = {6bdd1fc5-810f-11d0-BEC7-08002BE2092F} provider=%strSMC% DriverVer=09/14/2000, 4.10.1999.4 [DestinationDirs] DefaultDestDir=12 ; %windir%\system32\drivers *SMCF010.SysCopyFiles=12 *SMCF010.SysDelFiles=12 [Manufacturer] %strSMC%=SMC_IRCC [ControlFlags] ExcludeFromSelect=*SMCF010 [SMC_IRCC] %*SMCF010.DeviceDesc%=*SMCF010.ndi, *SMCF010 ;%SMCEval.DeviceDesc%=SMCEval.ndi, SMCEval ; uncomment this line to install SMC eval board. [*SMCF010.ndi] DeviceID=*SMCF010 DelReg=SMC_DelReg AddReg=*SMCF010.ndi.reg,*SMCF010.ndi.param MaxInstance=1 BusType=14 ; ISAPNP Bus Characteristics=0x4 ; NCF_PHYSICAL CopyFiles=*SMCF010.SysCopyFiles DriverVer=09/14/2000, 4.10.1999.4 [SMCF010.ndi.Coinstallers] DelReg=SMC_DelCoinstallers [SMCEval.ndi] DeviceID=SMCEval DelReg=SMC_DelReg AddReg=*SMCF010.ndi.reg,*SMCF010.ndi.param,*SMCF010.ndi.eval.reg LogConfig=*SMCF010.Lc.Default,*SMCF010.Lc.Dma8,*SMCF010.Lc.Dma16,*SMCF010.Lc.NoDma MaxInstance=1 BusType=1 ; ISA Bus Characteristics=0x4 ; NCF_PHYSICAL CopyFiles=*SMCF010.SysCopyFiles DriverVer=09/14/2000, 4.10.1999.4 [SMCEval.ndi.Coinstallers] DelReg=SMC_DelCoinstallers ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ; LOG CONFIG Sections ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ; ; The first IOConfig is for the SIR/UART portion of the IrCC. ; The second IOConfig is for the FIR/SCE portion of the IrCC. ; This order is required! ; ; For the Lc.NoDma case, the speed will be limited to 115.2 Kbps ; (i.e., SIR-only) even if higher speeds are enabled in the ; SpeedEnable key (below). ; ; These LC's are ignored if a PnP BIOS is enumerating the IrCC. ; These LC's are for ISA Evaluation Boards which have no PnP BIOS. ; ; The first time a Resource property sheet is opened after installation, ; The values from the Lc.Default section (i.e., Configuration 0) will ; be displayed. Some mouse clicks can be saved by setting these values ; to match the actual hardware values. The values here correspond to ; the default settings of SMSC's CAM35C44 EVB, board BASE=0x240, ; SIR=COM3 (0x3e8), irq5, dma1. ; ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ; NT5, Build 1804 with SMSC CAM35C44 EVB -- disable COM ENA_L switch ; on EVB so that SIR UART does *NOT* show up as a COM port. ; Set SirBase for BASE+10h instead. ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ; [*SMCF010.Lc.Default] ConfigPriority=HARDRECONFIG ; IOConfig=3e8-3ef(3ff::) IOConfig=250-257(3ff::) ; patch for build 1804 IOConfig=258-25f(3ff::) IRQConfig=5 DMAConfig=1 [*SMCF010.Lc.Dma8] ConfigPriority=HARDRECONFIG DMAConfig=0,1,2,3 IRQConfig=3,4,5,7,9,10,11,12,14,15 ; IOConfig=2e8-2ef(3ff::),2f8-2ff(3ff::),3e8-3ef(3ff::),3f8-3ff(3ff::) ; 16-bit IOConfig=8@100-fff%fff8(3ff::) ; patch for build 1804 IOConfig=8@100-fff%fff8(3ff::) IOConfig=10@100-fff%ffe0(3ff::) ; for config reg [*SMCF010.Lc.Dma16] ConfigPriority=HARDRECONFIG DMAConfig=W:5,6,7 IRQConfig=3,4,5,7,9,10,11,12,14,15 ; IOConfig=2e8-2ef(3ff::),2f8-2ff(3ff::),3e8-3ef(3ff::),3f8-3ff(3ff::) ; 16-bit IOConfig=8@100-fff%fff8(3ff::) ; patch for build 1804 IOConfig=8@100-fff%fff8(3ff::) IOConfig=10@100-fff%ffe0(3ff::) ; for config reg [*SMCF010.Lc.NoDma] ConfigPriority=HARDRECONFIG IRQConfig=3,4,5,7,9,10,11,12,14,15 ; IOConfig=2e8-2ef(3ff::),2f8-2ff(3ff::),3e8-3ef(3ff::),3f8-3ff(3ff::) ; 16-bit IOConfig=8@100-fff%fff8(3ff::) ; patch for build 1804 IOConfig=8@100-fff%fff8(3ff::) IOConfig=10@100-fff%ffe0(3ff::) ; for config reg ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ; Add Registry Section for Install ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; [*SMCF010.ndi.reg] HKR,Ndi,Service,0,"SMCIRDA" HKR,Ndi\Interfaces,DefUpper,0,"ndisirda" HKR,Ndi\Interfaces,UpperRange,0,"ndisirda" HKR,Ndi\Interfaces,DefLower,0,"nolower" HKR,Ndi\Interfaces,LowerRange,0,"nolower" HKR,Ndi,BoardType,0,"3" HKR,Ndi,RequiredAll,0,"MS_IrDA" ; ; This is the text that shows in the display area at the bottom ; of the Network dialog when this Adapter is selected in the ; scrolling window above. ; HKR,Ndi,HelpText,,%strSmcIrdaHelp% [SMC_DelReg] HKR,,EnumPropPages32 [SMC_DelCoinstallers] HKR,,CoInstallers32 [*SMCF010.ndi.eval.reg] HKR,,SmcIrdaOptions,0x00010001,1 ; all xceivers except certain HP's ; HKR,,SmcIrdaOptions,0x00010001,2 ; for HP1100/2100 xceivers ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ; Parameters Section -- part of AddReg on Install ; Key values are adjustable on ADVANCED Property Sheet ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; [*SMCF010.ndi.param] ; ; Infrared Transceiver Selection ; ; If AUTO [default], then driver will auto-detect at initialization, ; which will produce a single spurious Tx pulse if HP/Sharp. ; This key can be used to prevent this from happening, if desired. ; HKR,Ndi\params\RxSel,ParamDesc,,%strRXSEL% HKR,Ndi\params\RxSel,default,,"0" HKR,Ndi\params\RxSel,type,,enum HKR,Ndi\params\RxSel\enum,"0",,%strRXSEL_0% HKR,Ndi\params\RxSel\enum,"1",,%strRXSEL_1% HKR,Ndi\params\RxSel\enum,"2",,%strRXSEL_2% HKR,Ndi\params\RxSel\enum,"3",,%strRXSEL_3% HKR,Ndi\params\RxSel\enum,"4",,%strRXSEL_4% HKR,,RxSel,,"0" ; For some reason defaults are not being picked up. ; ; IrDA Minimum Turnaround Time (value in microseconds) ; HKR,Ndi\params\MinTurnTime,ParamDesc,,%strIRDATURNTIME% HKR,Ndi\params\MinTurnTime,default,,"1000" HKR,Ndi\params\MinTurnTime,type,,enum HKR,Ndi\params\MinTurnTime\enum,"500",,%strMinTurnTime_500% HKR,Ndi\params\MinTurnTime\enum,"1000",,%strMinTurnTime_1000% HKR,Ndi\params\MinTurnTime\enum,"5000",,%strMinTurnTime_5000% HKR,Ndi\params\MinTurnTime\enum,"10000",,%strMinTurnTime_10000% HKR,,MinTurnTime,,"1000" ; For some reason defaults are not being picked up. ; ; Maximum Speed ; HKR,Ndi\params\MaxSpeed,ParamDesc,,%strMAXSPEED% HKR,Ndi\params\MaxSpeed,flag,1,20,00,00,00 HKR,Ndi\params\MaxSpeed,default,,"8" HKR,Ndi\params\MaxSpeed,type,,enum HKR,Ndi\params\MaxSpeed\enum,"1",,%strMaxSpeed_1% HKR,Ndi\params\MaxSpeed\enum,"2",,%strMaxSpeed_2% HKR,Ndi\params\MaxSpeed\enum,"3",,%strMaxSpeed_3% HKR,Ndi\params\MaxSpeed\enum,"4",,%strMaxSpeed_4% HKR,Ndi\params\MaxSpeed\enum,"5",,%strMaxSpeed_5% HKR,Ndi\params\MaxSpeed\enum,"6",,%strMaxSpeed_6% HKR,Ndi\params\MaxSpeed\enum,"7",,%strMaxSpeed_7% HKR,Ndi\params\MaxSpeed\enum,"8",,%strMaxSpeed_8% HKR,,MaxSpeed,,"8" ; For some reason defaults are not being picked up. ; ; IrDA Speed enables ; ; bit=1 enables corresponding speed, 1FF is all speeds [default]) ; ; d0 = 2400 d4 = 57600 d8 = 4000000 ; d1 = 9600 d5 = 115200 ; d2 = 19200 d6 = 576000 ; d3 = 38400 d7 = 1152000 ; ; Note: Miniport will always enable 9600, ; no matter what this key says ; HKR,,SpeedEnable,,"1FF" ; For some reason defaults are not being picked up. ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ; Services Section ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; [*SMCF010.ndi.Services] AddService=SMCIRDA,2,SMCIRDA.AddService, common.EventLog [SMCEval.ndi.Services] AddService=SMCIRDA,2,SMCIRDA.AddService, common.EventLog [SMCIRDA.AddService] DisplayName=%*SMCF010.ServiceDesc% ServiceType=1 ; SERVICE_KERNEL_DRIVER StartType=3 ; SERVICE_DEMAND_START ErrorControl=1 ; SERVICE_ERROR_NORMAL ServiceBinary=%12%\smcirda.sys ; where the driver is LoadOrderGroup=NDIS [common.EventLog] AddReg=common.AddEventLog.reg [common.AddEventLog.reg] HKR,,EventMessageFile,0x00020000,"%%SystemRoot%%\System32\netevent.dll;%%SystemRoot%%\System32\Drivers\SmcIrda.Sys" HKR,,TypesSupported,0x00010001,7 ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ; File/Directory Sections ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; [*SMCF010.SysCopyFiles] smcirda.sys,,,2 ; Do not skip file [*SMCF010.SysDelFiles] smcirda.sys ; SourceDisksNames not required if installing as part of OS [SourceDisksNames] ;1=%strDiskName%,%fileTagFile%, 1=%strDiskName%,,, ; Specifies the location of each file referencing the ; [SourceDisksNames] section [SourceDisksFiles] smcirda.sys = 1 ; smcirda.inf = 1 irdasmc.cat=1 ; required by WHQL ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ; Localizable Strings ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; [strings] strSMC="SMC" SMCEval.DeviceDesc="SMC IrCC - Fast Infrared Port Manual Install" *SMCF010.DeviceDesc="SMC IrCC - Fast Infrared Port" *SMCF010.ServiceDesc="SMC IrCC Miniport Device Driver" strSmcIrdaHelp="The SMC IrCC Device permits wireless communication with other devices conforming to IrDA standards using invisible infrared light." strDiskName="SMC IR_NDIS" fileTagFile=SmcIrda.Tag strRXSEL="Infrared Transceiver Type" strIRDATURNTIME="Min. Turn-Around Time" strMAXSPEED="Speed Limit" strRXSEL_0="AUTO [Default]" strRXSEL_1="IBM / Infineon / Temic" strRXSEL_2="HP" strRXSEL_3="Sharp" strRXSEL_4="VISHAY Telefunken" strMinTurnTime_500=" 0.5 mS" strMinTurnTime_1000=" 1.0 mS [Default]" strMinTurnTime_5000=" 5.0 mS" strMinTurnTime_10000="10.0 mS" strMaxSpeed_1=" 9.6 kbps" strMaxSpeed_2=" 19.2 kbps" strMaxSpeed_3=" 38.4 kbps" strMaxSpeed_4=" 57.6 kbps" strMaxSpeed_5=" 115.2 kbps" strMaxSpeed_6=" 576 kbps" strMaxSpeed_7="1.152 Mbps" strMaxSpeed_8="4 Mbps" V_CLASSNAME="Infrared Adapters"Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.