*****************************************************************************
* *
* ISA PLUG & PLAY Ethernet Adapter *
* *
* NDIS2 Driver for PCNFS *
* *
*****************************************************************************
Introduction:
=============
The Ethernet NDIS2 Driver for PCNFS confirms to the Network Driver Interface
Specification ( NDIS2 ). This document shows you how to setup the driver and
how to use the enhanced functions by setting the custom keywords in
configuration file.
Files needed for installing PCNFS ( Location of driver : A:\NDIS2 )
=================================
PNPND.DOS The NDIS2 driver for PCNFS.
PROTOCOL.INI Sample protocol.ini file.
Installation:
=============
Before starting with the installation process, make sure that the adapter
is properly installed and configured. You can use the diagnostic program
( A:\SETUP.EXE ) to make sure your connection with the network is correct.
Installation procedure for PCNFS
--------------------------------
1) Run PCNFS install program and follow screen instructions.
2) When the " Configure an Ethernet network connection " appears, Select
"Ethernet" and press <Enter>.
3) Choose NE2000 network adapter and select "NDIS" and press <Enter>.
4) Follow the screen instructions to complete the installation.
5) Two subdirectory will be created after installation,default in C:\NFS
and C:\LANMAN.
6) Copy A:\NDIS2\PNPND.DOS to C:\NFS.
7) Edit CONFIG.SYS to replace the line
DEVICE=C:\LANMAN\NE2000.DOS
with
DEVICE=C:\LANMAN\PNPND.DOS
8) Edit PROTOCOL.INI file in C:\LANMAN directory,add the following section
[PNPND_NIF]
Drivername = PNPND$
INTERRUPT = 5
IOBASE = 0x300
PNPID = 0
EARLYRECEIVE = 0
EARLYTRANSMIT = 0
9) Find [NFS-NDIS] section in PROTOCOL.INI file in C:\LANMAN directory,add
the following line after "Drivername = NFSLINK$" line:
Bindings = PNPND_NIF
10) Restart the computer.
NOTE:
-----
Multiple Lan Adapters in a system:
If you want to install mutiple Lan adapter in your system, you have to
use the keyword , PNPID , in PROTOCOL.INI file to let driver locate the
right adapter. And you must set DriverName to be PNPND$ and PNPND2$ at
different section for two different adapters.You can use the diagnostic
program ( A:\SETUP.EXE ) under DOS prompt to show all the Ethernets
addresses of your adapters.
Configuration Files:
====================
Sample of configuration file:
-----------------------------
File Name: C:\CONFIG.SYS
----------
DEVICE=C:\LANMAN\PROTMAN.SYS /I:C:\LANMAN
DEVICE=C:\LANMAN\PNPND.DOS
DEVICE=C:\LANMAN\NFS-NDIS.SYS
DEVICE=C:\NFS\PCNFS.SYS
DEVICE=C:\NFS\SOCKDRV.SYS
DEVICE=C:\DOS\ANSI.SYS
File Name: C:\AUTOEXEC.BAT
----------
C:\LANMAN\NETBIND
SET NFSDRIVE=C
SET NFSPATH=C:\NFS
PRT *
CALL C:\NFS\NETWORK
CALL C:\NFS\DRIVES
LH C:\DOS\SHARE.EXE /l:500 /f:5100
RTM
File Name: C:\LANMAN\PROTOCOL.INI
----------
[protocol manager]
drivername = PROTMAN$
[PNPND_NIF]
Drivername = PNPND$
INTERRUPT = 5
IOBASE = 0x300
PNPID = 0
EARLYRECEIVE = 0
EARLYTRANSMIT = 0
[PNPND_NIF]
Drivername = PNPND2$
INTERRUPT = 9
IOBASE = 0x320
PNPID = 0
EARLYRECEIVE = 0
EARLYTRANSMIT = 0
[NFS-NDIS]
Drivername = NFSLINK$
Bindings = PNPND_NIF
Custom Keywords:
----------------
PNPID = hhhhhhhhhhhh This keyword is the Ethernet Address of
the adapter you want to drive. If there
are more than one ethernet adapters in
your system , you have to use this
keyword to let driver locate the right
adapter. However, you don't have to use
this keyword or let the value to be
zero (i.e. PNPID = 0) if there is only
one adapter in your system.
EARLYTRANSMIT This keyword is used to enable turbo
transmission mode for accelerating data
transmission.
EARLYRECEIVE This keyword is used to enable turbo
receiption mode for accelerating data
receiption.
FULLDUPLEX This keyword is used to enable full
duplex mode.
Note: For PnP mode, you don't have to define INT and PORT number.
------------------------------- End of file --------------------------------
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.