1. necsvga.zip Driver
2. readme.txt File Contents

readme.txt Driver File Contents (necsvga.zip)

***NEC SVGA JC1431VMA MONITOR***
***INSTALLATION INSTRUCTIONS***
***VERSION 1.21 (9/10/2004)***

BY FENDER BENDER SOFTWARE

NOTE:MAXIMIZE THIS WINDOW IF USING NOTEPAD AND .25" MARGINS
ON THE LEFT AND RIGHT MARGINS
---------------------------------------------------------------------------
TABLE OF CONTENTS
1. SYSTEM REQUIREMENTS
2. INCLUDED FILES
3. INSTALLATION INSTRUCTIONS (RECOMMENDED METHOD)
4. INSTALLATION INSTRUCTIONS (SECONDARY METHOD)-USE ONLY FOR WINDOWS 95
	OR 98	
5. DRIVER PROBLEMS
6. CONTACT INFORMATION


1. SYSTEM REQUIRMENTS
        80486SX @ 25MHz
        MICROSOFT WINDOWS 95 OR HIGHER
        NEC SVGA JC1431VMA MONITOR

2. INCLUDED FILES
        NECSVGA09102004.INF
        README.TXT

3. INSTALLATION INSTURCTIONS (RECOMMENDED METHOD)
        A. GOTO THE CONTROL PANEL
        B. OPEN YOUR DISPLAY PROPERTIES
        C. CLICK ON THE "SETTINGS" TAB
        D. CLICK ON THE ADVANCED SETTINGS BUTTON
	E. SELECT THE "MONITORS" TAB
	F. PRESS THE CHANGE BUTTON
	G. WHEN SELECTING MONITORS, PRESS THE HAVE DISK BUTTON
	H. TYPE IN THE DIRECTORY WHERE THE FILE "NECSVGA.INF" IS 
	LOCATED
	I. WHEN THE MONITOR "NEC SVGA JC1431VMA [9-10-2004]" COMES UP,
	PRESS OK.
	J. VERIFY YOUR INSTALLATION BY SELECTING THE DISPLAY RESOLUTION
	"800x600 HIGH COLOR (16 BIT)"  IF IT DISPLAYS PROPERLY, THE
	DRIVER TOOK EFFECT AND YOU ARE READY TO GO.  OTHERWISE PROCEED
	TO THE SECONDARY INSTALLATION METHOD.
NOTE 1:YOU MIGHT HAVE TO ADJUST YOUR REFRESH RATES IN ORDER TO GET THE
PROPER RESULTS

NOTE 2:THE DISPLAY SETTING "640X480" DOES NOT REQUIRE THIS DRIVER TO
WORK

NOTE 3:800x600 PIXELS WILL NOT WORK ON ALL REFRESH RATES ON ALL
COMPUTERS.

TIP: START YOUR REFRESH RATE AT 60HZ.  IF THIS DOESNT WORK, KEEP
TRYING DIFFERENT REFRESH RATES.  IF YOUR SCREEN GOES BLANK, DON'T
TOUCH ANYTHING FOR 30 SECONDS.  IT WILL GO BACK TO THE LAST SETTING.
KEEP DOING THIS UNTIL YOU FIND A SETTING THAT WORKS PROPERLY.


4. INSTALLATION INSTRUCTIONS (SECONDARY METHOD) 
***ONLY USE FOR WINDOWS 95/98***

        A. GOTO THE CONTROL PANEL
        B. OPEN YOUR DISPLAY PROPERTIES
        C. CLICK ON THE "SETTINGS" TAB
        D. CLICK ON THE ADVANCED SETTINGS BUTTON
	E. SELECT THE "MONITORS" TAB
	F. PRESS THE CHANGE BUTTON
	G. WHEN SELECTING MONITORS, LOOK UNDER STANDARD MONITOR TYPES
	H. LOOK FOR THE "SUPER VGA 1024X768" MONITOR.
	I. WHEN YOU HAVE THIS OPTION HIGHLIGHTED PRESS OK.
	J. REPEAT STEPS A-F
	K. WHEN SELECTING MONITORS, PRESS THE HAVE DISK BUTTON
	L. TYPE IN THE DIRECTORY WHERE THE FILE "NECSVGA90.INF" IS 
	LOCATED
	M. WHEN THE MONITOR "NEC SVGA JC1431VMA [9-10-2004]" COMES UP,
	PRESS OK.
	N. VERIFY YOUR INSTALLATION BY SELECTING THE DISPLAY RESOLUTION
	"800x600 HIGH COLOR (16 BIT)"  IF IT DISPLAYS PROPERLY, THE
	DRIVER TOOK EFFECT AND YOU ARE READY TO GO.  IF THIS DID NOT
	WORK, THIS DRIVER MAY BE INCOMPATIBLE WITH YOUR COMPUTER.  
	PLEASE READ THE SECTION "DRIVER PROBLEMS" TO SEE IF YOUR MODEL
	COMPUTER IS MENTIONED.
NOTE 1:YOU MIGHT HAVE TO ADJUST YOUR REFRESH RATES IN ORDER TO GET THE
PROPER RESULTS

NOTE 2:THE DISPLAY SETTING "640x480" DOES NOT REQUIRE THIS DRIVER TO
WORK

NOTE 3:800x600 PIXELS WILL NOT WORK ON ALL REFRESH RATES ON ALL
COMPUTERS.

TIP: START YOUR REFRESH RATE AT 60HZ.  IF THIS DOESNT WORK, KEEP
TRYING DIFFERENT REFRESH RATES.  IF YOUR SCREEN GOES BLANK, DON'T
TOUCH ANYTHING FOR 30 SECONDS.  IT WILL GO BACK TO THE LAST SETTING.
KEEP DOING THIS UNTIL YOU FIND A SETTING THAT WORKS PROPERLY.


5. DRIVER PROBLEMS/CONFLICTS
	
THIS DRIVER WILL NOT WORK OR CONFLICT WITH THE FOLLOWING COMPUTERS 
OR DISPLAY CARDS:

	1. COMPAQ PROLINEA 4/xx
	THESE COMPUTERS HAVE THE DISPLAY CARD "TSENG ET4000 W/32,"
	WHICH DOES NOT ALLOW THE USER TO ADJUST THE REFRESH RATES.
	THE FOLLOWING DISPLAY RATES WILL NOT WORK WITH THIS MONITOR
	ON THE TSENG ET4000 W/32 DISPLAY CARD:
	
	1024X768-256 COLORS
	800X600-HIGH COLOR (16 BIT)
	800X600-TRUE COLOR (24 BIT)
	
	ALL OTHER DISPLAY RESOLUTIONS WILL WORK.

THIS DRIVER MAY CONFLICT WITH THE FOLLOWING OPERATING SYSTEMS:

	1. MICROSOFT WINDOWS 95 
	WINDOWS 95 MIGHT HAVE A HARDER TIME ACCEPTING THIS DRIVER
	DUE TO THE LACK OF STANDARD MONITOR TYPES @ 75 Hz.  SOME
	COMPUTERS MIGHT NOT COPY THIS FILE TO YOUR INF DIRECTORY.  
	THE ONLY WAY TO FIND OUT IS TO TRY THE DRIVER

	2. MICROSOFT WINDOWS XP HOME/PROFESSIONAL
	WINDOWS XP MIGHT SAY THE DRIVER IS NOT DIGITALLY SIGNED.  JUST
	IGNORE THIS AND PRESS "CONTINUE ANYWAY".

6. CONTACT INFORMATION

IF YOU FIND A PROBLEM OR WANT TO CONTACT ME, E-MAIL ME AT:
PRODUCTBUYERS@YAHOO.COM