NW312.TXT Driver File Contents (fl_40hw2.zip)

                10/100M Fast Ethernet PCMCIA Adapter Installation
                         for NetWare Server 3.12 Driver


 Contents
 ÍÍÍÍÍÍÍÍ
    Introduction
    Getting Started


 Introduction
 ÍÍÍÍÍÍÍÍÍÍÍÍ
        This installation assumes that the PC Card drivers are working
        properly. Please consult INST_DOS.TXT for help with PC Card
        Drivers. Getting Started will describe the installation
        instructions.


 Getting Started
 ÍÍÍÍÍÍÍÍÍÍÍÍÍÍ

  ******************************************************************
  * Notes:                                                         *
  *     The PC Card should be enabled by Card Enabler.             *
  *     Please run ENFP16.EXE before starting LAN driver.          *
  *                                                                *
  *     Two alternatives to enable the                             *
  *     10/100M Fast Ethernet PCMCIA Adapter:                      *
  *                                                                *
  *     1. Issue an executive file:                                *
  *                                                                *
  *        At the DOS prompt, type:                                *
  *                                                                *
  *            ENFP16 [/iop:XXX] [/irq:X]                          *
  *                                                                *
  *        For more details, refer to INST_DOS.TXT.                *
  *                                                                *
  *     2. Modify CONFIG.SYS                                       *
  *                                                                *
  *        Add the following instruction to CONFIG.SYS file        *
  *                                                                *
  *        DEVICE=<PATH>\ENFP16.EXE [/iop:XXX] [/irq:X]            *
  *                                                                *
  *        ; <PATH> is a directory containing ENFP16.EXE           *
  *        ; Please refer to the INST_DOS.TXT file for details.    *
  ******************************************************************



    Modifying an existing NetWare 3.12 Server
    ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
         Make a sub-directory NLMS.OLD under <SRVPATH> directory which
          include SERVER.EXE.

          Ex. <SRVPATH> = SRV312.
              >MD \SRV312\NLMS.OLD

         Save NBI.NLM, MSM.NLM and ETHERTSM.NLM to NLMS.OLD
          sub-directory.

         Please insert driver diskette into floppy disk drive.

         Copy all provided NLM and LAN files into your dos directory
          which include SERVER.EXE, and rename NBI31X.NLM and MSM31X.NLM
          :

          Ex. >COPY A:\NETWARE\SERVER\NW312\NBI31X.NLM C:\SRV312\NBI.NLM
              >COPY A:\NETWARE\SERVER\NW312\MSM31X.NLM C:\SRV312\MSM.NLM
              >COPY A:\NETWARE\SERVER\NW312\ETHERTSM.NLM C:\SRV312
              >COPY A:\NETWARE\SERVER\NW312\FP16.LAN C:\SRV312

         Start the NetWare Server.

          > CD \SRV312
          > SERVER

         From the Novell Server side, execute "LOAD INSTALL".  Type:

              LOAD INSTALL

          Select <System Options>
          Select <Edit AUTOEXEC.NCF File>

         Add the following commands into the server's AUTOEXEC.NCF file.

          Search Add C:\SRV312

          LOAD NBI.NLM
          LOAD MSM.NLM
          LOAD ETHERTSM.NLM

          LOAD FP16 PORT=300 INT=3 FRAME=Ethernet_802.3 NAME=FP16_1_E83
          BIND IPX FP16_1_E83 NET=1111

          LOAD FP16 PORT=300 INT=3 FRAME=Ethernet_802.2 NAME=FP16_1_E82
          BIND IPX FP16_1_E82 NET=1113

          LOAD FP16 PORT=300 INT=3 FRAME=Ethernet_II NAME=FP16_1_EII
          BIND IPX FP16_1_EII NET=1115

          LOAD FP16 PORT=300 INT=3 FRAME=Ethernet_SNAP NAME=FP16_1_ESP
          BIND IPX FP16_1_ESP NET=1117

          Note: the PORT and INT parameters should be set as the values
                which are set by ENFP16.EXE.

         Restart the server again.


Download Driver Pack

How To Update Drivers Manually

After your driver has been downloaded, follow these simple steps to install it.

  • Expand the archive file (if the download file is in zip or rar format).

  • If the expanded file has an .exe extension, double click it and follow the installation instructions.

  • Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.

  • Find the device and model you want to update in the device list.

  • Double-click on it to open the Properties dialog box.

  • From the Properties dialog box, select the Driver tab.

  • Click the Update Driver button, then follow the instructions.

Very important: You must reboot your system to ensure that any driver updates have taken effect.

For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.

server: web2, load: 1.06