1. SP2080_RPL.zip Driver
2. RBOOT16.TXT File Contents

RBOOT16.TXT Driver File Contents (SP2080_RPL.zip)

;************************************************************************
;*
;*  Chapter 1. How to use this patch file?
;*
;*      This file (BROOM.TXT) contains info. that helps you patch
;*      'BROOM.ROM'(v3.00) file into your own Boot ROM driver.
;*
;*      To generate your custom driver, please follow the steps
;*      described below:
;*
;*      a). Follow the instructions to edit the message area in each
;*          line. Save this file when you finish editing.
;*          ( see CHAPTER 2 for more details ! )
;*
;*         !!! NOTE: DO NOT EDIT THE OFFSET AND LENGTH AREA !!!
;*
;*      b). Make sure that you have the following files in your working
;*          directory:
;*
;*              RTPATCH.EXE     ------->   The patch execution file
;*              BROOT.ROM       ------->   RTL8029 BOOT ROM driver file
;*              BROOT.TXT       ------->   BOOT ROM patch info. file
;*
;*      c). After you decide the name for your BOOT ROM driver,
;*          simply type:
;*
;*          > rtpatch  BROOM.ROM  BROOM.txt  <put driver name here>  <Ù
;*
;*         !!! NOTE: DO NOT USE THE SAME DRIVER NAME AS THE ORIGINAL
;*                   DRIVER!!!
;*
;*      d). If no error occurs, you should find your custom driver is
;*          generated under your working directory.
;*
;*
;* Chapter 2. How to edit this file ?
;*
;*
;*      Each line in this file contains a display message info. of the
;*      driver. Each line has the same format:
;*
;*          <offset> <length> <message>
;*      e.g.
;*           1266      28    ) 'Packet driver for RTL8029',0dh,0ah,0h;
;*           ----      --      ----------------------------------------
;*                                                                
;*        Do not edit here!       |                                 | EOL
;*                           Put your own message here!           |
;*          (HEX)     (DEC)                                     delimiter
;*
;*
;*
;*      *NOTE: DO NOT EDIT THE <offset> AND <length> AREA !!!
;*
;*      *NOTE: Anything after comment character ';' will be ignored!
;*
;*      *NOTE: Always add ';'(EOL) at end of each line!
;*
;*      *NOTE: If delimiter is needed, keep delimiter intact! In this case,
;*             leave the '0h' as the last byte.
;*
;*      *NOTE: 0H can only be added as delimiter! Message after 0H will be lost!
;*
;*      *NOTE: Total length of your message should not exceed <length>.
;*
;*      *NOTE: If you must use the comment character (;) in your message,
;*             put 3bh instead of ';'.
;*
;*      *NOTE: Do not exceed 250 characters in each line.
;*
;************************************************************************


;************************************************************************
;       Put your driver name here  (no delimiter)
;************************************************************************


;************************************************************************
;       Put your driver title here ( delimiter is '0h')
;************************************************************************
; PCIODI driver short name to display message

553  47  'Novell NetWare Ready Firmware  v3.00 (980108)',0dh,0ah;
582  62  '(C) Copyright 1995 - 1997 Novell, Inc.  All Rights Reserved.',0dh,0ah;
236E 168 'Realtek 8029 PCI Ethernet MLID v6.20 (971113) ',0dh,0ah,'(C) Copyright 1993 - 1997 Realtek Semiconductor Co., LTD. All Rights Reserved.',20h;