NSC DP83815 10/100Mbps MacPhyter3v PCI Adapter Installtion
for NetWare DOS ODI Driver
Contents
ÍÍÍÍÍÍÍÍ
Introduction
Getting Started
First installation from CD-ROM
Manual Installation
How to create Diskettes for installation
Introduction
ÍÍÍÍÍÍÍÍÍÍÍÍ
The ODI driver program allows you to run multiple protocol
stacks and install up to two network adapters in a workstation.
This ODI driver supports the Port, Node Address, Protocol and
Frame options for creating your own NET.CFG file. For more
information on these keywords, please refer to Novell's
"NetWare ODI shell for DOS - NET.CFG options".
Getting Started will describe the installation instructions.
Getting Started
ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ
The NOVELL installation diskettes or CD-ROM are needed to
complete this install.
First installation from CD-ROM
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
Please make sure CD-ROM drive work fine under DOS environment.
Run INSTALL.BAT and press any key to accept the agreement.
Ex. >INSTALL
Select "Client Installation" in Select the type of installation
desired window.
Select "NetWare DOS/WINDOWS Client (VLM)" in Select Client to
be installed window.
Specify your target directory, installation default path is
C:\NWCLIENT. (suggestion: DON'T change it)
Allow system to modified your AUTOEXEC.BAT and CONFIG.SYS.
Specify YES to install support for MS Windows, if you accept.
Move the highlight bar to Select the driver for your network
board and press <Enter>.
Put the driver diskette into floppy disk drive and go to bottom.
Select "OTHER DRIVERS" under Network Board.
Specify the full path of ODI for DOS driver.
Ex. A:\NETWARE\DOSODI
Select "NSC DP83815 MacPhyter".
Specify "Media Frame Type(s)", then press "F10" to save/continue.
Move to "Highlight here and press <Enter> to install".
Press <Enter> after you configure it correctly, then
installation will copy necessary files to your hard disk.
Restart your system and connect to NetWare server.
Manual Installation
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
Assume you have installed NetWare Client for DOS system.
Copy <PATH>\C83815.COM file from driver diskette into the
Netware client directory containing LSL.COM, IPXODI.COM,
NETx.COM or VLM.COM, VLM files.
Ex. >COPY A:\NETWARE\DOSODI\C83815.COM C:\NWCLIENT
A typical Client for DOS startup batch file includes:
Content of STARTNET.BAT
-----------------------
SET NWLANGUAGE=English
C:\NWCLIENT\LSL.COM
C:\NWCLIENT\C83815.COM
C:\NWCLIENT\IPXODI.COM
C:\NWCLIENT\VLM.EXE
F: ; According FIRST NETWORK DRIVE of
; NET.CFG
LOGIN XXXX ; Login to server, XXXX is user name
; Notes: C:\NWCLIENT\VLM.EXE /PS=SSSS ; SSSS is server name
Content of NET.CFG
------------------
Link Driver C83815
SLOT 1
FRAME ETHERNET_802.2
FRAME ETHERNET_802.3
FRAME ETHERNET_II
FRAME ETHERNET_SNAP
NetWare DOS Requester
FIRST NETWORK DRIVE = F
NETWARE PROTOCOL = NDS BIND
How to creat Diskettes for installation
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
Please make sure CD-ROM drive work fine under DOS environment.
Run INSTALL.BAT and press any key to accept the agreement.
Ex. >INSTALL
Select "Diskette Creation" in Select the type of installation
desired window.
Select "NetWare DOS/WINDOWS Client (VLM)" in Select the
Diskette set to be created window.
Follow the screen's instructions.
NET.CFG parameters for C83815.COM
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
NWAY - This keyword operate in NWay Auto-negotiation
to determine the network speed and the duplex
mode of the network connection. (Default)
N100F - This keyword forces to operate in 100M Full-Duplex
Nway Capability.
N100H - This keyword forces to operate in 100M Half-Duplex
Nway Capability.
N10F - This keyword forces to operate in 10M Full-Duplex
Nway Capability.
N10H - This keyword forces to operate in 10M Half-Duplex
Nway Capability.
100F - This keyword forces to operate in 100M Full-Duplex
Media Mode.
100H - This keyword forces to operate in 100M Half-Duplex
Media Mode.
10F - This keyword forces to operate in 10M Full-Duplex
Media Mode.
10H - This keyword forces to operate in 10M Half-Duplex
Media Mode.
SLOT - This keyword select Slot Number.
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.