CNT32W95.TXT Driver File Contents (enl-816-tb-us.exe)

*****************************************************************************
*                                                                           *
*                       ISA PnP Ethernet Adapter                            *
*                                                                           *
*               32 Bit ODI Driver for Client32 in Windows 95                *
*                                                                           *
*                         V. 3.63,   Jan. 1997                              *
*                                                                           *
*****************************************************************************

Introduction:
=============

  This document shows you how to setup the driver and how to use the enhanced
  functions by setting the custom keywords.


Contents of the Subdirectory:
=============================

    PNPNWSRV.LAN        The 32 Bit ODI driver for Client32 in Windows 95.
    PNPNWSRV.INF        The installation information file.
    CNT32W95.TXT        This file.


Installation:
=============

  Before  starting  with the installation process, make sure that the adapter
  is  properly  installed  and configured. You can use the diagnostic program
  (A:\SETUP.EXE) in DOS mode to make sure your connection with the network is
  correct.

  Install Driver While Installing Client32:
  -----------------------------------------
    When you are going to install your Client 32 software, please refer to the
    following steps to setup the driver for adapter:

    1) Execute SETUP.EXE from Disk 1 of the Client 32 for Windows 95 software.

    2) When  the  Network  window  comes  up ,  remove  the components already
       installed, if any. Select " Add adapter " -> " Have Disk..." to install
       driver from the diskette that comes with your lan adapter.

    3) Insert the driver diskette into your floppy  drive ,  and  specify  the
       path of the driver in the diskette ( i.e.  A:\NETWARE\CLIENT32.W95 ) to
       copy the driver files to your system.

    4) You  can  select  " ISA Plug & Play  Ethernet Adapter" from the Network
       Components list, and then choose"Properties". In the Properties window,
       click "Advanced" button to configure the special functions provided  by
       the adapter.Please refer to the next section,"Configuration Parameters"
       , to setup the parameters. Click "ODI Driver" botton to make sure it is
       in 32 Bit mode. And, click "Bindings" to ensure that it binds with "IPX
       32-Bit Protocol for Novell NetWare Client 32".

    5) When the Client 32 installation is completed, reboot your PC.


  Client32 Installed in System Already:
  -------------------------------------
    1. Adapter in PnP Mode:

      1) Turn the  power of your PC on to boot  from  Windows 95. Windows 95 may
         auto-detect  your  new  adapter install,  and  the "New Hardware Found"
         dialogue box will appear. Select "Driver from disk provided by hardware
         manufacturer" to install driver from the diskette  that  come with your
         lan adapter.

         Note:
         If  your  new  adapter  is  not  detected  by Windows 95 , you can open
         "My Computer" -> "Control Panel" -> "Networks"  after Windows 95  comes
         up, and select "Add adapter" -> "Have Disk..."  to install driver  from
         the diskette that comes with your lan adapter.

      2) Insert the driver diskette into your floppy drive, and specify the path
         of the driver in the diskette(i.e. A:\NETWARE\CLIENT32.W95) to copy the
         driver files to your system.

      3) You  can  select  "ISA Plug & Play Ethernet Adapter "  from the Network
         Components  list ,  and  then  choose  " Properties". In the Properties
         window, click " Advanced " button  to  configure  the special functions
         provided by the adapter.Please refer to the next section,"Configuration
         Parameters", to setup the parameters. Click "ODI Driver" botton to make
         sure it is in 32 Bit mode.And, click "Bindings" to ensure that it binds
         with "IPX 32-Bit Protocol for Novell NetWare Client 32".

      4) When the driver installation is completed, restart Windows 95.


    2. Adapter in Jumpless Mode:

      1) After Windows 95 comes up, you can open "My Computer"->"Control Panel" -> "Networks", and select "Add adapter" -> "Have Disk"
         to install driver from the diskette that comes with  your lan adapter.

      2) Insert the driver diskette into your floppy drive ,  and  specify  the
         path of the driver in the diskette ( i.e.  A:\NETWARE\CLIENT32.W95) to
         copy the driver files to your system.

      3) You will see the prompt " ISA  Plug & Play  Ethernet  Adapter " in the
         Network Components list. Select it, and then click the  " Properties "
         button.

      4) Select "Resources", the screen will come up with settings: IRQ and I/O
         address. Make sure the values match with the board settings and do not
         conflict with other devices. You can also select "Advanced" button  to
         configure the special functions provided by the adapter. Please  refer
         to  the  next  section , " Configuration Parameters " ,  to  setup the
         parameters. Click "ODI Driver" to make sure it is in 32 Bit mode . And
         , click " Bindings " to ensure that it binds with "IPX 32-Bit Protocol
         for Novell NetWare Client 32".

      5) Restart Windows 95 and the new settings will take effect.


Configuration Parameters:
=========================
    Configuration:
    --------------
      1) Open "My Computer" -> "Control Panel" -> "Networks". Select "ISA Plug
         & Play Ethernet Adapter "  from the Network Components list, and then
         click the "Properties" button.

      2) Click "Advanced" button, and you will see the following  properties :
         EarlyReceive, EarlyTransmit and FullDuplex. Turn the properties on if
         you want to enable the functions.

    Custom Properties:
    ------------------
        EARLYTRANSMIT                 This  keyword  is  used to enable turbo
                                      transmission mode for accelerating data
                                      transmission.

        EARLYRECEIVE                  This keyword is  used  to  enable turbo
                                      transmission mode for accelerating data
                                      receiption.

        FULLDUPLEX                    This  keyword  is  used  to enable full
                                      duplex mode.


Download Driver Pack

How To Update Drivers Manually

After your driver has been downloaded, follow these simple steps to install it.

  • Expand the archive file (if the download file is in zip or rar format).

  • If the expanded file has an .exe extension, double click it and follow the installation instructions.

  • Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.

  • Find the device and model you want to update in the device list.

  • Double-click on it to open the Properties dialog box.

  • From the Properties dialog box, select the Driver tab.

  • Click the Update Driver button, then follow the instructions.

Very important: You must reboot your system to ensure that any driver updates have taken effect.

For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.

server: web4, load: 1.10