README.TXT Driver File Contents (E200_202.exe)

Microsoft LAN Manager
----------------------

Support is provided for the Microsoft LAN Manager (version 2.x) environment.
The driver should be installed using the Microsoft LAN Manager Setup Utility.

Notes:
1) The hardware for the Microsoft LAN Manager environment can be configured
   to run as an OS/2 server, OS/2 workstation, basic MS-DOS workstation, or an
   enhanced MS-DOS workstation. Please refer to your Microsoft LAN Manager
   documentation as needed.

2) The directory structure provided on the ISA Ethernet Card driver diskette 
   has been setup for automatic OEM installation. Also,more information can be 
   found in Microsoft LAN Manager User's Guide.

Driver Installation Using Microsoft LAN Manager Setup Utility

Follow the steps listed below:

1       Insert the ISA Ethernet Card driver diskette into the floppy drive.

        Note:
        Two information files ("E200ND.NIF" and "PROTOCOL.INI") will be
        used for driver installation. These files are located on the ISA
        Ethernet Card driver diskette.

2       Change into the LAN Manager sub-directory on your hard disk by typing:

                cd C:\LANMAN.DOS

        Then press <Enter>. Next start the Microsoft LAN Manager Setup Utility
        by typing:

                setup

        Then press <Enter>.

3       The following message will be displayed:

                Loading Microsoft LAN Manager configuration ...

4       Hold down the <Alt> key and press "C" to access the "Configuration"
        drop down menu.

5       Use the up/down arrow keys to select "Network Drivers..." and then press
        <Enter>. This will open the "Workstation Configuration" window.

6       If you have an existing (old) OTHERS Ethernet driver installed, use the
        tab key to select "<Remove Config>" and then press <Enter>. This removes
        the existing NDIS driver.

7       Use the tab key to select "<Add New Config>" and then press <Enter>.
        This will open the "Network Adapter Drivers" window.

8       Use the tab key to select "<Other Driver>" and then press <Enter>.

9       Enter the disk drive letter (e.g., "A:") where the ISA Ethernet Card
        driver diskette is located.

        Note:
        No path is required since the ISA Ethernet Card diskette is structured 
        for the Microsoft LAN Manager setup.

        Use the tab key to select "<OK>" and then press <Enter>.

10      Use the up/down arrow keys to select "EthernetCard".
        Next,use the tab key to select "<OK>" and then press <Enter>.

        Note:
        If you have older ISA Ethernet Card drivers installed, you will be 
        asked if you want to "Overwrite?" Use the tab key to select "<Yes>" 
        and then press <Enter>.

        The following message will be displayed:

                Copying drivers, please wait ...

        Wait for the message to go away.

11      Use the up/down arrow keys to select the desired protocol, press the
        spacebar to select, and then use the tab key to select "<OK>". Then
        press <Enter>. You will then be returned to the "Workstation
        Configuration" window.

12      Use the tab key to select "<Save>" and then press <Enter>. The following
        message will be displayed:

                Saving Microsoft LAN Manager Configuration ...

        Wait for the message to go away.

13      Hold down the <Alt> key and press "L" to access the "LAN Manager" drop
        down menu.

14      Use the up/down arrow keys to select "Exit Setup" and then press <Enter>
        . The following message will be displayed:

                LAN Manager Configuration Complete

        "<OK>" will be highlighted. Press <Enter>.

        The installation of the ISA Ethernet Card NDIS 2.01 driver for Microsoft 
        LAN Manager is now complete.

File Examples

During installation, LAN Manager will automatically make modifications to the
"CONFIG.SYS", "AUTOEXEC.BAT", and "PROTOCOL.INI" files. Below are sample files
for an ISA Ethernet Card.

CONFIG.SYS

DEVICE=C:\LANMAN.DOS\DRIVERS\PROTMAN\PROTMAN.DOS /i:C:\LANMAN.DOS
DEVICE=C:\LANMAN.DOS\DRIVERS\ETHERNET\E200ND\E200ND.DOS

AUTOEXEC.BAT

SET PATH=C:\LANMAN.DOS\NETPROG;%PATH%
NET START WORKSTATION
LOAD NETBEUI
NET LOGON bill.gates

PROTOCOL.INI

[PROTMAN]
        DRIVERNAME      = PROTMAN$
        DYNAMIC = YES
        PRIORITY        = NETBEUI

[NETBEUI_XIF]
        Drivername      = netbeui$
        SESSIONS        = 6
        NCBS            = 12
        BINDINGS        = "E200ND_NIF"
        LANABASE        = 0

[E200ND_NIF]
        DriverName      = E200ND$

--------------------------------[ END ]---------------------------------------
Download Driver Pack

How To Update Drivers Manually

After your driver has been downloaded, follow these simple steps to install it.

  • Expand the archive file (if the download file is in zip or rar format).

  • If the expanded file has an .exe extension, double click it and follow the installation instructions.

  • Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.

  • Find the device and model you want to update in the device list.

  • Double-click on it to open the Properties dialog box.

  • From the Properties dialog box, select the Driver tab.

  • Click the Update Driver button, then follow the instructions.

Very important: You must reboot your system to ensure that any driver updates have taken effect.

For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.

server: web2, load: 1.03