Practical PC336 ENET PCMCIA Adapter Last update: February 12, 1996 This file provides general information not available in the user manual. Please read this file before installing the product. Contents: --------- 1. Hardware notes 2. The Practical Wizard system requirements 3. Installing the Practical PC336 ENET Support Driver manually 4. The Practical PC336 ENET Support Driver parameters 5. Location of Win 95 INF file 6. Technical Support 1. Hardware notes ----------------- The Practical PC336 ENET PCMCIA adapter supports "Hot" insertion and removal. Thus, the PCMCIA adapter can be inserted into and/or removed from a PC that is either switched off or switched on. The Practical PC336 ENET PCMCIA adapter has full support for Card Services version 2.10, including automatic resources allocation, Hot Swapping and Plug-and-Play features. If you have a Card and Socket Services software version less than 2.10, please contact your computer or operating system manufacturer to receive an upgrade. 2. The Practical Wizard system requirements ----------------------------------------- We recommend that a disk cache program (SMARTDRV.EXE) and the mouse driver are loaded before running the Wizard to speed up the installation and file copying procedures. Important! Make sure that your CONFIG.SYS file has "FILES=30" line. 30 is the minimum value. Otherwise the Wizard will not be able to copy drivers from the distribution diskette. 3. Installing Practical PC336 ENET Support Driver manually -------------------------------------------------------- IMPORTANT NOTE. THIS SECTION IS FOR EXPERIENCED USERS ONLY! Using the Practical Wizard program you can install and configure the PC336 ENET Support Driver in a much easier and safer way. This and the following sections describe manual installation and the command line parameters of the Practical PC336 ENET Support driver. In order to work with the Practical PC336 ENET PCMCIA adapter, you need to install the PC336 ENET Support Driver. Add the following line to your CONFIG.SYS file (after the Card Services drivers, if any): DEVICE = path\PPDRV.EXE [parameters] The Practical PC336 ENET Support Driver may also be loaded from the DOS command prompt or from a batch file: path\PPDRV.EXE [parameters] Without command line parameters, the driver uses default or auto-configured settings. To customize the driver's settings, use the following syntax: PPDRV [/irq=x] [/intm=x] [/inte=x] [/mem=x] [/iom=x] [/ioe=x] [socket=x] [type=x] [/base=x] [/fast=x] [/direct] [/eightbit] [/unload] [/help] The full list of the parameters is described in the following section of this document. IMPORTANT ! Incorrect use of parameters may result in faulty operation of the PCMCIA adapter. Make sure you are familiar with the different parameters before using them. 4. The Practical PC336 ENET Support Driver parameters --------------------------------------------------- IMPORTANT NOTE. THIS SECTION IS FOR EXPERIENCED USERS ONLY! Using the Practical Wizard program you can install and configure the PC336 ENET Support Driver in a much easier and safer way. ÕÍÍÍÍÍÍÍÍÍÍÍÑÍÍÍÍÍÑÍÍÍÍÑÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ͸ ³ Keyword ³Range³Def.³ Description ³ ÆÍÍÍÍÍÍÍÍÍÍÍØÍÍÍÍÍØÍÍÍÍØÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ͵ ³irq *³ 2-F ³ 0A ³ Specifies the IRQ interrupt line for the PCMCIA ³ ³ ³ ³ ³ adapter. ³ ÃÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÅÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ ³intm ³ 3,4 ³auto³ Specifies the modem (COM) interrupt. The default ³ ³ ³ ³ ³ is the associated COM port interrupt. ³ ÃÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÅÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ ³inte ³ 2-F ³ 5 ³ Specifies the Ethernet interrupt. ³ ÃÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÅÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ ³mem *³D000-³D000³ Specifies the segment of RAM where the adapter ³ ³ ³DC00 ³ ³ will map its attribute (flash) memory. ³ ÃÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÅÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ ³iom ³auto ³auto³ Specifies the modem (COM port) I/O base address. ³ ³ ³ ³ ³ The default value is the standard COM port address ³ ³ ³ ³ ³ for unused COM port. ³ ÃÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÅÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ ³ioe ³auto ³300 ³ Specifies the Ethernet I/O base address. ³ ÃÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÅÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ ³socket *³ 0,1 ³auto³ Specifies the host computer PCMCIA slot where the ³ ³ ³ ³ ³ PCMCIA adapter is inserted. ³ ³ ³ ³ ³ The use of this parameter disables socket auto ³ ³ ³ ³ ³ detection by the driver. ³ ÃÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÅÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ ³type ³ 0-4 ³ 0 ³ Specifies the type of the host computer PCMCIA ³ ³ ³ ³ ³ controller. The types currently defined are: ³ ³ ³ ³ ³ 0 - Auto detection of the PCMCIA controller type³ ³ ³ ³ ³ 1 - Intel 365SL PCIC compatible controller ³ ³ ³ ³ ³ 2 - Databook TCIC compatible controller ³ ³ ³ ³ ³ 3 - Socket Services software ³ ³ ³ ³ ³ 4 - Card & Socket Services software ³ ³ ³ ³ ³ Other values are reserved and must NOT be used. ³ ÃÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÅÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ ³base *³auto ³auto³ Specifies the base I/O address of the host computer³ ³ ³ ³ ³ PCMCIA controller. May be used only for a PCMCIA ³ ³ ³ ³ ³ controller with non-standard I/O address settings. ³ ÃÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÅÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ ³eightbit *³ n/a ³ n/a³ Specifies 8-bit width I/O operations for the ³ ³ ³ ³ ³ PCMCIA adapter. It should be used only for PCs ³ ³ ³ ³ ³ that have an 8-bit (instead of 16-bit) PCMCIA ³ ³ ³ ³ ³ bus interface. ³ ³ ³ ³ ³ For example, you need to use this keyword with the ³ ³ ³ ³ ³ Grid 2260 and AST PenExec computers. ³ ÃÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÅÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ ³fast *³ 0,1 ³ 0 ³ Add additional I/O wait states if non-zero value ³ ³ ³ ³ ³ is specified. This parameter is required by some ³ ³ ³ ³ ³ computers that have a fast I/O bus. ³ ÃÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÅÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ ³direct ³ n/a ³ n/a³ Use direct enabler, ignore Card Services software. ³ ³ ³ ³ ³ This parameter should NOT be used normally. It's ³ ³ ³ ³ ³ for debugging purposes only. ³ ÃÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÅÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ ³audio ³ 0,1 ³ 1 ³ Switch the modem's speaker off/on during the ³ ³ ³ ³ ³ initialization. Use audio=0 if you hear a noise ³ ³ ³ ³ ³ when the driver is being loaded. The noise may be ³ ³ ³ ³ ³ caused by a conflict with a sound card. ³ ÃÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÅÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ ³unload ³ n/a ³ n/a³ Unload the Support Driver from the memory. ³ ³ ³ ³ ³ May be used only with the driver that was loaded ³ ³ ³ ³ ³ from the DOS command prompt or from a batch file. ³ ÀÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÁÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ NOTE. The parameters marked with '*', may or will be ignored, if Card Services software is loaded. 5. Location of Win 95 INF file The inf files necessary to configure your Practical PC336 ENET Card can be found in the root directory of this diskette. (A:\) PPMF.INF PPNDIS.VXD MDMPP.INF NETPP.INF 6. Technical Support -------------------- Phone: 770-840-9966 (US) 905-472-1999 (Canada) Fax: 770-734-4601 Internet: http://www.practinet.com Before contacting for assistance please have the following information ready: - All messages are displayed on the screen; - System version and configuration files. < End of the README >Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.