README.TXT Driver File Contents (100pac.zip)

           TRENDware TE-PCI/TE-100PCI Ethernet Adapter Installation
                         for UnixWare 2.01

 Contents
 ÄÄÄÄÄÄÄÄ
     Introduction
     Requirements
     Minimum Skill Level
     Getting Started

 Introduction
 ÄÄÄÄÄÄÄÄÄÄÄÄ
    This installation assumes that the adapter is working properly.
    Getting Started will describe the installation instructions.

 Requirements
 ÄÄÄÄÄÄÄÄÄÄÄÄ
     A PCI compatible computer
     Novell/SCO UnixWare 2.x
     A PCI Family Series Adapter
     A knowledge of basic Unixware commands and editing text files

 Minimum Skill Level
 ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
   A knowledge of basic UnixWare commands
   A knowledge of editing text files
   A knowledge of UnixWare basic file structure
   A knowledge of the network driver configuration being used

 Getting Started
 ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ

   login UNIX as "root"
    login: root
    Password: XXXXXX

   #doscp a:/unixware/setup setup_tepci
    #chmod +x setup_tepci
    #./setup_tepci  a:/unixware (you can specify another path as you wish)

   Install the Driver
    #cd /usr/lib/tcprt/eth
    #chmod +x build_tepci
    #./build_tepci

    Do you wish to install or delete the network driver(i/d/q)?     i
                                                                    ~
/* first adapter install */
    Do you want to configure Board_0? (y/n/q)                       y
                                                                    ~
    Board_0 configuring ...

    Please enter the IP host name for the device tepci_0 (default:xxxx): aaron
                                                                         ~~~~~
    Please Initialize the IP Address for host XXXX (default: xxx.xxx.xxx.xxx):
    192.9.200.1
    ~~~~~~~~~~~

    Configure host XXXX with default Ethernet(TM) ifconfig option?
    Info message is long. (yse no ClassC BerkeleyC info; default: info): y
                                                                         ~

/* the following let you configure NICs */

/* If you are configuring board 0 then the following messages will prompt */
/* for specifying the access type of PCI bus */
    Note:
      The default is to use the PCI BIOS calls (in 32-bit protected mode).
      Some systems may not support these calls, in which case there will be
      problems at boot time. If using a system that does not support 32-bit
      protected mode PCI BIOS calls, direct hardware accesses must be used.
      PCI mechanism 1 or PCI mechanism 2 should be selected depending on
      your machine support."


      Please specify the way used by PCI to access hardware.........

      0. Use 32-bit protected mode PCI BIOS calls."
      1. Direct access to the HW, using PCI mechanism 1."
      2. Direct access to the HW, using PCI mechanism 2."

      Enter number of PCI access type selection (0 1 2) [0] or 'q' to quit: 1
                                                                            ~
      PCI access type : Direct access to the HW, using PCI mechanism 1.

      Please choose the line speed that you want............

      0. Use default value.
      1. 10 MB/sec mode.
      2. 100 MB/sec mode.
      3. Automatic detection between 10 MB/sec and 100 MB/sec mode.

      Enter number of line speed selection (0 1 2 3) [0] or 'q' to quit: 3
                                                                         ~

      Line Speed : AUTOSENSE_MODE

      Please choose the media mode that you want............

      0. Use default value.
      1. Point to point full duplex twisted pair connection.
      2. BNC connection.
      3. Twisted pair connection.
      4. Automatic detection between TP BNC.
      5. Twisted pair connection with linkfail test ignore & set polarity plus.

      Enter number of media mode selection (0 1 2 3 4 5) [0] or 'q' to quit: 4
                                                                             ~

      Media Mode : AUTOSENSE_MODE

/* second adapter install */
      Do you want to configure Board_1? (y/n/q)                       y
                                                                      ~
/* the prompts listed above will be repeated */

/* the third adapter */
      Repeat the above steps ....

      0: tepci_0 adapter 0
      1: tepci_1 adapter 1
      2: tepci_2 adapter 2
      3: tepci_3 adapter 3
Select one adapter to support Netware: 0
                                       ~
      Do you wish to relink the kernel now ? y
                                             ~

Note1: The IRQ number must match with the value set in ROM-BIOS before you
       specify this value, please check it.
       The IRQ for PCI bus can be accessed by pressing [DEL] key when system
       is power on and choose the proper select item to set IRQ for PCI bus.

       Example: ROM PCI/ISA BIOS (2A4X5C31)
                PCI/GREEN FUNCTION SETUP
                AWARD SOFTWARE, INC.

       Press [DEL] key  -->  PCI/GREEN FUNCTION SETUP

                             Slot 3 Using INT# : A-PIRQ1
                                           .
                                           .
                                           .
                             PIRQ1# Connect IRQ: 5 By Single
                                                 ~

Note2: After you install device driver, you can create a DeskTop user that
       has 'root' privilege and using the following steps:

       Admin_Tools -> Networking
                   -> NetWare_Setup
                   -> LAN options
                   -> IPX LAN Device
                      IPX LAN Frame Type

       IPX LAN Device       Specifying the device driver for the network
                            board.

       IPX LAN Frame Type   Specifying the frame type.



Download Driver Pack

How To Update Drivers Manually

After your driver has been downloaded, follow these simple steps to install it.

  • Expand the archive file (if the download file is in zip or rar format).

  • If the expanded file has an .exe extension, double click it and follow the installation instructions.

  • Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.

  • Find the device and model you want to update in the device list.

  • Double-click on it to open the Properties dialog box.

  • From the Properties dialog box, select the Driver tab.

  • Click the Update Driver button, then follow the instructions.

Very important: You must reboot your system to ensure that any driver updates have taken effect.

For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.

server: ftp, load: 1.56