1. EN166x.zip Driver
2. README.TXT File Contents

README.TXT Driver File Contents (EN166x.zip)

                  Accton Technology Corporation
                  SOFTWARE INSTALLATION INSTRUCTIONS
         FOR MICROSOFT LAN MANAGER DOS CLIENT NDIS 2.01 DRIVER


 The driver \MSLANMAN.DOS\DRIVERS\ETHERNET\Accton\ETHNE.DOS conforms
 to the Network Driver Interface Specification (NDIS) defined by
 Microsoft and 3Com.



 =============================
 DRIVER INSTALLATION PROCEDURE
 =============================

 Use one of the following procedures to match your LAN Manager version,
 either 2.0, 2.1, or 2.2.  Then refer to the sample configuration file
 (following all three procedures) that also corresponds to your version;
 some circumstances require you to change settings in those files.

 LAN Manager version 2.0
 -----------------------

 1. Connect to the LAN Manager directory and enter the Setup utility.

 2. Select "Import Network Drivers..." in the Action field.
    Press [ENTER] to continue.

 3. Insert the Support Disk for Accton EN166X into the floppy drive.
    Press [ENTER] to see the list of Imported Network Drivers.

 4. Select the Accton EN166X Ethernet Adapter driver, using the [SPACEBAR].
    Press [ENTER] to confirm.

 5. Follow the prompts displayed to complete the process,
    until "Network Driver" is displayed.

 6. Identify your network adapter if asked.  For example, select
    "Accton EN166X Ethernet Card" for the Accton EN166X ISA adapter.

 7. Select the "Add driver" and the "Add protocol" options.
    Select "OK" to confirm.  The computer's primary parameters should
    display.

 8. Follow the prompts displayed to complete the process.

 9. Save all selections.  Select "Save" in the "Action Menu".

 10. Press [F3] to exit.


 LAN Manager version 2.1
 -----------------------

 1. Connect to the LAN Manager directory and enter the LMSETUP utility.
    The Microsoft LAN Manager Setup screen displays.

 2. Select "Network Drivers..." in the "Configuration" field.
    Press [ENTER] to confirm.

 3. Select "Add New Configs" and press [ENTER] to display a list of
    network adapter drivers.

 4. Select "Other Driver" and press [ENTER].

 5. Insert the Support Disk for Accton EN166X into the floppy drive.
    Enter the path name of the diskette.  Select "OK" to continue.

 6. Select the "Accton EN166X Ethernet Adapter" driver.
    Select "OK" to confirm.

 7. Select an appropriate protocol, using the [SPACEBAR] to highlight it.
    Select "OK" to confirm.

 8. The Configuration Complete message should display.

 9. Save the configuration; select "Save".

 10. Press [F3] to exit.


 LAN Manager version 2.2
 -----------------------

 1. Connect to the LAN Manager directory and enter the Setup utility.
    The Microsoft LAN Manager Setup screen displays.

 2. Select "Network Drivers..." in the "Configuration" field.
    Press [ENTER] to confirm.

 3. Select "Add New Config" and press [ENTER] to display a list of
    network adapter drivers.

 4. Select "Other Driver" and press [ENTER].

 5. Insert the Support Disk for Accton EN166X into the floppy drive.
    Enter the path name of the diskette.  Select "OK" to continue.

 6. Select the "Accton EN166X Ethernet Adapter" driver.
    Select "OK" to confirm.

 7. Select an appropriate protocol, using the [SPACEBAR] to highlight it.
    Select "OK" to confirm.  If you select the TCP/IP protocol, you
    will be prompted for the IP address, the subnet mask, and the
    default gateway (router).  By default, the workstation number of
    the NetBIOS session is set to 6.

    See the Microsoft LAN Manager Installation Manual or see online
    help for more details

 8. The Configuration Complete message should display.

 9. Save the configuration; select "Save".

 10. Press [F3] to exit.


 All LAN Manager versions
 ------------------------

 NOTE: If you are installing LAN Manager for the first time, you will
       be prompted for the default user name and domain of the
       workstation, as well as to answer, and for other Windows
       environment and memory management information.

 You must edit the "[Accton_NIF]" section of the PROTOCOL.INI file in
 the following cases.  See the example at the end of this file.

    IF more than one Accton EN166X ISA adapter is installed, you must
       specify the interrupt (interrupt = ") and I/O base address
       ("iobase = ") for each adapter.  Use the same settings from the
       hardware configuration of each adapter; you can view the
       settings in SETUP166.

       NOTE: The ISA Plug-and-Play HW configuration of an additional
             adapter can change the configuration of an existing,
             working adapter.  Check its HW configuration again, and
             if changed, reinstall the driver.

    IF you have a non-Plug-and-Play computer, you must change the
       interrupt setting (interrupt = ") and I/O base address setting
       ("iobase = ") to match the hardware configuration for the
       adapter, as listed by SETUP166.  If you did not make a note
       of them when configured, now use the "View Configuration" menu
       item in SETUP166 to note them.



 ==========================
 SAMPLE CONFIGURATION FILES
 ==========================

 Use one of the following to match your LAN Manager version,
 either 2.0, 2.1, or 2.2.


 LAN Manager version 2.0
 -----------------------

 AUTOEXEC.BAT file:

    @echo off
    PROMPT $P$G
    PATH=c:\PE2;C:\DOS50;C:\NC;
    APPEND=C:\PE2;C:\DOS50;
    REM ===== LANMAN 2.0 ==== DO NOT MODIFY BETWEEN THESE LINES
    REM ===== LANMAN 2.0 ====
    SET PATH=C:\LANMAN.DOS\NETPROG;%PATH%
    C:\LANMAN.DOS\DRIVERS\PROTMAN\NETBIND
    NET START WORKSTATION
    REM ===== LANMAN 2.0 === DO NOT MODIFY BETWEEN THESE LINES
    REM ===== LANMAN 2.0 ====

 CONFIG.SYS file:

    LASTDRIVE=Z
    BUFFERS = 35
    FILES = 35
    ...
    DEVICE=C:\LANMAN.DOS\DRIVERS\PROTMAN\PROTMAN.DOS /i:C:\LANMAN.DOS
    DEVICE=C:\LANMAN.DOS\DRIVERS\ETHERNET\Accton\ETHNE.DOS
    DEVICE=C:\LANMAN.DOS\DRIVERS\PROTOCOL\NETBEUI\NETBEUI.DOS

 PROTOCOL.INI file:

    [PROTOCOL MANAGER]
    DRIVERNAME = PROTMAN$

    [NETBEUI_XIF]
    Drivername = netbeui$
    BINDINGS = "Accton_NIF"

    [Accton_NIF]
    ; PROTOCOL.INI for Accton EN166X ethernet adapter
    drivername = ETHNE$
    ; interrupt = 3                  (See above note for "All LAN Manager
    ; iobase = 0x300                  versions" for conditions requiring
    ; End of this sample file         you to change these lines!)


 LAN Manager version 2.1 or 2.2
-------------------------------

 AUTOEXEC.BAT file:

    @echo off
    PROMPT $P$G
    PATH=c:\PE2;C:\DOS50;C:\NC;
    APPEND=C:\PE2;C:\DOS50;
    @REM === LANMAN 2.1 === DO NOT MODIFY BETWEEN THESE LINES
    @REM === LANMAN 2.1 ===
    SET PATH=C:\LANMAN.DOS\NETPROG;%PATH%
    NET START WORKSTATION
    LOAD NETBEUI
    @REM === LANMAN 2.1 === DO NOT MODIFY BETWEEN THESE LINES
    @REM === LANMAN 2.1 ===

 CONFIG.SYS file:

    LASTDRIVE=Z
    BUFFERS = 35
    FILES = 35
    .
    .
    .
    DEVICE=C:\LANMAN.DOS\DRIVERS\PROTMAN\PROTMAN.DOS /i:C:\LANMAN.DOS
    DEVICE=C:\LANMAN.DOS\DRIVERS\ETHERNET\Accton\ETHNE.DOS

 PROTOCOL.INI file:

    [PROTMAN]
    DRIVERNAME = PROTMAN$
    DYNAMIC = YES
    PRIORITY = NETBEUI

    [NETBEUI_XIF]
    Drivername = netbeui$
    SESSIONS = 6
    NCBS = 12
    BINDINGS = "Accton_NIF"
    LANABASE = 0

    [Accton_NIF]
    ; PROTOCOL.INI for Accton EN166X ethernet adapter
    drivername = ETHNE$
    ; interrupt = 3                  (See above note for "All LAN Manager
    ; iobase = 0x300                  versions" for conditions requiring
    ; End of this sample file         you to change these lines!)


-----End of File----