1. sp2500k.zip Driver
2. README.TXT File Contents

README.TXT Driver File Contents (sp2500k.zip)

                  Micronet SP2500K 10/100 PCI FAST ETHERNET ADAPTER
===============================================================================


How to Configure Your PCI adapter
---------------------------------
 1. Go to the PCI configuration item in BIOS setup.
 2. Take the following steps to configure the PCI slot:
   a).  You should know which slot your adapter is plugged into.
        Look for the physical location of the slot on your PCI
        motherboard.
   b).  Set the "this device" field to "Enable".
   c).  Set the "this item" field to "Master".
        The Micronet SP2500K PCI adapter MUST be installed
        in an expansion slot that supports "Bus Master" mode.
        Refer to your system documentation to determine which slots
        support Bus Mastering.
   d).  Some BIOS Setups allow you to select which interrupt line
        you can use.  In this case, select "INT A" for the "this item" field.
   e).  Select an IRQ of your choice, make sure it does not conflict
        with existing IRQs in use.
   d).  Select the "Trigger method" by which the IRQ is assigned or
        routed to the PCI slot.  Choose "level-trigger" option.
        Multiple SP2500K PCI adapters can share the same PCI
        interrupt and all must use INT A with level-trigger mode.

 3. Run the diagnostic program found in the driver diskette.
    If a problem arises during installation, contact your dealer for support.


Conflict with Microsoft EMM386
------------------------------

The PCI adapters can only function with the EMM386.exe memory manager
program version 4.49 or later. You can verify its version number by
entering EMM386 at the DOS Prompt.

Do not specify the "highscan" option with the EMM386.exe statement
in your config.sys file or your system will hang.

If you run MEMMAKER and select Custom Setup, do not specify
"Aggressively scan upper memory", or it will automatically insert
the HIGHSCAN flag into the EMM386 command line. This parameter cannot
be manually removed once it's installed; doing so will cause the
extended memory manager to malfunction.


Support for 5 Volt PCI Slots
----------------------------

The Micronet SP2500K 10/100 PCI Fast Ethernet Adapter currently supports
only 5 volt PCI slots. Future release of the adapter will support both
3.3 and 5 volt PCI slots.


Note: 1.  Some PCI-ISA computers require manual configuration.  When you
          set the interrupt you must move the jumper.  For example,
          if you set INT A to interrupt 5 via a BIOS configuration
          setting, you must also set the jumper on your motherboard to ISA
          interrupt 5.
      2.  Usually, the PCI machine supports only two Master Devices.
          SCSI devices are also master devices.

*This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1)This device may not cause harmful interference, and
(2)this device must accept any interference received,
including interference that may cause undesired operation.

This Federal Communications Commission Statement
  This equipment has been tested and found to comply with the limits for a
  Class B digital device, pursuant to part 15 of the FCC Rules. These limits
  are designed to provide reasonable protection against harmful interference
  in a residential installation.
  This equipment generates, uses and can radiate radio frequency energy and,
  if not installed and used in accordance with the instructions, may cause
  harmful interference to radio communications.
  However, there is no guarantee that interference will not occur in a
  particular installation.
  If this equipment does cause harmful interference to radio or television
  reception, which can be determined by turning the equipment off and on,
  the user is encouranged to try to correct the interference by one or more
  of the following measures:
  -Reorient or relocate the receiving antenna.
  -Increase the separation between the equipment and receiver.
  -Connect the equipment into an outlet on a circuit different from that to
   which the receiver is connected.
  -Consult the dealer or an experienced radio/TV technician for help.

 You are cautioned that changes or modifications not expressly approved by
 the party responsible for campliance could void your authority to operate
 the equipment.

SAFETY INSTRUCTIONS

1.   Please read these safety instructions carefully.
2.   Please keep this User's Manual for later reference.
3.   Please disconnect this equipment from AC outlet before cleaning.
     Don't use liquid or sprayed detergent for cleaning.
     Use moisture sheet or cloth for cleaning.
4.   For pluggable equipment, the socket-outlet shall be installed near
     the equipment and shall be easily accessible.
5.   Please keep this equipment from humidity.
6.   Lay this equipment on a reliable surface when install.A drop or fall
     could cause injury.
7.   The openings on the enclosure are for air convection hence protect
     the equipment from overheating. DO NOT COVER THE OPENINGS.
8.   Make sure the voltage of the power source when connect the
     equipment to the power outlet.
9.   Place the power cord such a way that people can not step on it. Do
     not place anything over the power cord.
10. All cautions and warnings on the equipment should be noted.
11. If the equipment is not use for long time, disconnect the equipment
    from mains to avoid being damaged by transient overvoltage.
12. Never pour any liquid into opening, this could cause fire or electrical shock.
13. Never open the equipment. For safety reason, the equipment should only
    be opened by qualified service personnel.
14. If one of the following situations arises, get the equipment checked by a
    service personnel:

    a. The power cord or plug is damaged.
    b. Liquid has penetrated into the equipment.
    c. The equipment has been exposed to moisture.
    d. The equipment has not work well or you can not get it work
       according to user's manual.
    e. The equipment has dropped and damaged.
    f. If the equipment has obvious sign of breakage.

15. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT
    UNCONDITIONED: STORAGE TEMPERATURE ABOVE60(140),IT
    MAY DAMAGE THE EQUIPMENT.

16. The sound pressure level at the operators position according to IEC 704-1:
    1982 is equal or less then 70dB(A).

Wichtige Sicherheitshinweise (Germany)
1. Bitte lesen Sie diese Hinweise sorgf„ltig durch.
2. Heben Sie diese Anleitung f�r den sp„teren Gebrauch auf.
3. Vor jedem Reinigen ist das Ger„t vom Stromnetz zu trennen. Verwenden Sie keine
   Fl�ssigoder Aerosolreiniger. Am besten eignet sich ein angefeuchtetes Tuch zur Reinigung.
4. Die Netzanschlu ásteckdose soll nahe dem Ger„t angebracht und leicht zug„nglich sein.
5. Das Ger„t ist vor Feuchtigkeit zu sch�tzen.
6. Bei der Aufstellung des Ger„tes ist auf sicheren Stand zu achten. Ein Kippen oder Fallen
   k”nnte Besch„digungen hervorrufen.
7. Die Bel�ftungs”ffnungen dienen der Luftzirkulation, die das Ger„t vor šberhitzung sch�tzt.
   Sorgen Sie daf�r, daá diese ™ffnungen nicht abgedeckt werden.
8. Beachten Sie beim Anschluá an das Stromnetz die Anschluáwerte.
9. Verlegen Sie die Netzanschluáleitung so, daá niemand dar�ber fallen kann. Es sollte auch
   nichts auf der Leitung abgestellt werden.
10. Alle Hinweise und Warnungen, die sich am Ger„t befinden, sind zu beachten.
11. Wird das Ger„t �ber einen l„ngeren Zeitraum nicht benutzt, sollten Sie es vom Stromnetz
    trennen. Somit wird im Falle einer šberspannung eine Besch„digung vermieden.
12. Durch die L�ftungs”ffnungen d�rfen niemals Gegenst„nde oder Fl�ssigkeiten in das Ger„t
    gelangen. Dies k”nnte einen Brand bzw. elektrischen Schlag ausl”sen.
13. ™ffnen sie niemals das Ger„t. Das Ger„t darf aus Gr�nden der elektrischen Sicherheit nur
    von authorisiertem Servicepersonal ge”ffnet werden.
14. Wenn folgende Situationen auftreten ist das Ger„t vom Stromnetz zu trennen und von einer
    qualifizierten Servicestelle zu �berpr�fen:
    a. Netzkabel oder Netzstecker sind besch„digt.
    b. Fl�ssigkeit ist in das Ger„t eingedrungen.
    c. Das Ger„t war Feuchtigkeit ausgesetzt.
    d. Wenn das Ger„t nicht der Bedienungsanleitung entsprechend funktioniert oder Sie mit Hilfe
       dieser Anleitung keine Verbesserung erzielen.
    e. Das Ger„t ist gefallen und/oder das Geh„use ist besch„digt.
    f. Wenn das Ger„t deutliche Anzeichen eines Defektes aufweist.
15. Zum Netzanschluá dieses Ger„tes ist eine gepr�fte Leitung zu verwenden. F�r einen
    Nennstrom bis 6A und einem Ger„tegewicht gr”áer 3kg ist eine Leitung nicht leichter als
    H05VV-F, 3G, 0.75mm 2 einzusetzen.
    Der arbeitsplatzbezogene Schalldruckpegel nach DIN 45 635 Teil 1000 betr„gt 70dB(A)
    oder weniger.