;---------------------------------------- ; Modem responses are normally located in the global [Modem Responses] ; section. Most modems will return one of the responses listed in the ; global responses section. If you encounter a modem with a different ; response sequence than any of the responses already listed, add that ; new sequence to the global modem respone section. You may also put new ; modem response sequences immediately following the command section of ; a specific modem. Such responses are checked before the global ; responses. ; ; Individual modems will have separate command sections. Modems with ; identical command sequences can be aliased. E.g., if modem 2 has the ; same command sequences as modem 1, then modem 2's section might be ; as follows: ; ; [modem 2] ; alias=modem 1 ; ; Aliases to aliased sections are not allowed. In other words, in the ; example given above, if you have "modem 3" which also has an identical ; command sequence to modem 1 and modem 2, you can alias modem 3 to ; modem 1, but you cannot alias modem 3 to modem 2. ;---------------------------------------- [Responses] ;---------------------------------------- ;OK, ERROR, NO DIALTONE, NO CARRIER, etc ;---------------------------------------- OK=<lf>OK<cr><lf> OK=<cr><lf>OK<cr><lf> OK=<cr><cr><lf>OK<cr><lf> OK=<hFF><cr><lf>OK<cr><lf> LOOP=<lf>RING<cr><lf> LOOP=<cr><lf>RING<cr><lf> LOOP=<cr><lf>RRING<cr><lf> LOOP=<cr><lf>RINGING<cr><lf> LOOP=<cr><lf>DIALING<cr><lf> ERROR=<cr><lf>ERROR<cr><lf> ERROR=<cr><lf>ABORTED<cr><lf> ERROR_NO_CARRIER=<cr><lf>NO CARRIER<cr><lf> ERROR_VOICE=<cr><lf>VOICE<cr><lf> ERROR_NO_DIALTONE=<cr><lf>NO DIALTONE<cr><lf> ERROR_NO_DIALTONE=<cr><lf>NO DIAL TONE<cr><lf> ERROR_BUSY=<cr><lf>BUSY<cr><lf> ERROR_NO_ANSWER=<cr><lf>NO ANSWER<cr><lf> ERROR_NO_PROMPTTONE=<cr><lf>NO PROMPTTONE<cr><lf> ;---------------------------------------- ;CONNECT responses that do not use the APPEND macro ;---------------------------------------- CONNECT=<cr><lf>CONNECT <connectbps><cr><lf> ;---------------------------------------- [Aus.Linx Tasmanian Devil 336i(v)] <speaker_on>=M1 <speaker_off>=M0 <hwflowcontrol_off>=&K0 <hwflowcontrol_on>=&K3 <compression_off>=%C0 <compression_on>=%C3 <protocol_off>=\\N0 <protocol_on>=\\N3 <autodial_off>=ATD <autodial_on>=ATDT CALLBACKTIME=10 DEFAULTOFF=compression MAXCARRIERBPS=33600 MAXCONNECTBPS=115200 DETECT_STRING=ATI3<cr> DETECT_RESPONSE=V1.510-V34_DP COMMAND_INIT=AT&F&C1&D2V1X3 S0=0 S91=13 S7=55 S95=47 S6=4<cr> COMMAND_INIT=AT<hwflowcontrol><compression><protocol><speaker><cr> COMMAND_DIAL=<autodial><phonenumber><cr> CONNECT=<cr><lf>CONNECT <carrierbps><cr><lf> CONNECT_EC=<cr><lf>CONNECT <carrierbps>/REL<cr><lf> CONNECT_EC=<cr><lf>CONNECT <carrierbps>/LAPM<cr><lf> CONNECT_EC=<cr><lf>CONNECT <carrierbps>/LAPM-V<cr><lf> CONNECT_EC=<cr><lf>CONNECT <carrierbps>/MNP<cr><lf> CONNECT_EC=<cr><lf>CONNECT <carrierbps>/MNP5<cr><lf> COMMAND_LISTEN=ATS0=2<cr> CONNECT=<cr><lf>CONNECT <carrierbps><cr><lf> CONNECT_EC=<cr><lf>CONNECT <carrierbps>/REL<cr><lf> CONNECT_EC=<cr><lf>CONNECT <carrierbps>/LAPM<cr><lf> CONNECT_EC=<cr><lf>CONNECT <carrierbps>/LAPM-V<cr><lf> CONNECT_EC=<cr><lf>CONNECT <carrierbps>/MNP<cr><lf> CONNECT_EC=<cr><lf>CONNECT <carrierbps>/MNP5<cr><lf> ;---------------------------------------- [Aus.Linx Tasmanian Devil 336e] <speaker_off>=M0 <speaker_on>=M1 <hwflowcontrol_off>=&K0 <hwflowcontrol_on>=&K3 <compression_off>=%C0 <compression_on>=%C3 <protocol_off>=\\N0 <protocol_on>=\\N3 <autodial_off>=ATD <autodial_on>=ATDT CALLBACKTIME=10 DEFAULTOFF=compression MAXCARRIERBPS=33600 MAXCONNECTBPS=115200 DETECT_STRING=ATI3<cr> DETECT_RESPONSE=AUSLINX/TASMANIAN DEVIL336<cr>V1.510.05-V34_DS COMMAND_INIT=AT&F&C1&D2V1W1 S95=47 S0=0<cr> COMMAND_INIT=AT<hwflowcontrol><compression><protocol><speaker><cr> COMMAND_DIAL=<autodial><phonenumber><cr> CONNECT=<cr><lf>CONNECT <carrierbps><cr><lf> CONNECT_EC=<cr><lf>CONNECT <carrierbps>/REL<cr><lf> CONNECT_EC=<cr><lf>CONNECT <carrierbps>/LAPM<cr><lf> CONNECT_EC=<cr><lf>CONNECT <carrierbps>/LAPM-V<cr><lf> CONNECT_EC=<cr><lf>CONNECT <carrierbps>/MNP<cr><lf> CONNECT_EC=<cr><lf>CONNECT <carrierbps>/MNP5<cr><lf> COMMAND_LISTEN=ATS0=2<cr> CONNECT=<cr><lf>CONNECT <carrierbps><cr><lf> CONNECT_EC=<cr><lf>CONNECT <carrierbps>/REL<cr><lf> CONNECT_EC=<cr><lf>CONNECT <carrierbps>/LAPM<cr><lf> CONNECT_EC=<cr><lf>CONNECT <carrierbps>/LAPM-V<cr><lf> CONNECT_EC=<cr><lf>CONNECT <carrierbps>/MNP<cr><lf> CONNECT_EC=<cr><lf>CONNECT <carrierbps>/MNP5<cr><lf> ;---------------------------------------- [Aus.Linx Redback 336e(i)] <speaker_off>=M0 <speaker_on>=M1 <hwflowcontrol_off>=&K0 <hwflowcontrol_on>=&K3 <compression_off>=%C0 <compression_on>=%C3 <protocol_off>=\\N0 <protocol_on>=\\N3 <autodial_off>=ATD <autodial_on>=ATDT CALLBACKTIME=10 DEFAULTOFF=compression MAXCARRIERBPS=33600 MAXCONNECTBPS=115200 DETECT_STRING=ATI3<cr> DETECT_RESPONSE=V2.011.1-V34_ACF_DP1 DETECT_RESPONSE=V2.011.1-V34_ACF_DS1 COMMAND_INIT=AT&F&C1&D2V1W1 S95=47 S0=0<cr> COMMAND_INIT=AT<hwflowcontrol><compression><protocol><speaker><cr> COMMAND_DIAL=<autodial><phonenumber><cr> CONNECT=<cr><lf>CONNECT <carrierbps><cr><lf> CONNECT_EC=<cr><lf>CONNECT <carrierbps>/V42BIS<cr><lf> COMMAND_LISTEN=ATS0=2<cr> CONNECT=<cr><lf>CONNECT <carrierbps><cr><lf> CONNECT_EC=<cr><lf>CONNECT <carrierbps>/V42BIS<cr><lf> ;--------------------------------------------------------------------------Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.