;- This file gives examples of load and bind statements to add to ;- your AUTOEXEC.NCF file for setting up Advanced Network Services ;- on Intel(R) PRO Ethernet adapters. # CONTENTS # Example 1: 2 Adapter Fault Tolerant Team (Pro/1000 and PRO/100 Server) # Example 2: 2 Adapter ALB Team with 2 PROTOCOLS (E_II Frame TYPE) # Example 3: 2 TEAMS - 2 adapter AFT team and 4 Adapter FEC team # Example 4: 1 Adapter, 4 FrameTypes, 2 802.1q VLANs (id 5 and 6), 2 Protocols # Example 5: 2 Adapter ALB team, 5 VLANs, 1 Frame Type, 2 Protocols # Example 6: 2 TEAMS - 2 adapter AFT team and 4 Adapter 802.3ad team ############################################################################### # Example 1: 2 Adapter Fault Tolerant Team (Gigabit and PRO/100 Server) # The following is an example of an AFT team that consists of a gigabit adapter # and a PRO/100 adapter. The Gigabit is the primary and the PRO/100 is the # secondary. For the sake of simplicity, only one frame type, the default of # 802.2, is used. Because the default frame type is used, it does not need to # be specified on the command line. It is also assumed that only one instance # of each adapter is present in the system so a slot number does not need to # be specified. ; First the base driver must be loaded for each adapter and frame type involved ; in the team. As this example only uses 802.2, each adapter only has it's ; base driver loaded once. load CE1000 load CE100B ; Second step is to load IANS.LAN to form the basis of a team. For this ; example IANS is only loaded once. If multiple frame types are used, iANS ; is loaded once for each frame type. load IANS ; Once IANS.LAN is loaded, it looks like a protocol, so we can bind it to the ; physical adapter. IANS.LAN needs to be bound to each physical adapter in ; the team. The "PRIMARY" keyword is used to make iANS favor one particular ; adapter. If a team loses the connection on it's primary adapter it will ; switch to the other adapter(s). If the primary adapter recovers, iANS : will switch back to it. In mixed speed teams always set the fastest ; adapter in the team as the primary. bind IANS CE1000 PRIMARY bind IANS CE100B ; The commit command creates the team. The default mode is AFT. Since ; that is what this example is after, we do not need to specify a mode. load IANS COMMIT ; Once the team has been committed, it looks like an adapter, so now we can ; bind protocols to IANS. bind IPX IANS net=102 ############################################################################### # Example 2: 2 Adapter ALB Team with 2 PROTOCOLS (E_II Frame TYPE) # This example is slightly more complicated. It still only uses one frame # type, but it uses Ethernet_II, which is not the default and must be specified. # It will be a load balanced team (ALB) of PRO/100 adapters and have both IPX # and IP bound to the IANS team. This example assumes a server with 2 PRO/100 # adapters, one in PCI slot 1 and the other in PCI slot 2. ;Load TCPIP.NLM. This can be done at any point before binding IP. load TCPIP ; Load the base drivers for each adapter in the team. Since the default frame ; type (802.2) is not the one in use, the frame type (Ethernet_II) must be ; specified on the driver load line. Also, as two different PRO/100 adapters ; are in use, each one needs to be assigned a name for later reference. load CE100B slot=1 frame=ETHERNET_II name=Primary_CE100B_II load CE100B slot=2 frame=ETHERNET_II name=Scndary_CE100B_II ; Load IANS.LAN to form the groundwork for the team. Again, the frame type ; needs to be specified as it is not the default. If multiple frame types, ; multiple VLANs or multiple teams get used then this command requires that ; a "name" is issued for each instance of IANS. In this example a "name" ; for the team is optional. load IANS frame=ETHERNET_II ; Bind IANS.LAN to each physical adapter using the names we defined when ; the base drivers were loaded bind IANS Primary_CE100B_II bind IANS Scndary_CE100B_II ; Create the team in load balancing mode. load IANS COMMIT MODE=ALB ; bind both IPX and IP as if IANS was a physical adapter. bind IPX IANS net=111 bind IP IANS Address=192.168.1.1 Mask=255.255.255.0 ############################################################################### # Example 3: 2 TEAMS - 2 adapter AFT team and 4 Adapter FEC team # This example will make 2 teams. The first will be a fault tolerant team of # a Gigabit Server Adapter (CE1000.LAN) and a PRO/100 (CE100B.LAN). The second # team will consist of four PRO/100 adapters (CE100B.LAN) configured as a "Fast # Ether Channel" team. Note that the term "Fast Ether Channel" is a term that # refers to Cisco's implementation of 100MB port aggregation. With Gigabit # teams it would technically be called "Gigabit Ether Channel", or "GEC". This # example uses IPX on both Ethernet 802.2 and Ethernet II. It also uses IP on # Ethernet II. ;load TCPIP.NLM. Must be done before IP is bound. LOAD TCPIP ; Load the base drivers for the first team. LOAD CE1000 SLOT=1 FRAME=Ethernet_802.2 NAME=GIG_E82 LOAD CE1000 SLOT=1 FRAME=Ethernet_II NAME=GIG_EII LOAD CE100B SLOT=2 FRAME=Ethernet_802.2 NAME=100M_E82 LOAD CE100B SLOT=2 FRAME=Ethernet_II NAME=100M_EII ; Load IANS.LAN for the first team. The team number is included on the command ; line here. If "TEAM=1" is not included, IANS will default to team 1, so for ; this portion of the example, the "TEAM" command line switch is optional. LOAD IANS FRAME=ETHERNET_802.2 NAME=GIG_FT_E82 TEAM=1 LOAD IANS FRAME=ETHERNET_II NAME=GIG_FT_EII TEAM=1 ; Bind IANS to the base driver for each adapter and each frame type. Bind to ; the name of the base driver instance (assigned when the driver was loaded) ; and specify the team number. BIND IANS GIG_E82 TEAM=1 PRIMARY BIND IANS GIG_EII TEAM=1 PRIMARY BIND IANS 100M_E82 TEAM=1 BIND IANS 100M_EII TEAM=1 ; commit for team 1 LOAD IANS COMMIT MODE=AFT TEAM=1 ; Bind IPX to both frame types and bind IP to Ethernet II. BIND IPX GIG_FT_E82 NET=102 BIND IPX GIG_FT_EII NET=111 BIND IP GIG_FT_EII ADDR=128.181.11.1 MASK=255.255.255.0 ; Now load the base drivers for the second team (FEC). LOAD CE100B SLOT=6 FRAME=Ethernet_802.2 NAME=FEC_1_E82 LOAD CE100B SLOT=6 FRAME=Ethernet_II NAME=FEC_1_EII LOAD CE100B SLOT=5 FRAME=Ethernet_802.2 NAME=FEC_2_E82 LOAD CE100B SLOT=5 FRAME=Ethernet_II NAME=FEC_2_EII LOAD CE100B SLOT=4 FRAME=Ethernet_802.2 NAME=FEC_3_E82 LOAD CE100B SLOT=4 FRAME=Ethernet_II NAME=FEC_3_EII LOAD CE100B SLOT=3 FRAME=Ethernet_802.2 NAME=FEC_4_E82 LOAD CE100B SLOT=3 FRAME=Ethernet_II NAME=FEC_4_EII ; Load IANS.LAN for the second team. Name each frame type with the "NAME" ; keyword and specify the second team with the "TEAM=2" keyword. LOAD IANS FRAME=ETHERNET_802.2 NAME=FEC_TEAM_E82 TEAM=2 LOAD IANS FRAME=ETHERNET_II NAME=FEC_TEAM_EII TEAM=2 ; Bind IANS to the base driver for each adapter and each frame type. Bind to ; the name of the base driver instance (assigned when the driver was loaded) ; and specify the team number. bind IANS FEC_1_E82 TEAM=2 bind IANS FEC_1_EII TEAM=2 bind IANS FEC_2_E82 TEAM=2 bind IANS FEC_2_EII TEAM=2 bind IANS FEC_3_E82 TEAM=2 bind IANS FEC_3_EII TEAM=2 bind IANS FEC_4_E82 TEAM=2 bind IANS FEC_4_EII TEAM=2 ; commit for team 2 LOAD IANS COMMIT MODE=FEC TEAM=2 ; Bind IPX to both frame types and bind IP to Ethernet II. BIND IPX FEC_TEAM_E82 NET=202 BIND IPX FEC_TEAM_EII NET=211 BIND IP FEC_TEAM_EII ADDR=128.181.22.1 MASK=255.255.255.0 ############################################################################### # Example 4: 1 Adapter, 4 FrameTypes, 2 802.1q VLANs, 2 Protocols # Now for VLAN... # In order to use iANS.LAN in VLAN mode, the adapter (or adapters) need to # be connected to a "tagged" port on an IEEE 802.1Q compliant switch. This # example uses 802.1Q VLAN which is supported by all new Intel adapters and # most of the older ones. It will use a single 8255x based adapter and be # configured for two VLANs, VLAN id 5 and VLAN id 6. It will also use all # four NetWare frame types and bind both the IPX and IP protocols. ;load TCPIP.NLM. Must be done before IP is bound. LOAD TCPIP ; load the base driver for each frame type load ce100b slot=5 frame=ethernet_802.2 name=e82 load ce100b slot=5 frame=ethernet_802.3 name=e83 load ce100b slot=5 frame=ethernet_snap name=esp load ce100b slot=5 frame=ethernet_ii name=eii ; load ians and specify the vlanid for each frame type and each VLAN the ; server is supposed to be part of. On a single team configuration "team=1" ; is optional as that is the default setting. ; First ians is loaded for vlan 5, assigning a name of 5xx to each instance. load ians vlanid=5 frame=ethernet_802.2 name=582 team=1 load ians vlanid=5 frame=ethernet_802.3 name=583 team=1 load ians vlanid=5 frame=ethernet_snap name=5sp team=1 load ians vlanid=5 frame=ethernet_ii name=5ii team=1 ; Then ians is loaded for vlan 6, assigning a name of 6xx to each instance. load ians vlanid=6 frame=ethernet_802.2 name=682 team=1 load ians vlanid=6 frame=ethernet_802.3 name=683 team=1 load ians vlanid=6 frame=ethernet_snap name=6sp team=1 load ians vlanid=6 frame=ethernet_ii name=6ii team=1 ; After loading ians for all the desired VLANs, bind ians to the base driver ; using the name that was defined when the base drivers were originally loaded. bind ians e82 team=1 bind ians e83 team=1 bind ians esp team=1 bind ians eii team=1 ; Now the team can be created with an ians commit command. load ians commit team=1 ; and protocols can be bound to each instance (VLAN and frame type) of ians in ; the same manner as if they were being bound to a physical adapter. bind ipx 582 net=502 bind ipx 583 net=503 bind ipx 5sp net=505 bind ipx 5ii net=511 bind ip 5ii addr=192.168.52.1 mask=ff.ff.ff.0 bind ipx 682 net=602 bind ipx 683 net=603 bind ipx 6sp net=605 bind ipx 6ii net=611 bind ip 6ii addr=192.168.62.1 mask=ff.ff.ff.0 ############################################################################### # Example 5: 2 Adapter ALB team, 5 VLANs, 1 Frame Type, 2 Protocols # Teaming and VLAN can be implemented at the same time. The script gets # large quickly so this example will only use one frame type. So that both IP # and IPX can be bound to it, the Ethernet_II frame type will be used instead # of Novell's default 802.2. A homogenous team of 2 load balanced PRO/100 # Server adapters configured as members of 5 different VLANs will be used here. ; load TCPIP.NLM. Must be done before IP is bound. LOAD TCPIP ; Load the base drivers for each adapter in the team. LOAD CE100B SLOT=1 FRAME=ETHERNET_II NAME=Primary_II LOAD CE100B SLOT=2 FRAME=ETHERNET_II NAME=Secondary_II ; Load IANS.LAN with the VLANID keyword once for each VLAN that the server is ; intended to communicate with. Assign a name so that each instance can ; referenced when binding the network protocols. LOAD IANS FRAME=ETHERNET_II VLANID=10 NAME=V10 TEAM=1 LOAD IANS FRAME=ETHERNET_II VLANID=20 NAME=V20 TEAM=1 LOAD IANS FRAME=ETHERNET_II VLANID=30 NAME=V30 TEAM=1 LOAD IANS FRAME=ETHERNET_II VLANID=40 NAME=V40 TEAM=1 LOAD IANS FRAME=ETHERNET_II VLANID=50 NAME=V50 TEAM=1 ; Bind ians to each physical adapter. BIND IANS PRIMARY_II PRIMARY BIND IANS SECONDARY_II ; Create the team in load balancing mode. LOAD IANS COMMIT MODE=ALB ; And bind both IPX and IP to iANS for each VLAN. ;IPX first BIND IPX V10 NET=1011 BIND IPX V20 NET=2011 BIND IPX V30 NET=3011 BIND IPX V40 NET=4011 BIND IPX V50 NET=5011 ;and IP BIND IP V10 ADDR=23.17.10.1 MASK=FF.FF.0.0 BIND IP V20 ADDR=23.18.20.1 MASK=FF.FF.0.0 BIND IP V30 ADDR=23.19.30.1 MASK=FF.FF.0.0 BIND IP V40 ADDR=23.20.40.1 MASK=FF.FF.0.0 BIND IP V50 ADDR=23.21.50.1 MASK=FF.FF.0.0 ############################################################################### # Example 6: 2 TEAMS - 2 adapter AFT team and 4 Adapter 802.3ad team # This example will make 2 teams. The first will be a fault tolerant team # of a Gigabit Server Adapter (CE1000.LAN) and a PRO/100 (CE100B.LAN). The # second team will consist of four PRO/100 adapters (CE100B.LAN) configured # as a 802.3ad team. This example uses IPX on both Ethernet 802.2 and # Ethernet II. It also uses IP on Ethernet II. ;load TCPIP.NLM. Must be done before IP is bound. LOAD TCPIP ; Load the base drivers for the first team. LOAD CE1000 SLOT=1 FRAME=Ethernet_802.2 NAME=GIG_E82 LOAD CE1000 SLOT=1 FRAME=Ethernet_II NAME=GIG_EII LOAD CE100B SLOT=2 FRAME=Ethernet_802.2 NAME=100M_E82 LOAD CE100B SLOT=2 FRAME=Ethernet_II NAME=100M_EII ; Load IANS.LAN for the first team. The team number is included on the command ; line here. If "TEAM=1" is not included, IANS will default to team 1, so for ; this portion of the example, the "TEAM" command line switch is optional. LOAD IANS FRAME=ETHERNET_802.2 NAME=GIG_FT_E82 TEAM=1 LOAD IANS FRAME=ETHERNET_II NAME=GIG_FT_EII TEAM=1 ; Bind IANS to the base driver for each adapter and each frame type. Bind to ; the name of the base driver instance (assigned when the driver was loaded) ; and specify the team number. BIND IANS GIG_E82 TEAM=1 PRIMARY BIND IANS GIG_EII TEAM=1 PRIMARY BIND IANS 100M_E82 TEAM=1 BIND IANS 100M_EII TEAM=1 ; commit for team 1 LOAD IANS COMMIT MODE=AFT TEAM=1 ; Bind IPX to both frame types and bind IP to Ethernet II. BIND IPX GIG_FT_E82 NET=102 BIND IPX GIG_FT_EII NET=111 BIND IP GIG_FT_EII ADDR=128.181.11.1 MASK=255.255.255.0 ; Now load the base drivers for the second team (AD). LOAD CE100B SLOT=6 FRAME=Ethernet_802.2 NAME=AD_1_E82 LOAD CE100B SLOT=6 FRAME=Ethernet_II NAME=AD_1_EII LOAD CE100B SLOT=5 FRAME=Ethernet_802.2 NAME=AD_2_E82 LOAD CE100B SLOT=5 FRAME=Ethernet_II NAME=AD_2_EII LOAD CE100B SLOT=4 FRAME=Ethernet_802.2 NAME=AD_3_E82 LOAD CE100B SLOT=4 FRAME=Ethernet_II NAME=AD_3_EII LOAD CE100B SLOT=3 FRAME=Ethernet_802.2 NAME=AD_4_E82 LOAD CE100B SLOT=3 FRAME=Ethernet_II NAME=AD_4_EII ; Load IANS.LAN for the second team. Name each frame type with the "NAME" ; keyword and specify the second team with the "TEAM=2" keyword. LOAD IANS FRAME=ETHERNET_802.2 NAME=AD_TEAM_E82 TEAM=2 LOAD IANS FRAME=ETHERNET_II NAME=AD_TEAM_EII TEAM=2 ; Bind IANS to the base driver for each adapter and each frame type. Bind to ; the name of the base driver instance (assigned when the driver was loaded) ; and specify the team number. bind IANS AD_1_E82 TEAM=2 bind IANS AD_1_EII TEAM=2 bind IANS AD_2_E82 TEAM=2 bind IANS AD_2_EII TEAM=2 bind IANS AD_3_E82 TEAM=2 bind IANS AD_3_EII TEAM=2 bind IANS AD_4_E82 TEAM=2 bind IANS AD_4_EII TEAM=2 ; commit for team 2 LOAD IANS COMMIT MODE=AD TEAM=2 ; Bind IPX to both frame types and bind IP to Ethernet II. BIND IPX AD_TEAM_E82 NET=202 BIND IPX AD_TEAM_EII NET=211 BIND IP AD_TEAM_EII ADDR=128.181.22.1 MASK=255.255.255.0 ###############################################################################Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.