Accton Technology Corporation EN2216/2316 PCMCIA Ethernet Adapter NetWare Server Driver Installation Contents: 1. Files Description 2. Enable the EN2216/2316 PCMCIA Adapter 3. Driver Installation for NetWare Server 3.1x 4. Driver Installation for NetWare Server 4.x 5. Optional Parameters for ACCPCM.LAN 1. Files Description ------------------------------------------------------------- Filename Description ------------------------------------------------------------- README.TXT This file. Presents a summary for NetWare Server driver installation. ACCPCM.LAN 32-Bit ODI Server driver. ACCPCM.LDI Driver installation information file. ETHERTSM.NLM NetWare Server 3.1X, 4.X LAN driver Topology Specific Module (TSM) for Ethernet. 3.1X\NBI31X.NLM NetWare Server 3.1X Bus Interface module. 3.1X\MSM31X.NLM NetWare Server 3.1X LAN driver Media Support Module (MSM). 4.X\MSM.NLM NetWare Server 4.X LAN driver Media Support Module (MSM). ------------------------------------------------------------------ 2. Enable the EN2216/2316 PCMCIA Adapter ACCOPEN.EXE is the EN2216/2316 enabling program. You have to run ACCOPEN.EXE under DOS to enable EN2216/2316 before bringing up the Netware Server. The EN2216/2316 server driver will not work if the adapter is not enabled first in DOS. The syntax for ACCOPEN is: ACCOPEN [/INT:x][/PORT:xxx] * INT - interrupt (IRQ) number to be used by the adapter. This number must not be in use by any other device in the system. * PORT- Starting I/O port address in HEX format. The adapter requires 32 consecutive free I/O port addresses. The default value for INT is 5. The default value for PORT is 0x300. Example: The following command enables EN2216/2316 with IRQ 3 and I/O port address 300: ACCOPEN /INT:3 /PORT:300 3. Driver Installation for NetWare Server 3.1x 1. Insert EN2216/2316 Driver Disk in the floppy drive (e.g. A:). 2. Copy the following file from the Driver Disk to the root directory on the hard disk: \NETWARE\SERVER\ACCOPEN.EXE Exeute ACCOPEN to enable the adapter as described in Section 2 above. 3. Change to the NetWare Server directory (for example: CD \SERVER.312) 4. Copy the following files from the Driver Disk to the NetWare Server directory on the hard disk: \NETWARE\SERVER\3.1X\NBI31X.NLM \NETWARE\SERVER\3.1X\MSM31X.NLM \NETWARE\SERVER\ETHERTSM.NLM \NETWARE\SERVER\ACCPCM.LAN -------------------------------------------------------------------------- Sample AUTOEXEC.NCF for NetWare Server 3.12 LOAD C:NBI31X LOAD C:MSM31X LOAD C:ETHERTSM LOAD C:ACCPCM FRAME=ETHERNET_802.2 NAME=E_8022 LOAD C:ACCPCM FRAME=ETHERNET_802.3 NAME=E_8023 LOAD C:ACCPCM FRAME=ETHERNET_II NAME=E_II LOAD C:ACCPCM FRAME=ETHERNET_SNAP NAME=E_SNAP BIND IPX E_8022 NET=10 BIND IPX E_8023 NET=20 BIND IPX E_II NET=30 BIND IPX E_SNAP NET=40 -------------------------------------------------------------------------- 4. Driver Installation for NetWare Server 4.X 1. Copy the following files from the Driver Disk to the NetWare Server directory on the hard disk. \NETWARE\SERVER\4.X\MSM.NLM \NETWARE\SERVER\ETHERTSM.NLM \NETWARE\SERVER\ACCPCM.LAN Copy the following file from the Driver Disk to the root directory on the hard disk: \NETWARE\SERVER\ACCOPEN.EXE Exeute ACCOPEN to enable the adapter as described in Section 2 above. 2. Change to NetWare Server directory (for example: CD \NWSERVER). 3. Load the NetWare Server System by typing SERVER, and press <Enter>. 4. When the Server prompt appears, load the NetWare Server Installation Utility by entering the following command on the server console: LOAD INSTALL 5. Select "Driver options" from the "Installtion Options" menu, and press <Enter>. 6. Select "Configure network drivers" from the "Driver Options" menu, and press <Enter>. 7. Select "Select a driver" from the "Additional Driver Actions" menu, and press <Enter>. 8. Press <Ins> to install an unlisted driver, and press <F3> to specify a different path. 9. Insert the EN2216/2316 Driver Disk in the floppy drive (e.g. A:), and specify the directory on the disk where the drivers are located (e.g. A:\NETWARE\SERVER). 10. Select "Accton EN2216/2316 PCMCIA Adapter" from the "Select a driver to install:" menu, and press <Enter>. 11. If necessary, select "Select/Modify driver parameters and protocols" from the "Board Accton EN2216/2316 (Driver ACCPCM) Actions" menu, and press <Enter> to set up the driver parameters. After the driver parameters are set, select "Save parameters and load driver", and press <Enter>. 12. Follow instructions to complete driver installation. 13. Bring down the server by entering "down", and then "exit." This brings the system back to the MS-DOS prompt. 14. Bring up the server by entering "server" on the MS-DOS command prompt. After the server comes up, the adapter and the network should be working. 15. Please beware that each time you reboot the system, you have to run ACCOPEN.EXE to enable EN2216/2316 as described in section 2 above. -------------------------------------------------------------------------- Sample AUTOEXEC.NCF for NetWare Server 4.X LOAD C:NBI LOAD C:MSM LOAD C:ETHERTSM LOAD C:ACCPCM FRAME=ETHERNET_802.2 NAME=E_8022 LOAD C:ACCPCM FRAME=ETHERNET_802.3 NAME=E_8023 LOAD C:ACCPCM FRAME=ETHERNET_II NAME=E_II LOAD C:ACCPCM FRAME=ETHERNET_SNAP NAME=E_SNAP BIND IPX E_8022 NET=10 BIND IPX E_8023 NET=20 BIND IPX E_II NET=30 BIND IPX E_SNAP NET=40 -------------------------------------------------------------------------- 5. Optional Parameters for ACCPCM.LAN The following are the optional parameters for ACCPCM.LAN: 1. FRAME: Specifies which frame type is used by the driver. Accepted values are Ethernet_802.2, Ethernet_802.3, Ethernet_II and Ethernet_SNAP. Multiple frame types can be enabled by loading the same driver with different FRAME types. Examples: LOAD ACCPCM FRAME=ETHERNET_802.2 LOAD ACCPCM FRAME=ETHERNET_802.3 LOAD ACCPCM FRAME=ETHERNET_II LOAD ACCPCM FRAME=ETHERNET_SNAP 2. INT: The Interrupt (IRQ) value to be used by the adapter. You have to pay attention that the INT value you specified here must match the /INT value you specified for ACCOPEN, the EN2216/2316 DOS enabling program. Please refer to section 2 on how to use ACCOPEN to enable the adapter in DOS before bringing up the server. Example: LOAD ACCPCM INT=3 FRAME=ETHERNET_802.2 3. PORT: The starting I/O port address. You have to pay attention that the PORT value you specified here must match the /PORT value you specified for ACCOPEN, the EN2216/2316 DOS enabling program. Please refer to section 2 on how to use ACCOPEN to enable the adapter in DOS before bringing up the server. Example: LOAD ACCPCM INT=3 PORT=300 FRAME=ETHERNET_802.2Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.