README.TXT Driver File Contents (ZEN1100-02.zip)

              README File for PCMCIA 10/100Mbps Fast Ethernet PC Card

Thanks for choosing the PCMCIA 10/100Mbps Fast Ethernet PC Card. 
This card is compliant with the PCMCIA 2.0 Type II standard and 
it provides credit card-sized connectivity solution for portable PC.

                        Driver Diskette Overview

                               TOPIC
                ======================================
                       1.  DISKETTE CONTENTS
                       2.  ENABLE PCMCIA CARD
                       3.  SOCKET and CARD SERVICES INSTALLATION ADVISORY
                       4.  NETWARE DOS ODI DRIVER
                       5.  PACKET DRIVER
                       6.  NDIS DRIVER FOR WINDOWS 95
                       7.  NDIS DRIVER FOR WINDOWS 98
                       8.  NDIS DRIVER FOR WINDOWS ME                       
                       9.  NDIS DRIVER FOR WINDOWS NT 3.51
                      10.  NDIS DRIVER FOR WINDOWS NT 4.0
                      11.  NDIS DRIVER FOR WINDOWS 2000
                      12.  NDIS DRIVER FOR WINDOWS XP

[1] DISKETTE CONTENTS


      Files and
      Subdirectories      Contents
      --------------------------------------------------------------------
      \EN1100CS.EXE        Enable PCMCIA Card Program
      \README.TXT          This file
      \DOSODI              Novell Netware DOS ODI Driver
      \PKTDRV              Packet Driver
      \WIN95               NDIS Driver for Windows 95
      \WIN98               NDIS Driver for Windows 98
      \WINME               NDIS Driver for Windows ME
      \NT351               NDIS Driver for Windows NT 3.51
      \NT40                NDIS Driver for Windows NT 4.0
      \WIN2000             NDIS Driver for Windows 2000
      \WINXP               NDIS Driver for Windows XP

[2] ENABLE PCMCIA CARD (For DOS and Windows 3.1 Only)


      The EN1100CS.EXE is a PCMCIA  controller enable program. This enable
      program only need for DOS and Windows 3.1 system. You should installed
      the Socket and Card service in your Notebook  before executing the
      enable program. If you do not have the Socket or card service program,
      please call the Notebook vendor. The EN1100CS.EXE will keep resident for
      handle card insertion and removal events. This feature can prevent
      system crash when remove the card from socket.
      To enable PCMCIA card, type

          EN1100CS [/IRQ:X][/IOP:XXX][/h]

      in DOS command line, or

          DEVICE=[PATHNAME]EN1100CS.EXE [/IRQ:x][/IOP:XXX][/h]

      in config.sys file.

          where:

          [/IRQ:x]     This specifies the hardware interrupt (IRQ) where your
                       card will be indicated.
                       The valid IRQs are 3,4,5,9,10,12,15.

          [/IOP:XXX]  This specifies the I/O address. The valid ports are
                       300,320,340,360.

          [/h]         This specifies to indicate the program to display all
                       the possible syntax only.

      The default syntax is:

                EN1100CS /IRQ:5 /IOP:300


[3]  SOCKET and CARD SERVICES INSTALLATION ADVISORY


     For those who installed EMM386.EXE in your config.sys, please exclude
     memory address D400-D7FF from your system. PCMCIA Ethernet card enabler
     program will use this space to read Ethernet ID and CIS from on-board
     flash memory.
     [Example]
               DEVICE=EMM386.EXE NOEMS X=D400-D7FF
                               or
               DEVICE=EMM386.EXE NOEMS X=D000-DFFF

     For those who installed Card and Socket Services device driver in your
     config.sys, please run EN1100CS.EXE (see ENABLE PCMCIA CARD) after those 
     device drivers. The default configuration is IRQ=3, IO=300.

     [Phoenix PCM+ V3.0]
       DEVICE=C:\PCM3\CNFIGNAM.EXE /SETUP-DEFAULTS
       DEVICE=C:\PCM3\PCMSS.EXE
       DEVICE=C:\PCM3\PCMCS.EXE
       DEVICE=C:\PCM3\PCMRMAN.SYS
       DEVICE=C:\PCM3\PCMSCD.EXE
       DEVICE=EN1100CS.EXE

     [SystemSoft CardSoft V3.1]
       DEVICE=C:\CARDSOFT\SS365SL.EXE  //Socket Service for Intel Compatible //
       DEVICE=C:\CARDSOFT\CS.EXE
       DEVICE=C:\CARDSOFT\CSALLOC.EXE
       DEVICE=EN1100CS.EXE

     [Award Cardware V2.0]
       DEVICE=C:\CARDWARE\SSPCIC.EXE
       DEVICE=C:\CARDWARE\PCCS.EXE
       DEVICE=C:\CARDWARE\PCRM.EXE /AUTODETECT
       DEVICE=EN1100CS.EXE
             [Note] Please do not use PCENABLE.EXE

     [AMI AMICARDZ]
       DEVICE=C:\AMI\SSSL.SYS
       DEVICE=C:\AMI\AMICS.SYS
       DEVICE=EN1100CS.EXE
             [Note] Please do not use PCBE.SYS

     [Databook CardTalk V3.02]
       DEVICE=C:\CARDTALK\TMB250.SYS /io:240
       DEVICE=C:\CARDTALK\CTALKCS.EXE
       DEVICE=C:\CARDTALK\CARDTALK.EXE /A /IOW=300-31F /MEMW=D000-D7FF
       DEVICE=EN1100CS.EXE

     [IBM Thinkpad Socket and Card Services V2.12]
       DEVICE=C\EMM386.EXE NOEMS I=B000-B7FF X=C800-CFFF X=D000-DFFF
       DEVICE=C:\THINKPAD\IBMDSS01.SYS /D
       DEVICE=C:\THINKPAD\IBMDOSCS.SYS
       DEVICE=C:\THINKPAD\DICRMU01.SYS /MA=C800-DFFF
       DEVICE=C:\THINKPAD\$ICPMDOS.SYS
       DEVICE=EN1100CS.EXE


[4]  Netware DOS ODI Driver


     This directory contains Ethernet DOS ODI driver EN1100.COM that
     supports NetWare 3.x, 4.x and 5.x, NetWare Lite and other ODI interface
     application.

            EN1100.COM : DOS/ODI Driver for NetWare 3.x, 4.x and 5.x.


     The following instructions let you to install Novel NetWare DOS ODI
     Driver :

     How To Install
     ---------------
       You need following five files to install DOS ODI DRIVER.

          a. LSL.COM           ---- supported by Novell
          b. EN1100.COM        ---- Novell DOS ODI Driver, supported
                                    by manufacturer
          c. IPXODI.COM        ---- supported by Novell
          d. NETX.EXE          ---- supported by Novell
                  or
             VLM.EXE

          e. NET.CFG           ---- optional, configuration file

       After boot your workstation, type following comments on the console:

               LSL             <Enter>
               EN1100          <Enter>
               IPXODI          <Enter>
               NETX            <Enter>

       then, you can log in to the file server.

       Normally,  you will need a NET.CFG file to configure your Ethernet
       PCMCIA card.
         You  can  see  Netware 386  Installation  appendix E for more
       information about NET.CFG.

       Below is a sample NET.CFG file:

               LINK DRIVER EN1100
                   port 300
                   int  5
                   Frame Ethernet_II
                   Frame Ethernet_802.3
                   Protocol IPX E0 Ethernet_802.2
                   ; NWAY   ;Auto Negotiation, default is enabled
                   ; S10    ;10BaseT Half Duplex Mode
                   ; S10FD  ;10BaseT Full Duplex Mode
                   ; S100   ;100BaseTX Half Duplex Mode
                   ; S100FD ;100BaseTX Full Duplex Mode
                      :
                      :


[5]  Packet Driver


     The driver EN1100.COM can be used for Ethernet PCMCIA adapter.

     To load the packet driver, type EN1100 0x60.

     EN1100 syntax:

     EN1100 [options] <packet_int_no> <int_level> <io_addr>

     where:

     [options]

       -i -- Force driver to report itself as IEEE 802.3 instead of Ethernet II.
       -d -- Delayed initialization.  Used for diskless booting
       -n -- NetWare conversion.  Converts 802.3 packets into 8137 packets
       -w -- Windows hack, obsoleted by winpkt
       -p -- Promiscuous mode disable
       -a -- Auto-Negotiation Mode
       -1 -- Line Speed 10M, Half Duplex Mode
       -2 -- Line Speed 10M, Full Duplex Mode
       -3 -- Line Speed 100M, Half Duplex Mode
       -4 -- Line Speed 100M, Full Duplex Mode
       -u -- Uninstall


     <packet_int_no>    This specifies the software interrupt (IRQ) where
                        you'll load the packet driver. It must be in the range
                        0x60 to 0x80.

     <int_level>        This specifies the hardware interrupt (IRQ) where your
                        card will be indicated.

     <io_addr>          This specifies the I/O address .


     Example:

        The following command line loads the Ethernet Packet Driver
        at software interrupt 60h, at I/O address 300, at hardware interrupt 5.

                 EN1100 0x60 0x5 0x300
                          or
                 EN1100 0x60

        Note: The default I/O address is 300 .
        Note: The default hardware interrupt is 5.
        Note: The placement of 0x prior to the parameters.


[6]  NDIS Driver for Windows 95


     INSTALLATION PROCEDURE:

     1) Insert the PCMCIA Adapter into the PCMCIA slot.  The system displays
        the "New Hardware Found" window, with "PCMCIA-10/100Mbps Ethernet PC Card" as
        the device name.

     2) Select "Drivers from disk provided by hardware manufacturer".

     3) At the "Install From Disk" window, enter the drive letter and path
        where the device information file (.INF file) and device driver can be
        found (e.g.  A:\WIN95).  Press "OK".  The driver then installs itself.

     4) Occasionally, the system may ask for files from the Windows
        distribution disks.  Follow the prompt until the installation is
        complete.

     5) Reboot the machine to start the network.


[7]  NDIS Driver for Windows 98


     INSTALLATION PROCEDURE:

     1) Insert the PCMCIA Adapter into the PCMCIA slot.  The system displays
        the "New Hardware Found" window, with "PCMCIA-10/100Mbps Ethernet PC Card" as
        the device name.

     2) Insert the driver diskette into your floppy drive, and specify the
        path of the driver in the diskette(i.e. A:\WIN98) to copy the driver
        files to your system.


     3) When the driver installation is completed, restart WIN98.

[8]  NDIS Driver for Windows ME


     INSTALLATION PROCEDURE:

     1) Insert the PCMCIA Adapter into the PCMCIA slot.  The system displays
        the "New Hardware Found" window, with "PCMCIA-10/100Mbps Ethernet PC Card" as
        the device name.

     2) Insert the driver diskette into your floppy drive, and specify the
        path of the driver in the diskette(i.e. A:\WINME) to copy the driver
        files to your system.

[9] NDIS DRIVER FOR WINDOWS NT 3.51


     INSTALLATION PROCEDURE:

     1) Open the Control Panel, and choose Network Settings.

     2) Click the Add Adapter button.

     3) Select <Other> Requires disk from manufacturer.

     4) Type in the path A:\NT351

     5) Select the "PCMCIA 10/100Mbps Fast Ethernet PC Card".

     6) Set the IRQ level and I/O Port Address to any free resources.

     7) Select Connection Type.

     8) Click on OK and back to the Network Settings.

     9) Click on "Bindings" button.

    10) Click on OK and Restart the Machine.


[10] NDIS DRIVER FOR WINDOWS NT 4.0


     INSTALLATION PROCEDURE:

     1) Double-click on the "My Computer" icon.
        Then, double-click on the "Control Panel" icon.

     2) In the "Control Panel" window,
        double-click on the "Network" icon.

     3) In the "Network" window,
        click on the "Adapter".

     4) Click on the [Add] button.
        A list of all available drivers will be displayed.

     5) Click on the [Have Disk...] button, for third-party adapters not
        included in the list.


     6) Insert the PCMCIA 10/100Mbps Fast Ethernet PC Card Installation Diskette in
        floppy disk drive, and type the path for the driver.

        Example:
                A:\NT40

        Then click on the [OK] button.

        Windows NT 4.0 will attempt to locate the OEMSETUP.INF file
        in the specified path. If it exists there, Windows NT will then
        copy the appropriate drivers to the Windows NT system.

     7) In the "Select OEM Option" window, select "PCMCIA 10/100Mbps Fast Ethernet PC Card"
        item, then click on the [OK] button.

     8) Set the IRQ level and I/O Port Address to any free resources.

     9) Select Connection Type.

    10) Till now, the PCMCIA 10/100Mbps Fats Ethernet PC Card driver are now installed.

        The installation procedure will then proceed to the next steps.
        Please refer to your Windows NT installation guide for information
        on these steps.

[11]  NDIS Driver for Windows 2000


     INSTALLATION PROCEDURE:

     1) Insert the PCMCIA Adapter into the PCMCIA slot.  The system displays
        the "New Hardware Found" window, with "PCMCIA-10/100Mbps Ethernet Card" as
        the device name.

     2) Insert the driver diskette into your floppy drive, and specify the
        path of the driver in the diskette(i.e. A:\WIN2000) to copy the driver
        files to your system.


[12]  NDIS Driver for Windows XP


     INSTALLATION PROCEDURE:

     1) Insert the PCMCIA Adapter into the PCMCIA slot.  The system displays
        the "New Hardware Found" window, with "PCMCIA-10/100Mbps Ethernet PC Card" as
        the device name.

     2) Insert the driver diskette into your floppy drive, and specify the
        path of the driver in the diskette(i.e. A:\WINXP) to copy the driver
        files to your system.

Download Driver Pack

How To Update Drivers Manually

After your driver has been downloaded, follow these simple steps to install it.

  • Expand the archive file (if the download file is in zip or rar format).

  • If the expanded file has an .exe extension, double click it and follow the installation instructions.

  • Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.

  • Find the device and model you want to update in the device list.

  • Double-click on it to open the Properties dialog box.

  • From the Properties dialog box, select the Driver tab.

  • Click the Update Driver button, then follow the instructions.

Very important: You must reboot your system to ensure that any driver updates have taken effect.

For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.

server: web4, load: 2.02