8 Workstation: NetWare OS/2 Requester
NetWare* OS/2* ODI Client Driver Installation Notes
===================================================
Location of driver: \OS2\E100BODI.SYS
Sample configuration files
==========================
CONFIG.SYS
DEVICE=C:\NETWARE\E100BODI.SYS
NET.CFG
LINK DRIVER E100BODI
SLOT n
FRAME ETHERNET_802.3
FRAME ETHERNET_802.2
Introduction
============
To connect an OS/2 workstation to a NetWare* server, you must have the
latest version of the Novell NetWare Requester for OS/2 and the
PRO/100+ adapter OS/2 ODI driver.
These installation instructions assume you're using the INSTALL program
that ships with Novell's OS/2 requester. For more information about OS/2
workstations, see the Novell manual, "NetWare Requester for OS/2."
Note: If you're running IBM OS/2 2.0, 2.1 or Warp, you must have the OS/2
Requester version 2.01 or later.
General Instructions
====================
1 Run Novell's INSTALL utility on the OS/2 requester disk and follow
its instructions. If asked for the name of the network interface
driver, enter E100BODI.SYS.
2 Choose the session support you need. This is based on your
configuration. See the NetWare Requester manual if you need help.
3 Save the configuration.
4 When asked for the path and filename for the driver, insert the
Configuration and Drivers disk into the drive and press Enter.
5 After completing the installation section, choose CONFIGURATION from
the main menu. Then choose THIS WORKSTATION. This allows you to
modify the NET.CFG file. (NET.CFG must reside in the root directory.)
Note: The default frame type for E100BODI.SYS is 802.2. If you're
using the 802.3 frame type, you have to include a FRAME
statement in the NET.CFG file. List the 802.3 FRAME type first
in the NET.CFG file.
Hints and Tips
==============
Verify driver loaded properly
-----------------------------
In the CONFIG.SYS file, add a "fake" device=xxx statement after the
E100BODI.SYS line. The screen stops and you can check for error
messages.
Error message "not getting a connection ID"
-------------------------------------------
This OS/2 error message often appears when there is a frame type
mismatch or cable disconnect.
NET.CFG optional parameters
---------------------------
FORCEDUPLEX:
Note: The PRO/100B T4 adapter does not support full duplex at 100
Mbps. It does at 10 Mbps. The PRO/100+ TX adapter supports
full duplex at 10 and 100 Mbps.
Syntax: FORCEDUPLEX n
Where n=0 auto-negotiate (PRO/100+ TX adapter only)
1 half duplex
2 full duplex
Note: If the adapter is set to half or full duplex, set the SPEED
parameter to either 10 or 100. (see SPEED below)
Duplex modes:
Auto-negotiate: The adapter negotiates with the switch/hub how
to send/receive packets, either full or half duplex. If
unsuccessful at negotiating the duplex, the adapter defaults to
half duplex.
Note: The PRO/100B T4 adapter does not support auto-negotiate.
Full duplex: The adapter sends and receives packets at the
same time. This improves the performance of your adapter. Set
duplex mode to full duplex ONLY if you have a switch that
supports full duplex.
Half duplex: The adapter performs one operation at a time. It
either sends or receives.
Default: auto-negotiation (PRO/100+ TX adapter)
half duplex (PRO/100B T4 adapter)
The PRO/100+ TX adapter has the added ability to "talk" to the
switch/hub and determine at which mode to communicate (either
full or half duplex). This is called auto-negotiation. You must
have an auto-negotiating hub (an Nway switch) to get full
duplex support with the FORCEDUPLEX parameter set to 0 (auto-
negotiation).
Examples:
PRO/100+ TX (100 Mbps full duplex):
FORCEDUPLEX 2 (Sets adapter to full duplex)
SPEED 100 (See SPEED parameter below)
PRO/100+ TX (10 Mbps full duplex):
FORCEDUPLEX 2 (Sets adapter to full duplex)
SPEED 10
PRO/100B T4 (100 Mbps full duplex): Not Supported
PRO/100B T4 (10 Mbps full duplex):
FORCEDUPLEX 2 (Sets adapter to full duplex)
SPEED 10
Note: Use auto-negotiate for full duplex support only when the
adapter is connected to a hub/switch that fully supports
Nway auto negotiation specification.
SLOT: For PCI adapters, SLOT is derived from bus number and device
location as defined by the PCI specification. One way to
determine the slot number is to run setup.exe from DOS.
Syntax: SLOT n (n = 1,2,3,4,...)
SPEED: Specifies the speed the driver uses. If you don't use this
parameter, the driver automatically detects the network speed.
If no cable is attached, the driver defaults to 10 Mbps.
If you don't have a auto-negotiating switch/hub and are
configuring the adapter for full or half duplex support,
specify the speed to either 10 or 100 Mbps using this
parameter.
If you use this parameter, the driver operates at the specified
speed instead of automatically detecting network speed.
Syntax: SPEED n (n = 10 or 100)
Default: none, the adapter automatically senses speed
NOTE: Set the SPEED parameter to either 10 or 100 if you're
setting the FORCEDUPLEX parameter to either 1 or 2 (half or
full).
TXTHRESHOLD: Represents the threshold for transmits from extender SRAM
FIFO (output buffer).
Syntax: TXTHRESHOLD n (n = number of 8 bytes)
For example, 16 represents 16x8 (or 128 bytes). In this case,
the LAN controller transmits after copying 128 bytes from the
host memory to the SRAM FIFO.
Default: dynamic
The maximum number that you can specify is 200 (200x8=1600
bytes).
NODE ADDRESS: Specifies a local administered address (LAA) unique to
each adapter. The node address is a 12-digit hexadecimal
number; the second digit must be one of the following digits:
2, 6, A, E.
Syntax: NODE ADDRESS 02A0C9345678
02 => Locally administered address
00 => Typical Intel address (default)
FRAME: Configures the adapter to process the four valid NetWare
Ethernet frame types.
Syntax: FRAME n
n = Ethernet_802.2
Ethernet_802.3
Ethernet_II
Ethernet_SNAP
Default: Ethernet_802.2
PROTOCOL: Indicates the standard protocol in use.
Syntax: Protocol ipx e0 Ethernet_802.2
Values: e0=Ethernet_802.2
0=Ethernet_802.3
8137=Ethernet_II
8137=Ethernet_SNAP
Detailed example
----------------
LINK DRIVER E100BODI
SPEED 100
THRESHOLD 16
NODE ADDRESS 02xxxxxxxxxx
FRAME ETHERNET_802.2
PROTOCOL IPX E0 ETHERNET_802.2
* Third-party trademarks are the property of their respective owners.
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.