1. clrvsn02.zip Driver
2. INSTALL.TXT File Contents

INSTALL.TXT Driver File Contents (clrvsn02.zip)

 
June 1997

clearVISN Version 1.1A Support Kit Installation Procedure


Introduction

The clearVISN V1.1A software support kit enables you to use Multichassis Manager V6.0A to 
manage the VNswitch 900XX and the MultiSwitch 612EX. The support kit includes the 
following four files:

 hwlitestack.dll

 switchvw.dll

 swsum.dll

 hw_mib.dat

Hardware and Software Requirements

Before installing the support kit files, make sure you have the latest hardware and 
software versions:

 DEChub 900 MAM V5.1 

 MultiSwitch  612EX V1.1 

 VNswitch 900EE/EF/EA V1.5 

 VNswitch 900XX V1.6 

 clearVISN V1.1A (MultiChassis Manager V6.0A)



The  VNSwitch 900XX and MultiSwitch 612EX firmware and required dcffiles.dat files are 
located at the following URLs:


VNSwitch 900XX											

Americas	http://www.networks.digital.com/dr/vnswitch/firmware

Europe 		http://www.networks.europe.digital.com/dr/vnswitch/firmware

Australia 	http://www.networks.digital.com.au/dr/vnswitch/firmware



MultiSwitch 612EX			

Americas	http://www.networks.digital.com/dr/hubs/firmware/index.html

Europe	 	http://www.networks.europe.digital.com/dr/hubs/firmware/index.html

Australia 	http://www.networks.digital.com.au/dr/hubs/firmware/index.html



You must copy the firmware and dcffiles.dat files to the \clearvis\firmware directory.

Note:

This information is also available on the DIGITAL Network Product Business Bulletin Board. 
To connect, you need a PC and a modem. Dial 508-486-5777  (U.S.A.) or after October 1, 1997, 
dial 978-486-5777 (U.S.A).  Set your modem to 8 bits, no parity, 1 stop bit.



Installing the Support Kit

 Use the following procedure to copy the files: 


1  You must have clearVISN V1.1A installed.  Also, you must have opened 
   Multichassis Manager at least once before performing this procedure.  
   If MultiChassis Manager is running, close the application before installing 
   the files.

2  Find the directory where MultiChassis Manager resides. By default, the directory
   is \clearVIS\hubwatch.

3  Create backup copies of the following files in this directory:

 hwlitestack.dll

 switchvw.dll

 swsum.dll

 hw_mib.dat

4 If you are installing from the Internet, locate the following URL, 
  depending on your location:

 Americas			http://www.networks.digital.com/dr/clearvsn				  

 Europe 			http://www.networks.europe.digital.com/dr/clearvsn	

 Australia 			http://www.networks.digital.com.au/dr/clearvsn	

If you are installing this kit from a diskette, go to step 6.


5  From the clearVISN home page, select "Patches and Upgrades."

6  Download or copy the four  files to the directory where MultiChassis 
   Manager resides.   By default, the directory is \clearVIS\hubwatch.

7  Edit the hubwatch.ini file.  Locate the following line in the file:  

 	 Switch Summary - VN900FEMX=212,swsum.dll

8  Insert the following line below the previous line, making sure 
	  to keep the same case.

  	 Switch Summary - VN900XX=213,swsum.dll


Notes:

• This line launches the Switch  Summary window when you double click the VNswitch 900XX 
	front bezel from the MultiChassis Manager front panel. 

• MultiChassis Manager will create a new hubwatch.ini file if one does not exist.
	 If this happens, repeat step 7.

 
9 You can now use MultiChassis Manager V6.0A to manage the VNswitch 900XX 
  and MultiSwitch  612EX, without rebooting your pc.













© Digital Equipment Corporation 1997. All rights reserved. 

Digital, and the DIGITAL logo are trademarks of Digital Equipment Corporation.