OEMSETUP.INF Driver File Contents (nslan.zip)

    !G:DebugOutputControl = 1 
[Identification]
    OptionType = NetAdapter

[PlatformsSupported]
    ISA
    EISA
    "Jazz-Internal Bus"
    PCI

[Options]
    dp83815   

[FileConstants]
    UtilityInf                  = "UTILITY.INF"
    subroutineinf               = "SUBROUTN.INF"
    SoftwareType                = "driver"
    Exit_Code                   = 0
    NetEventDLL                 = "%SystemRoot%\System32\netevent.dll;%SystemRoot%\System32\drivers\dp83815.sys"
    IoLogMsgDLL                 = "%SystemRoot%\System32\IoLogMsg.dll"

    Manufacturer                = "NSC"
    ProductMajorVersion         = "1"
    ProductMinorVersion         = "1"
    ProductVersion              = $(ProductMajorVersion)"."$(ProductMinorVersion)
    ProductSoftwareName         = "dp83815"
    ProductSoftwareImagePath    = "%SystemRoot%\System32\drivers\dp83815.sys"
    NetRuleSoftwareType         = "dp83815Sys ndisDriver dp83815Driver"
    NetRuleSoftwareUse          = $(SoftwareType)
    NetRuleSoftwareBindForm     = """dp83815Sys"" yes no container"
    NetRuleSoftwareClass        = {"dp83815Driver basic"}
    NetRuleSoftwareBindable     = {"dp83815Driver dp83815Adapter non exclusive 100"}
    ProductHardwareName         = "dp83815"
    NetRuleHardwareBindForm     = " yes yes container"

    ProductKeyName              = $(!NTN_SoftwareBase)"\"$(Manufacturer)"\"$(ProductSoftwareName)"\CurrentVersion"
    ParamKeyName                = $(!NTN_ServiceBase)"\"$(ProductHardwareName)"\Parameters"

    FunctionTitle               = "NSC DP83815 Bus Master Adapter Card Setup"
    ProductSoftwareDescription  = "NSC DP83815 Bus Master Adapter Driver"
    ProductSoftwareTitle        = "NSC DP83815 Bus Master Adapter Driver"

    ProductHardwaredp83815Title   = "NSC DP83815 Adapter"
    ProductHardwaredp83815Description = "NSC DP83815 Adapter "
    NetRuleHardwaredp83815Type    = "dp83815 dp83815Adapter"
    NetRuleHardwaredp83815Class   = {"dp83815Adapter basic"}

    Adapterdp83815Type            = 5             ;; PCI board
    Adapterdp83815Type            = 5             ;; PCI board
    dp83815CFID                   = 32          

[GeneralConstants]
    from      = ""
    to    = ""
    ExitCodeOk     = 0
    ExitCodeCancel = 1                
    ExitCodeFatal  = 2
    KeyNull     = ""
    MAXIMUM_ALLOWED   = 33554432
    RegistryErrorIndex = NO_ERROR
    KeyProduct  = ""
    KeyParameters   = ""
    TRUE        = 1
    FALSE       = 0
    NoTitle        = 0
    ExitState   = "Active"
    OldVersionExisted = $(FALSE)
    DriverPath  = $(!STF_NTPATH)\drivers
    NT350VersionConstant = "3.50"
    NT310VersionConstant = "3.10"

[date]
    Now = {} ? $(!LIBHANDLE) GetSystemDate

[Identify]
    read-syms Identification
    set Status     = STATUS_SUCCESSFUL
    set Identifier = $(OptionType)
    set Media      = #("Source Media Descriptions", 1, 1)
    Return $(Status) $(Identifier) $(Media)

[ReturnOptions]
    set Status        = STATUS_FAILED
    set OptionList     = {}
    set OptionTextList = {}
    set LanguageList = ^(LanguagesSupported, 1)
    Ifcontains(i) $($0) in $(LanguageList)
    ifstr(i) $($1) == ""
        goto returnoptions
    endif
        set PlatformList = ^(PlatformsSupported, 1)
    Ifcontains(i) $($1) in $(PlatformList)
        goto returnoptions
    else
        set Status = STATUS_NOTSUPPORTED
        goto finish_ReturnOptions
    endif
    else
        set Status = STATUS_NOLANGUAGE
        goto finish_ReturnOptions
    endif

returnoptions = +
    set OptionList     = ^(Options, 1)
    set OptionTextList = ^(OptionsText$($0), 1)
    set Status         = STATUS_SUCCESSFUL

finish_ReturnOptions = +
    Return $(Status) $(OptionList) $(OptionTextList)

[InstallOption]
    ;; 
    ;; Uncomment the following line for debug support under the debugger.
    ;; Set !G:DebugOutputControl=1
    ;;
    set Option   = $($1)
    set SrcDir   = $($2)
    set AddCopy  = $($3)
    set DoCopy   = $($4)
    set DoConfig = $($5)
    set FileName = ""
    set LanguageList = ^(LanguagesSupported, 1)
    Ifcontains(i) $($0) NOT-IN $(LanguageList)
    Return STATUS_NOLANGUAGE
    endif
    set-subst LF = "\n"
    read-syms GeneralConstants
    read-syms FileConstants
;   set NetRuleSoftwareBindable = $($R1)
    read-syms DialogConstants$(!STF_LANGUAGE)
    ifstr(i) $(!NTN_Origination) == "NCPA"
    set Continue = "OK"
    endif
    read-syms FileConstants$(!STF_LANGUAGE)
    detect date
    set-title  $(Function$(Option)Title)
    set to   = Begin
    set from = Begin
    set CommonStatus = STATUS_SUCCESSFUL
    EndWait

Begin = +
    ;;
    ;; If we are PCI and we are v3.51 and above, we can use the 
    ;; PCI dection routines to figure out where all the boards 
    ;; are (hopefully including different buses) and generate the correct 
    ;; reg. entries.
    ;;
    set CurrentVersionValue = ""
    OpenRegKey $(!REG_H_LOCAL) "" "SOFTWARE\Microsoft\Windows Nt\CurrentVersion" $(!REG_KEY_READ) KeyNt
    Ifstr(i) $(KeyNt) != ""
    GetRegValue $(KeyNt) "CurrentVersion" CurrentVersionValue
    Debug-Output "$(InfFile) $(Option): WinNT CurrentVersion ="$(CurrentVersionValue)
    CloseRegKey $(KeyNt)
    Endif
    
    ifstr(i) (*($(CurrentVersionValue),4)) == $(NT310VersionConstant)    
        Debug-Output "$(InfFile) $(Option): Configureadapter"
    set Error = "Windows NT v3.10 is not support by this product"
    goto fatal
    endif
    
    set TargetVersion = *($(CurrentVersionValue),4)
    Debug-Output "$(InfFile) $(Option): Current Version:"$(TargetVersion)

    ifcontains(i) $(TargetVersion) in {"3.50", "3.51"}
        set FileName   = "dp83815"
        set NDIS40     = $(FALSE)
    else
        set FileName   = "dp83815nt"
        set NDIS40     = $(TRUE)
    endif


    Ifstr(i) $(!NTN_InstallMode) == deinstall
        set StartLabel = removeadapter
    else-Ifstr(i) $(!NTN_InstallMode) == Update
        set StartLabel = UpgradeSoftware
    else-Ifstr(i) $(!NTN_InstallMode) == bind
        set StartLabel = bindingadapter
    else-Ifstr(i) $(!NTN_InstallMode) == configure
        Ifstr(i) $(ProductKeyName) == $(!NTN_RegBase)
            Shell $(UtilityInf),RegistryErrorString,CANNOT_CONFIGURE_SOFTWARE
            ifint $($ShellCode) != $(!SHELL_CODE_OK)
            goto ShellCodeError
            endif
            set Error = $($R0)
            set from = end
            set to = end
            goto nonfatalinfo
        else
            set StartLabel = configureadapter
        endif
    else
        set StartLabel = installadapter
        set OEM_ABANDON_OPTIONS = {}
        set OEM_ABANDON_SOFTWARE = FALSE
        set OEM_ABANDON_ON = TRUE
    endif

    set from = $(fatal)
    set to = $(fatal)
    goto $(StartLabel)

installadapter = +
    
    Debug-Output "$(InfFile) $(Option): Installadapter"
    OpenRegKey $(!REG_H_LOCAL) "" $(ProductKeyName) $(MAXIMUM_ALLOWED) KeyProduct
    Ifstr $(KeyProduct) != $(KeyNull)
        CloseRegKey $(KeyProduct)
        ifstr(i) !(NTN_RegBase) == $(ProductKeyName)
;           Shell $(UtilityInf), VerExistedDlg, $(ProductSoftwareTitle),+
;              $(ProductVersion)
            ifint $($ShellCode) != $(!SHELL_CODE_OK)
                Debug-Output "ShellCode error: cannot get an error string."
                goto ShellCodeError
            endif
            goto end
        else
;           Shell $(UtilityInf), CardExistedDlg
;           ifint $($ShellCode) != $(!SHELL_CODE_OK)
;               Debug-Output "ShellCode error: cannot get an error string."
;               goto ShellCodeError
;           endif
;           ifstr(i) $($R1) != "OK"
;               set CommonStatus = STATUS_USERCANCEL
;               goto end
;           endif
            set OldVersionExisted = $(TRUE)
        endif
    Endif
   Shell $(UtilityInf), DoAskSource, $(!STF_CWDDIR), $(SrcDir) NO
   Ifint $($ShellCode) != $(!SHELL_CODE_OK)
       Goto ShellCodeError
   Else-Ifstr(i) $($R0) == STATUS_FAILED
       Shell $(UtilityInf) RegistryErrorString "ASK_SOURCE_FAIL"
       ifint $($ShellCode) != $(!SHELL_CODE_OK)
           goto ShellCodeError
       endif
       set Error = $($R0)
       Goto fatal
   Else-Ifstr(i) $($R0) == STATUS_USERCANCEL
      Goto successful
   Endif
   Set SrcDir = $($R1)\

  Debug-Output "Source Dir"$(SrcDir)

    Goto adapteroptions    

configureadapter = +
    Debug-Output "$(InfFile) $(Option): Configureadapter"

    set Error = "Cannot configure the software component"
    goto fatal

adapteroptions = +
    Debug-Output "$(InfFile) $(Option): Adapteroptions"
    set from = adapteroptions
    ifstr(i) $(!NTN_InstallMode) == configure
       goto updateparameters
    endif

installproduct =+
    Debug-Output "$(InfFile) $(Option): installproduct"
    StartWait 
    set AdapterList = $($R1)
    ifint $(OldVersionExisted) == $(FALSE)
        Ifstr(i) $(DoCopy) == "YES"
            Shell $(UtilityInf), DoAskSource, $(!STF_CWDDIR), $(SrcDir) NO
            ifint $($ShellCode) != $(!SHELL_CODE_OK)
                Goto ShellCodeError
            Else-Ifstr(i) $($R0) == STATUS_FAILED
                Shell $(UtilityInf) RegistryErrorString "ASK_SOURCE_FAIL"
                ifint $($ShellCode) != $(!SHELL_CODE_OK)
                    goto ShellCodeError
                endif
                set Error = $($R0)
                Goto fatal
            Else-Ifstr(i) $($R0) == STATUS_USERCANCEL
                Goto successful
            Endif
            Set SrcDir = $($R1)\
        Endif

        install "Install-Option"
        ifstr(i) $(STF_INSTALL_OUTCOME) != STF_SUCCESS
            Shell $(UtilityInf) RegistryErrorString "UNABLE_COPY_FILE"
            ifint $($ShellCode) != $(!SHELL_CODE_OK)
                goto ShellCodeError
            endif
            set Error = $($R0)
            goto fatal
        endif
    endif

    ;;
    ;; Check to see if the Product Software key exists already in 
    ;; the system service keys before we try to add the software 
    ;; component.
    ;; 
    OpenRegKey $(!REG_H_LOCAL) "" $(!NTN_ServiceBase)"\"$(ProductHardwareName) $(!REG_KEY_READ) KeyNt
    CloseRegKey $(KeyNt)

    Ifstr(i) $(KeyNt) == ""
        Shell $(UtilityInf), AddSoftwareComponent, $(Manufacturer), +
        $(ProductSoftwareName), +
        $(ProductSoftwareName), +
        $(ProductSoftwareTitle), $(STF_CONTEXTINFNAME), +
        $(ProductSoftwareImagePath), "kernel", "NDIS", {}, "",+
        $(NetEventDLL)
        
        Set OEM_ABANDON_SOFTWARE = TRUE
        ifint $($ShellCode) != $(!SHELL_CODE_OK)
            goto ShellCodeError
        endif
        set RegistryErrorIndex = $($R0)
        Ifstr(i) $(RegistryErrorIndex) != "NO_ERROR"
            EndWait
            CloseRegKey $($R1)
            CloseRegKey $($R2)
            CloseRegKey $($R3)
            CloseRegKey $($R4)
            CloseRegKey $($R5)
            goto fatalregistry
        endif
        Set SoftProductKey      = $($R1)
        Set SoftNetRuleKey      = $($R2)
        Set SoftServiceKey      = $($R3)
        Set SoftParameterKey    = $($R4)
        Set SoftLinkageKey      = $($R5)
        set NewValueList = {{SoftwareType,$(NoTitle),$(!REG_VT_SZ),$(SoftwareType)},+
               {MajorVersion,$(NoTitle),$(!REG_VT_DWORD),$(ProductMajorVersion)},+
               {MinorVersion,$(NoTitle),$(!REG_VT_DWORD),$(ProductMinorVersion)},+
               {Title,$(NoTitle),$(!REG_VT_SZ),$(ProductSoftwareTitle)},+
               {Description,$(NoTitle),$(!REG_VT_SZ),$(ProductSoftwareDescription)},+
               {ServiceName,$(NoTitle),$(!REG_VT_SZ),$(ProductSoftwareName)},+
               {InstallDate,$(NoTitle),$(!REG_VT_DWORD),*($(Now),1)}}
        Shell  $(UtilityInf), AddValueList, $(SoftProductKey), $(NewValueList)
        ifint $($ShellCode) != $(!SHELL_CODE_OK)
            goto ShellCodeError
        endif
        set RegistryErrorIndex = $($R0)
        Ifstr(i) $(RegistryErrorIndex) != "NO_ERROR"
            EndWait
            CloseRegKey $(SoftProductKey)
            CloseRegKey $(SoftNetRuleKey)
            CloseRegKey $(SoftServiceKey)
            CloseRegKey $(SoftParameterKey)
            CloseRegKey $(SoftLinkageKey)
            goto fatalregistry
        endif
        set NewValueList = {{type,$(NoTitle),$(!REG_VT_SZ),$(NetRuleSoftwareType)},+
                {use,$(NoTitle),$(!REG_VT_SZ),$(NetRuleSoftwareUse)}, +
                {bindform,$(NoTitle),$(!REG_VT_SZ),$(NetRuleSoftwareBindForm)}, +
                {class,$(NoTitle),$(!REG_VT_MULTI_SZ),$(NetRuleSoftwareClass)}, +
                {bindable,$(NoTitle),$(!REG_VT_MULTI_SZ),$(NetRuleSoftwareBindable)}, +
                {InfOption,$(NoTitle),$(!REG_VT_SZ),$(Option)}}
        Shell  $(UtilityInf), AddValueList, $(SoftNetRuleKey), $(NewValueList)
        ifint $($ShellCode) != $(!SHELL_CODE_OK)
            goto ShellCodeError
        endif
        set RegistryErrorIndex = $($R0)
        CloseRegKey $(SoftProductKey)
        CloseRegKey $(SoftNetRuleKey)
        CloseRegKey $(SoftServiceKey)
        CloseRegKey $(SoftParameterKey)
        CloseRegKey $(SoftLinkageKey)
        Ifstr(i) $(RegistryErrorIndex) != "NO_ERROR"
            EndWait
            goto fatalregistry
        endif
    endif ;; Does Services\dp83815 exist?
    
    ;;
    ;; We are PCI and if we are NT v3.51 and above, we can use the 
    ;;PCI dection routines to figure
    ;; out where all the boards are (hopefully including different buses)
    ;; and generate the correct 
    ;; reg. entries.
    ;;
    set NTDetected = $(FALSE)
        Debug-Output "$(InfFile) $(Option): About to look for NSC PCI Cards"
        ;;
        ;; Note: If we are are on WinNT v3.51 and above, we have PCI 
        ;; detection support and are able to setup the adapter without 
        ;; user intervention. Otherwise, we can only do one card at a time.
        ;;
        set TargetVersion = *($(CurrentVersionValue),4)
        Debug-Output "$(InfFile) $(Option): Current Version:"$(TargetVersion)

        ifstr $(TargetVersion) == $(NT350VersionConstant)   ;; We need to ask on v3.50
            Debug-Output "Running on WindowsNT 3.50"
            set Version350 = $(TRUE)
        else
            Debug-Output "Running on WindowsNT 3.51"
            set Version350 = $(FALSE)
        endif

        ifint $(Version350) == $(TRUE)
            Debug-Output "Running on WindowsNT v3.50, Not using PCI Detection!!!"
            ifstr $(!STF_GUI_UNATTENDED) == "YES"
                Debug-Output "$(InfFile) $(Option): Running in GUI unattended mode"
                ifstr(i) $(!AutoNetInterfaceType) != ""
                    set BusInterfaceType = $(!AutoNetInterfaceType)
                else
                    set BusInterfaceType = 5
                endif
                ifstr(i) $(!AutoNetBusNumber) != ""
                    set BusNumber = $(!AutoNetBusNumber)
                else
                    set BusNumber = 0
                endif
                set NTDetected = $(FALSE)
                set AdapterList = $(Option)   ;; 1 Item to install
                Debug-Output "$(InfFile) $(Option): BusInterfaceType = $(BusInterfaceType)"
                Debug-Output "$(InfFile) $(Option): BusNumber = $(BusNumber)"
            else        
                Debug-Output "$(InfFile) $(Option): Running 3.50 Bus Dialog"
                set BusInterfaceType = 5
                set BusNumber = 0
                set NTDetected = $(FALSE)
                Shell $(UtilityInf),GetBusTypeDialog,$(ProductHardware$(Option)Description) $(BusInterfaceType) $(BusNumber)
                ifint $($ShellCode) != $(!SHELL_CODE_OK)
                    Debug-Output "ShellCode error."
                    goto ShellCodeError
                endif
                set BusInterfaceType = $($R1)
                set BusNumber = $($R2)
                set AdapterList = $(Option)   ;; 1 Item to install
                Debug-Output "$(InfFile) $(Option): BusInterfaceType = $(BusInterfaceType)"
                Debug-Output "$(InfFile) $(Option): BusNumber = $(BusNumber)"
            endif    
        else
            Debug-Output "$(InfFile) $(Option): Running 3.51 using PCI Dectection"
            ;;
            ;; v3.51 has PCI detection code built in.
            ;;
            set NTDetected = $(TRUE)
            set Vendor = 4107      
            set-div CFID = $($(Option)CFID) 1
            Debug-Output "$(InfFile) $(Option): VendorID = $(Vendor)"
            Debug-Output "$(InfFile) $(Option): CFID = $(CFID)"
            Shell $(UtilityInf), GetPCIInformation, $(Vendor) $(CFID)
            ifint $($ShellCode) != $(!SHELL_CODE_OK)
                goto ShellCodeError
            endif
            ifstr(i) $($R0) == {}
                set Error = $(CANNOT_FIND_ANY_CARD)
                set CommonStatus = USER_CANCEL
                set from = end
                goto nonfatal
            endif
            set AdapterList = $($R0)
        endif   ;;; NT v3.50

    ;;
    ;; "AdapterList" has the list of currently installed adatpers 
    ;; in the system!
    Debug-Output "$(InfFile) $(Option): Adapterlist = $(AdatperList)"
    ForListDo $(AdapterList)
        Set InstallCard = "YES"
        ifint $(NTDetected) == $(TRUE)
            set DetectedBusNum = *($($),1)
            set DetectedSlotNum = *($($),2)
            Debug-Output "$(InfFile) $(Option): DetectedBusNumber = $(DetectedBusNum)"
            Debug-Output "$(InfFile) $(Option): DetectedSlotNum = $(DetectedSlotNum)"

            Shell $(UtilityInf), IsNetCardAlreadyInstalled, $(DetectedBusNum), +
            $(DetectedSlotNum), $(ProductHardware$(Option)Description), $(ProductHardwareName)
            
            ifint $($ShellCode) != $(!SHELL_CODE_OK)
                goto ShellCodeError
            endif
            ifstr $($R0) != "NO_ERROR"
                set Error = $($R0)
                goto fatal
            endif
            ifstr(i) $($R1) == "YES"
                set InstallCard = "NO"  ;; Don't want to re-install, it's there already
            endif    
        endif
        ;;
        ;; Are we installing the card?
        ;;
        ifstr(i) $(InstallCard) == "NO"
            Debug-Output "$(InfFile) $(Option): Card Already at $(DetectedBusNum):$(DetectedSlotNum) already installed!"
            set Error = "An adapter at $(DetectedBusNum):$(DetectedSlotNum) is already installed!"
            Shell $(subroutineinf) SetupMessage, $(!STF_LANGUAGE), $(Severity), $(Error)
            ifint $($ShellCode) != $(!SHELL_CODE_OK)
                goto ShellCodeError
            endif
        else
            Debug-Output "$(InfFile) $(Option): Installing Card at $(DetectedBusNum):$(DetectedSlotNum)!"
            Shell $(UtilityInf), AddHardwareComponent, $(ProductHardwareName),$(STF_CONTEXTINFNAME),$(ProductKeyName)
            ifint $($R4) != -1
                Set OEM_ABANDON_OPTIONS = >($(OEM_ABANDON_OPTIONS), $(!NTN_SoftwareBase)"\Microsoft\Windows NT\CurrentVersion\NetworkCards\"$($R4))
            endif
            ifint $($ShellCode) != $(!SHELL_CODE_OK)
                goto ShellCodeError
            endif
            set RegistryErrorIndex = $($R0)
            Ifstr(i) $(RegistryErrorIndex) != "NO_ERROR"
                EndWait
                CloseRegKey $($R1)
                CloseRegKey $($R2)
                CloseRegKey $($R3)
                goto fatalregistry
            endif
            Set HardNetCardKey      = $($R1)
            Set HardNetRuleKey      = $($R2)
            Set HardParameterKey    = $($R3)
            set AdapterNumber = $($R4)
            set NewValueList = {{Manufacturer,$(NoTitle),$(!REG_VT_SZ),$(Manufacturer)},+
                    {Title,$(NoTitle),$(!REG_VT_SZ),"["$($R4)"] "$(ProductHardware$(Option)Title)},+
                    {Description,$(NoTitle),$(!REG_VT_SZ),$(ProductHardware$(Option)Description)},+
                    {ProductName,$(NoTitle),$(!REG_VT_SZ),$(ProductHardwareName)},+
                    {ServiceName,$(NoTitle),$(!REG_VT_SZ),$($R5)},+
                    {InstallDate,$(NoTitle),$(!REG_VT_DWORD),*($(Now),1)}}
            Shell  $(UtilityInf), AddValueList, $(HardNetCardKey), $(NewValueList)
            ifint $($ShellCode) != $(!SHELL_CODE_OK)
                goto ShellCodeError
            endif
            ;
            ;
            ; PCI 
            ;
            set BusTypeNum = 5   
            set BusMaster = "YES"
            set Bus = "PCI"      
            set CardType = 0
            ;;
            ;; If we used the OS to dected the card, then we already know bus and slot information.
            ;;        
            ifint $(NTDetected) == $(TRUE)
                set BusNumber = $(DetectedBusNum)
                set SlotNum = $(DetectedSlotNum)    
                set BusInterfaceType = $(BusTypeNum)
                ;
                ; Note: we need to record SlotNumber too so that we can 
                ; use the "IsNetCardAlreadyInstalled" routine
                ;
                Set NewValueList =  {+
                    {BusNumber,$(NoTitle),$(!REG_VT_DWORD),$(BusNumber)},+
                    {Slot,$(NoTitle),$(!REG_VT_DWORD),$(SlotNum)}+
                    }
                Debug-Output "$(InfFile) $(Option): Set HardwareParameterKey = $(NewValueList)"
                Shell  $(UtilityInf), AddValueList, $(HardParameterKey), $(NewValueList)
                ifint $($ShellCode) != $(!SHELL_CODE_OK)
                    goto ShellCodeError
                endif

                Set NewValueList = { {SlotNumber,$(NoTitle),$(!REG_VT_DWORD),$(SlotNum)} }
                Debug-Output "$(InfFile) $(Option): Set HardwareParameterKey = $(NewValueList)"
                Shell  $(UtilityInf), AddValueList, $(HardParameterKey), $(NewValueList)
                ifint $($ShellCode) != $(!SHELL_CODE_OK)
                    goto ShellCodeError
                endif
            else
                Set NewValueList =  {+
                    {BusNumber,$(NoTitle),$(!REG_VT_DWORD),$(BusNumber)},+
                    }
                Debug-Output "$(InfFile) $(Option): Set HardwareParameterKey = $(NewValueList)"
                Shell  $(UtilityInf), AddValueList, $(HardParameterKey), $(NewValueList)
                ifint $($ShellCode) != $(!SHELL_CODE_OK)
                    goto ShellCodeError
                endif
            endif

            Set NewValueList =  {+
                {BusType,$(NoTitle),$(!REG_VT_DWORD),$(BusInterfaceType)},+
                {CardType,$(NoTitle),$(!REG_VT_DWORD),$(CardType)},+
                {MediaType,$(NoTitle),$(!REG_VT_DWORD),1},+
                {Speed,$(NoTitle),$(!REG_VT_DWORD),0},+
                {FullDuplex,$(NoTitle),$(!REG_VT_DWORD),0},+
                {TransmitPadding,$(NoTitle),$(!REG_VT_DWORD),0},+
                {MACAddressOverride,$(NoTitle),$(!REG_VT_DWORD),0},+
                {NumberOfReceiveDescriptors,$(NoTitle),$(!REG_VT_DWORD),64},+
                {NumberOfTransmitPackets,$(NoTitle),$(!REG_VT_DWORD),64},+
                {NumberOfMapRegisters,$(NoTitle),$(!REG_VT_DWORD),64},+
                {NumberOfCoalesceBuffers,$(NoTitle),$(!REG_VT_DWORD),20},+
                {NetworkAddress,$(NoTitle),$(!REG_VT_SZ),""},+
                }


            Debug-Output "$(InfFile) $(Option): Set HardwareParameterKey = $(NewValueList)"
            Shell  $(UtilityInf), AddValueList, $(HardParameterKey), $(NewValueList)
            ifint $($ShellCode) != $(!SHELL_CODE_OK)
                goto ShellCodeError
            endif

            ifint $(NDIS40) == $(TRUE)
                Set NewValueList =  {+
                    {NdisVersion,$(NoTitle),$(!REG_VT_DWORD),1},+
                    }
            else
                Set NewValueList =  {+
                    {NdisVersion,$(NoTitle),$(!REG_VT_DWORD),0},+
                    }
            endif

            Debug-Output "$(InfFile) $(Option): Set HardwareParameterKey = $(NewValueList)"
            Shell  $(UtilityInf), AddValueList, $(HardParameterKey), $(NewValueList)
            ifint $($ShellCode) != $(!SHELL_CODE_OK)
                goto ShellCodeError
            endif

            set TempProdName = """"$(ProductHardwareName)$(AdapterNumber)""""
            set TempBindForm = $(TempProdName)$(NetRuleHardwareBindForm)
            set NewValueList = {{type,$(NoTitle),$(!REG_VT_SZ),$(NetRuleHardware$(Option)Type)},+
                    {bindform,$(NoTitle),$(!REG_VT_SZ),$(TempBindForm)}, +
                    {class,$(NoTitle),$(!REG_VT_MULTI_SZ),$(NetRuleHardware$(Option)Class)}, +
                    {InfOption,$(NoTitle),$(!REG_VT_SZ),$(Option)}}
    
            Debug-Output "$(InfFile) $(Option): HardwareRuleKey = $(NewValueList)"
            Shell  $(UtilityInf), AddValueList, $(HardNetRuleKey), $(NewValueList)
            ifint $($ShellCode) != $(!SHELL_CODE_OK)
                goto ShellCodeError
            endif
            CloseRegKey $(HardNetCardKey)
            CloseRegKey $(HardNetRuleKey)
            CloseRegKey $(HardParameterKey)
        endif    
    EndForListDo
    EndWait
    goto successful

updateparameters =+
    Debug-Output "$(InfFile) $(Option): Updateparameters"
    set HardParameterKey    = $($R3)
    
    ifint $($ShellCode) != $(!SHELL_CODE_OK)
    goto ShellCodeError
    endif
    CloseRegKey $(KeyParameters)
    goto successful

bindingadapter =+
    Debug-Output "$(InfFile) $(Option): bindingadapter"
    set Error = "Binding: Sorry, not yet implemented."
    goto fatal

removeadapter = +
    Debug-Output "$(InfFile) $(Option): removeadapter"
    Debug-Output "$(InfFile) $(Option): ----> $(ProductKeyName), $(!NTN_RegBase)"
    Ifstr(i) $(ProductKeyName) == $(!NTN_RegBase)
        Shell $(UtilityInf), RemoveSoftwareComponent, $(Manufacturer), +
        $(ProductSoftwareName)
        ifint $($ShellCode) != $(!SHELL_CODE_OK)
        goto ShellCodeError
        endif
        set RegistryErrorIndex = $($R0)
    Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
        goto fatalregistry
    endif
    else
    Shell $(UtilityInf), RemoveHardwareComponent, $(Manufacturer), +
        $(ProductSoftwareName), $(!NTN_RegBase)
    ifint $($ShellCode) != $(!SHELL_CODE_OK)
        goto ShellCodeError
    endif
    set RegistryErrorIndex = $($R0)
    Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
        goto fatalregistry
    endif
    endif
    goto end

UpgradeSoftware = +
    Debug-Output "$(InfFile) $(Option): UpdateSoftware"
     OpenRegKey $(!REG_H_LOCAL) "" $(ProductKeyName) $(MAXIMUM_ALLOWED) KeyProduct
     Ifstr $(KeyProduct) != $(KeyNull)
       Shell $(UtilityInf), GetInfFileNameFromRegistry, $(KeyProduct)
       ifint $($ShellCode) != $(!SHELL_CODE_OK)
           Debug-Output "ShellCode error"
           goto ShellCodeError
       endif
       set !UG_Filename = $($R0)
       install "Install-Update"
       ifstr(i) $(STF_INSTALL_OUTCOME) != STF_SUCCESS
           goto fatal
       endif
       SetRegValue $(KeyProduct) {MajorVersion,$(NoTitle),$(!REG_VT_SZ),$(ProductMajorVersion)}
       SetRegValue $(KeyProduct) {MinorVersion,$(NoTitle),$(!REG_VT_SZ),$(ProductMinorVersion)}
       CloseRegKey $(KeyProduct)
     else
       goto fatalregistry
     endif
     goto end

successful = +
    Debug-Output "$(InfFile) $(Option): Successful"
    goto end

abandon = +
    Debug-Output "$(InfFile) $(Option): Abandon"
    ForListDo $(OEM_ABANDON_OPTIONS)
    Shell $(UtilityInf), RemoveHardwareComponent, $(Manufacturer), +
        $(ProductSoftwareName), $($)
    ifint $($ShellCode) != $(!SHELL_CODE_OK)
        goto ShellCodeError
    endif
    set RegistryErrorIndex = $($R0)
    Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
        goto fatalregistry
    endif
    EndForListDo
    Ifstr(i) $(OEM_ABANDON_SOFTWARE) == TRUE
    Shell $(UtilityInf), RemoveSoftwareComponent, $(Manufacturer), +
        $(ProductSoftwareName), FALSE
    ifint $($ShellCode) != $(!SHELL_CODE_OK)
        goto ShellCodeError
    endif
    set RegistryErrorIndex = $($R0)
    Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
        goto fatalregistry
    endif
    endif
    goto end

warning = +
    Debug-Output "$(InfFile) $(Option): warning"
    Shell $(subroutineinf) SetupMessage, $(!STF_LANGUAGE), "WARNING", $(Error)
    ifint $($ShellCode) != $(!SHELL_CODE_OK)
    goto ShellCodeError
    endif
    ifstr(i) $($R1) == "OK"
    goto $(to)
    else-ifstr(i) $($R1) == "CANCEL"
    goto $(from)
    else
    goto "end"
    endif

nonfatalinfo = +
    Debug-Output "$(InfFile) $(Option): nonfatalinfo"
    Set CommonStatus = STATUS_USERCANCEL
    Set Severity = STATUS
    goto nonfatalmsg

nonfatal = +
    Debug-Output "$(InfFile) $(Option): nonfatal"
    Set Severity = NONFATAL
    goto nonfatalmsg

nonfatalmsg = +
    Debug-Output "$(InfFile) $(Option): nonfatalmsg"
    ifstr(i) $(Error) == ""
    Set Severity = NONFATAL
    Shell $(UtilityInf) RegistryErrorString "SETUP_FAIL"
    ifint $($ShellCode) != $(!SHELL_CODE_OK)
        goto ShellCodeError
    endif
    set Error = $($R0)
    endif
    Shell $(subroutineinf) SetupMessage, $(!STF_LANGUAGE), $(Severity), $(Error)
    ifint $($ShellCode) != $(!SHELL_CODE_OK)
    goto ShellCodeError
    endif
    ifstr(i) $($R1) == "OK"
    goto $(from)
    else
    ;   goto "end"
    goto "RemoveAdapter"
    endif

fatalregistry = +
    Debug-Output "$(InfFile) $(Option): fatalregistry"
    Shell $(UtilityInf) RegistryErrorString $(RegistryErrorIndex)
    ifint $($ShellCode) != $(!SHELL_CODE_OK)
    goto ShellCodeError
    endif
    set Error = $($R0)
    goto fatal

fatal = +
    Debug-Output "$(InfFile) $(Option): fatal"
    ifstr(i) $(Error) == ""
    Shell $(UtilityInf) RegistryErrorString "SETUP_FAIL"
    ifint $($ShellCode) != $(!SHELL_CODE_OK)
        goto ShellCodeError
    endif
    set Error = $($R0)
    endif
    Shell $(subroutineinf) SetupMessage, $(!STF_LANGUAGE), "FATAL", $(Error)
    ifint $($ShellCode) != $(!SHELL_CODE_OK)
    goto ShellCodeError
    endif
    goto setfailed

ShellCodeError = +
    Debug-Output "$(InfFile) $(Option): ShellCodeError"
    set DlgType      = "MessageBox"
    set STF_MB_TITLE = $(ShellCodeErrorTitle)
    set STF_MB_TEXT  = $(ShellCodeErrorText) 
    set STF_MB_TYPE  = 1
    set STF_MB_ICON  = 3
    set STF_MB_DEF   = 1
    ui start "Error Message"
    goto setfailed

setfailed = +
    Debug-Output "$(InfFile) $(Option): Setfailed"
    set CommonStatus = STATUS_FAILED
    ifstr(i) $(OEM_ABANDON_ON) == TRUE
    set OEM_ABANDON_ON = FALSE
    goto abandon
    endif
    goto end

end = +
    goto term

term = +
    Return $(CommonStatus)
    
[Install-Option]
    set STF_VITAL = ""
    ifstr(i) $(AddCopy) == "YES"
    AddSectionFilesToCopyList Files-$(FileName) $(SrcDir) $(!STF_WINDOWSSYSPATH)\drivers
    endif
    ifstr(i) $(DoCopy) == "YES"
       set !STF_NCPA_FLUSH_COPYLIST = TRUE
       CopyFilesInCopyList
    endif
    Exit
    
   
[Install-Update]
   set STF_VITAL    = ""
   set STF_OVERWRITE    = "VERIFYSOURCEOLDER"
   AddSectionFilesToCopyList Files-Inf $(SrcDir) $(!STF_WINDOWSSYSPATH)
   AddSectionFilesToCopyList Files-$(FileName) $(SrcDir)\ $(!STF_WINDOWSSYSPATH)\drivers
   set !STF_NCPA_FLUSH_COPYLIST = TRUE
   CopyFilesInCopyList
   exit

[Source Media Descriptions]
    1  = "Windows NT Setup Disk #1"  
    2  = "NSC DP83815 Bus Master Adapter"

[ProductType]
STF_PRODUCT  = Winnt
STF_PLATFORM = I386

[Files-Inf]
2, oemsetup.inf,    SIZE=10000,     RENAME=$(!UG_Filename)

;
; Driver files
;
[Files-dp83815]
2,dp83815.SYS , SIZE=88888

[Files-dp83815nt]
2,dp83815nt.SYS , SIZE=88888 , RENAME=dp83815.SYS

[LanguagesSupported]
    ENG

[OptionsTextENG]
    dp83815   = "NSC DP83815 Adapter"

[FileConstantsENG]
    ProCaption   = "Windows NT v3.5 Setup"
    ProCancel    = "Cancel"
    ProCancelMsg = "Windows NT Networking is not correctly installed.  "+
               "Are you sure you want to cancel copying files?"
    ProCancelCap = "Network Setup Message"
    ProText1     = "Copying:"
    ProText2     = "To:"

ConnectionList  = ^(ConnectionChoices$(Option), 1)
ConnectionValues = ^(ConnectionChoices$(Option), 2)
NoList  = ^(NoChoices, 1)
NoValues = ^(NoChoices, 2)
ShellCodeErrorTitle = "Error: "$(Function$(Option)Title)
ShellCodeErrorText  = "Shell Code Error."
CANNOT_FIND_ANY_CARD    = "Network card is not present in the system"

[DialogConstantsENG]
Help        = "&Help"
Exit        = "Cancel"
OK      = "OK"
HelpContext = ""
Continue    = "Continue"
Cancel      = "Cancel"

Download Driver Pack

How To Update Drivers Manually

After your driver has been downloaded, follow these simple steps to install it.

  • Expand the archive file (if the download file is in zip or rar format).

  • If the expanded file has an .exe extension, double click it and follow the installation instructions.

  • Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.

  • Find the device and model you want to update in the device list.

  • Double-click on it to open the Properties dialog box.

  • From the Properties dialog box, select the Driver tab.

  • Click the Update Driver button, then follow the instructions.

Very important: You must reboot your system to ensure that any driver updates have taken effect.

For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.

server: ftp, load: 1.61