Mouse User's Manual
1994-1999 Copyright All Rights Reserved
FCC Statement on CLASS B
Note: This equipment has been tested and found to comply with the limits for
a CLASS B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
when the equipment is operated in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and if not installed
and used in accordance with the instruction manual may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. if this
equipment does cause interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
* Reorient or relocate the receiving antenna.
* Increase the separation between the equipment and receiver.
* Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
* Consult the dealer or an experienced radio TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) this device may not cause harmful interference.
(2) this device must accept any interference received, including
interference that may cause undesired operation.
1. Hardware Installation
1-1.Installing a Serial Mouse
You must have a PC fitted with a serial port(COM1/COM2) in order to
install the mouse. Plug your mouse into the serial port.
1-2.Installing a Mouse with Mouse Port (PS/2) Connector
If you have a mouse with a round mouse port connector, you must turn off
the computer before connecting or disconnecting your mouse.
1-3.Installing a Combo Mouse
The Combo Mouse comes with a PS/2 (DIN 6) cable connector, together with
a PS/2 -> Serial (COM 9) port adapter.
Before plug your mouse into the computer, try to make sure what kind of
mouse port you have. If you have a PS/2 port, plug in the original PS/2
cable connector; if you have a Serial port, please connect the adapter
first to the cable, then plug into the Serial port.
1. Turn the computer off.
2. Locate an available 6-pin round port on your computer.
3. Insert the mouse connector into the round mouse port.
4. Start your computer.
1-4.Installing a Bus Interface Board and Bus Mouse
If you have a bus mouse, you need to install the bus interface board into
your computer. Next you will need to connect the mouse to the bus port.
The Bus Interface Board Jumpers
The J1 J2 J3 J4 jumper controls interrupts in your system. Interrupt are
temporary breaks in the sequence of a program caused by various I/O
devices, such as keyboard, drawing devices, and printers. Generally, two
devices connected to the same computer cannot use the same interrupt. You
must specify a mouse interrupt that does not interfere with the other
devices connected to your computer. The jumper refer to interrupts in the
system (IRQs). If you should change the jumper. Cross out the positions
you cannot use due to the type or configuration of your system. Then
place the removable plastic hood on any position. The default setting is
IRQ5.
2. Mouse Driver Installation
2-1.Mouse Driver for DOS
(1) Insert the mouse driver diskette in Drive A (or B). Type the following:
A: <Return>
(2) On the diskette are files required for the correct installation of the
software. Type the following :
DOSINST <Return>
Follow the on-screen instructions properly.
(3) Driver Software Options
The mouse driver has several software options. To see these detailed
options on the screen by typing :
mouse / ?
(4) Uninstalling the DOS Mouse Driver
This is done by typing in the following command:
mouse /0
from the DOS prompt.
2-2.Mouse Driver for Windows 3.1
To install Mouse Driver for Windows 3.1, insert the floppy
into the drive, click on File in Program Manager, select
Run, and type
A:\SETUP31.EXE
if you insert the Mouse Driver Disk in drive A.
or type
B:\SETUP31.EXE
if you insert the Mouse Driver Disk in drive B.
Follow the instructions on the screen.
2-3.Mouse Driver for Windows NT 3.51
To install Mouse Driver for Windows NT 3.51, insert the floppy
into the drive, click on File in Program Manager, select
Run, and type
A:\SETUP.EXE
if you insert the Mouse Driver Disk in drive A.
or type
B:\SETUP.EXE
if you insert the Mouse Driver Disk in drive B.
Follow the instructions on the screen.
2-4.Mouse Driver for Windows 95, Windows 98 & Windows NT 4.0
To install Mouse Driver for Windows 95 ( or NT 4.0 ), insert the
floppy into the drive, click on the Start button, select Run,
and type
A:\SETUP.EXE
Where "A:" is the drive number you have. You may type "B:" if you use
drive B.
Follow the instructions on the screen.
2-5.Mouse Driver for PnP mouse in Windows 95 and Windows 98.
When computer system detects your PnP mouse, it will show a dialog with
"New Hardware Found" displayed. Follow the steps below to install PnP
mouse drivers.
(1) When system shows dialog "Add New Hardware Wizard", click "Next" icon.
(2) On next screen, select "Display a list of all the drivers in a
specific location, so you can select the driver you want." then click
"Next".
(3) Click "Have Disk" on next screen.
(4) Popped the dialog "Install From Disk", type "A:\Win95" or "A:\Win98"
according to your operating system environment (Windows 95 or Windows
98). Where "A:\" is the drive you have. You should type "B:\" if you
use floppy drive B. After the path typed, Click "OK".
(5) Click "Next" on next screen.
(6) Click "Next" on next screen.
(7) Follow the instructions on the following screens.
(8) Click "Finish" on last sreen then the drivers will be installed
completely.
Loading the devices drivers this way, however, does not install the user
interface programs such as the "Browser Mouse" application. Using the
"Have Disk" function will install only the mouse drivers and you will
need to set up the software tools as follow.
Insert the floppy into the drive, click on the Start button, select Run,
and type
A:\SETUP.EXE
Where "A:" is the drive number you have. You may type "B:" if you use
drive B.
Follow the instructions on the screen.
2-6.Mouse Driver for USB mouse in Windows 98.
The USB mouse drivers is used in Windows 98 only. Don't install USB mouse
driver in the operation system other than Windows 98.
The steps to install USB mouse drivers are the same as PnP mouse(see 2-4).
You should type "A:\WIN98" in "Have Disk" function only. Where "A:\" is
the drive you have. You should type "B:\" if you use floppy drive B.
2-7.Remove the Windows Mouse Driver
(1) In the Mouse Driver folder opened on installation, Click the
"Uninstall" icon, and follow the instructions on the screen.
(2) The "Uninstall" process will prompt you to change the Mouse Driver at
last step. If you do not change the Mouse Driver, the uninstallation
will not remove the Mouse Driver in order to prevent your mouse from
inactivation when you restart your computer again. But you can follow
the steps below to change the Mouse Driver latter before you restart
your computer.
(A) Windows 3.1 ( or NT 3.51 ):
a) Double click on the "Windows Setup" icon in the Main Group.
b) Select "Options".
c) Select "Change System Setting..." in Windows 3.1,
Select "Change Mouse or Keyboard..." in Windows NT 3.51.
d) Select "Mouse:\".
e) Choose the new mouse driver you require. This will override
any previous settings.
(B) If you are running Windows 95 (or NT 4.0) do the following:
a) Select "Start".
b) Select "Settings".
c) Select "Control Panel".
d) Select "Mouse" icon.
e) Select "General".
f) Select "Change".
g) Select a new mouse driver that meets your new requirements.
The new setting will over-ride the old ones.
(C) If you are running Windows 98, follow the step below
a) Select "Start"
b) Select "Settings"
c) Select "Control Panel"
d) Select "System" icon
e) Select "Device Manager"
f) Select "Mouse"
g) Select your mouse device
h) Select "Properties"
i) Select "Driver"
j) Select "Update Driver"
k) When "Update Device Driver Wizard" popping, Select "Next"
l) Select "Display a list of all the drivers in a specific
location, so you can select the driver you want"
m) Select a new mouse driver that meets your new requirements.
The new setting will over-ride the old ones.
3. Switching Mouse Mode
3-1.Switching Mouse Hareware Modes (Use mode switch)
The Serial Mouse is capable of operating either as a Microsoft Serial
Mouse or a Mouse Systems Mouse. At the base of the Mouse you will find a
slide switch. The switch has two possible positions, 'MS' and 'PC' When
the switch is set to the 'MS' position the Mouse will emulate a two-buttoned
Microsoft Mouse while setting the switch to the 'PC' position will cause
the Mouse to emulate a three-buttoned Mouse Systems Mouse.
3-2.Switching Mouse Hardware Modes (None mode switch)
As mentioned earlier, the serial mouse is capable of operating either as
a Microsoft Serial Mouse or a Mouse Systems Mouse. Which of the two modes
the mouse will operate in is determined on the power-on initialization.
If any one of the three buttons is depressed during power-on initializa-
tion, the mouse will emulate Mouse Systems Mouse. While none of the
buttons is depressed during power-on initiation the mouse will emulate
Microsoft Mouse.
3-3.Microsoft Mode
When the mouse is in Microsoft mode, only the left and right buttons are
active, while the middle button is ignored. In this mode, your mouse will
correctly emulate a Microsoft Serial Mouse.
3-4.Mouse Systems Mode
If you are a user of AUTOCAD or any other software which gives enhanced
performance with a Mouse Systems Mouse you should choose this emulation.
A Mouse Systems Mouse operates with all three buttons.
Note: Because Windows 95 and Windows NT supports serial 'MS' mouse mode, you
had better switch the mouse to 'MS' mode when first install the mouse
driver in package. After completing the installation, you can switch
to 'PC' mouse mode when restart the computer.
4. Trouble Shooting
Symptom 1 : No mouse movement.
Solution : - Make sure the software that you are using supports a mouse.
- Check that mouse is plugged into serial port at the back of
computer.
- Ensure that mouse driver is installed into system.
Symptom 2 : The cursor on the screen remains at one spot or moves erratically.
Solution : Check the mouse cable for any breaks or sharp twists. Examine the
cable closely where it connects to the mouse.
Symptom 3 : The cursor movement stops at a corner and no longer responds to
the mouse movement.
Solution : Run the mouse driver to check which mode the mouse is operating in.
Symptom 4 : Mouse movement does not produce corresponding cursor movement or
there is a brief pause during movement.
Solution : Clean the silicon rubber-coated ball and rollers.
Symptom 5 : After had selected mouse type for Windows 95 ,the mouse would be
disable when you clicked "OK" .
Solution : Using keyboard to close the current window and wait for Windows 95
to give any instruction to restart your computer.
After restart Windows 95 the mouse will work normally.
Symptom 6 : Displayed error number -115 on screen when install mouse driver
software.
Solution : The error usually occurs because a virus-checking program is being
used on the System to prevent files from being renamed. Please
shutdown any virus checking software running on the system and
then run the setup again.
Symptom 7 : Detection Problems with PS/2 Pointing Devices
Solution : If your mouse is connected to the mouse port and is not detected
by the system, attempt the following step(s):
1) Your mouse port might need to be enabled through the SETUP menu
of your computer. Please check your computer documentation
regarding the SETUP menu.
2) If you have a mouse with both serial and mouse port adaptors,
connect the mouse to the computer through the serial port.
Reboot and check if the mouse is detected properly.
3) If adaptor(s) were not included in your package, your mouse
was designed to work on only one type of port (Serial OR PS/2).
Refer to your package for the type of port your mouse supports.
If the problem persists, please check for a possible computer
BIOS ROM upgrade from your computer manufacturer.
Some notebook systems, such as IBM Thinkpad, have both an external
Mouse Port and an integrated Pointing Stick, which is connected to
the Mouse Port. If your mouse is having difficulty running on the
Mouse Port of this type of system, try using the serial port
instead.
Symptom 8 : Conflicts with other Serial Devices
Solution : Some softwares provided by other manufacturers with mouse
functions, such as Logitech MouseWare, which may conflict with
this mouse. Recommended strongly to remove the software installed
previously before install this mouse software.
Symptom 9 : Problems Operating the Wheel
Solution : If your mouse is equipped with a wheel and the wheel does not
scroll, verify the following:
1) Verify that the "Browser Mouse" or "Mouse Control Panel"
application is installed properly. If you do not find the
"Browser Mouse" or "Mouse Control Panel" icon in the system
tray, you need to reinstall mouse software.
2) Some other applications with mouse scrolling function may
conflict with this mouse function. Remove these applications
before install this mouse software.
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.