ZyXEL Communications Services GmbH.
edited by Manfred Recla
June 29, 2000
Release Note on ZyXEL "omni.net PLUS"
Version 4.26 06/08/2000
====================================
1.) The file names and the switch type are as follows:
========================================================
FILENAME SWITCH TYPE
1.1 "OP_E426.BIN" ------ DSS1
2. Fixed bugs:
========================================================
2.1 Using outgoing data call of X.75 or V.110 after 3-way conference call.
These test steps are listed below:
(a)Phone A or Phone B dial to remote side Phone C, then Phone C answer.
(b)Phone A or Phone B press Flash/0, then dial to remote side Phone D,
and Phone D answer.
(c)Phone A or Phone B press Flash/3, then 3-way conference is established.
(d)Phone A or Phone B OnHook, then remote side Phone C and D OnHook.
(e)Using outgoing data call of X.75 or V.110.
2.2 For Denmark, When POTS port connect over five telephones, the CLID function
can work normally.
2.3 For France, using V.120 protocol transmit file between CXR ISDN modem and
TA in pcANYWHERE environment. It can work normally.
2.4 For UK, if the switch(AXE10 system) send public type of number, the call
forwarding interrogation must work normally.
2.5 For UK, the phone OffHook after loopback test, it can't hear any noise.
The test diagram and procedure are described below:
10000 20000
ISDN TA1 -------------- SW ----- ISDN TA2
| | | |
Phone1 Phone2 ISDN telephone PhoneA
(A)TA2 run H/W test, then loopback test.(Using ICM or AT command)
(B)ISDN telephone dial to PhoneA.
(C)PhoneA OffHook can't hear any noise.
2.6 For CAPI mode, softfax can not receive fax from fax machine.
2.7 For CAPI driver mode, TA can not answer x.75 call from remote side.
2.8 For dial-up network, TA can not accept AT command more than 16 digit.
2.9 TA might reset itself when doing PnP process with PC via COM port.
2.10 Making intercom from phone A to phone B, then another analog call
comes in. Pick up the incoming call and form 3 way conference. At this
moment, hook on phone A, the link between phone B and remote should be
kept but it does not.
2.11 TA cannot receive G4 fax when running RVS_COM application
2.12 TA stays in RVS_COM mode after quit the application. This will cause
the MSN setting not work.
2.13 Too many retry errors produced when transferring files by V.110 protocol.
2.14 For AOC function, ATCH? will display incorrect charge information while
the amount is too large.
2.15 Loop back test in ICM.
2.16 Send calling party number when making outgoing voice calls.
2.17 Using outgoing data call of X.75 or V.110 after 3-way conference call.
These test steps are listed below:
(a)Phone A or Phone B dial to remote side Phone C, then Phone C answer.
(b)Phone A or Phone B press Flash/0, then dial to remote side Phone D,
and Phone D answer.
(c)Phone A or Phone B press Flash/3, then 3-way conference is established.
(d)Phone A or Phone B OnHook, then remote side Phone C and D OnHook.
(e)Using outgoing data call of X.75 or V.110.
2.18 For UK, when CLID function over 9 digits, it should display from first
number on the LCD display panel.
3. New Features:
========================================================
3.1 Support call forwarding and new interrogation function for UK, these
relatived AT commands and S-registers are described below:
(a)Relatived AT commands:
ATCFxy(forwarded number): Activate call forwarding
where
x = U : call forwarding unconditional(CFU)
x = B : call forwarding busy(CFB)
x = NR : call forwarding no-reply(CFNR)
where
y = A : Phone A
y = B : Phone B
y = I : Data call
y = S : All services
ATCFxy: Deactivate call forwarding
(b)Relatived S-registers:
S118, S109 and S111 are relatived with call forwarding basic services.
These relatived meaning are explained below:
(1)S118.4=0, don't care S109 and S111 : Using 3.1K Audio basic servies
for Phone B
S118.5=0, don't care S109 and S111 : Using 3.1K Audio basic servies
for Phone A
(2)S118.4=1 and S109=0 : Using Speech basic servies for Phone B
S118.5=1 and S111=0 : Using Speech basic servies for Phone A
(3)S118.4=1 and S109=1 : Using 3.1K Telephony basic servies for Phone B
S118.5=1 and S111=1 : Using 3.1K Telephony basic servies for Phone A
(c)Add interrogation function AT commands:
(1)ATCFA? : For Phone A interrogation
(2)ATCFB? : For Phone B interrogation
(3)ATCFI? : For Data call interrogation
3.2 Support call deflection function for UK, these relatived AT commands and
S-registers are described below:
(a)Relatived AT commands:
ATCFDz(forwarded number): Activate call deflection
where
z = A : Phone A
z = B : Phone B
z = I : Data call
(b)Relatived S-registers:
These S-registers of call deflection basic services are the same as
call forwarding basic services.
3.3 Add call forwarding All services AT commands for UK, these relatived
commands are explained below:
ATCFxSy(forwarded number): Activate call forwarding All services
where
x = U : call forwarding unconditional(CFU)
x = B : call forwarding busy(CFB)
x = NR : call forwarding no-reply(CFNR)
where
y = A : Phone A
y = B : Phone B
y = I : Data call
ATCFxSy: Deactivate call forwarding All services
3.4 For UK, using RVS_COM AT command mode application, if MSN is matched with
POTS port1 or port2 and S51 register is equal to n, the incoming call
will transfer to RVS_COM after n seconds automatically.
where
S51=0: If MSN is matched with the POTS port1 or port2, the POTS port1 or
port2 will ring, it can't transfer to RVS_COM.
S51=n: Unit is second, if MSN is matched with the POTS port1 or port2,
the POTS port1 or port2 will ring. If the POTS port can't answer
after n seconds, the incoming call will transfer to RVS_COM
automatically.
=================================================================================
Release Note on ZyXEL "omni.net PLUS"
Version 4.25 02/22/2000
====================================
1.) The file names and the switch type are as follows:
FILENAME SWITCH TYPE
1.1 "OP_E425.BIN" ------ DSS1
2.) Bug fixed:
==========================
2.1 Solve U model compatibility problem to some Siemens switches:
In previous firmware, when connect U model to some Siemens
switches, the link can be established such the TA does not work.
This bug is fixed in V 4.25.
2.2 Firmware v4.24a does not work on S/T model.
This bug has been fixed in v4.25.
=================================================================================
Release Note on ZyXEL "omni.net PLUS"
Version 4.24 12/03/1999
====================================
1. The file names and the switch type are as follows:
=====================================================
FILENAME SWITCH TYPE
1.1 "OP_E424.BIN" ----- DSS1
2. Modifications:
==========================
2.1 Long distance call control:
As user's request, the long distance call control must be protected
by password, the control bits S91.0, S91.1 defined in firmware V4.23
are not used any further. The control of enable/disable the long
distance call on POTS port is protected by supervisor password now.
Please refer to the following description on the function:
This feature is used to restrict the long distance call dialing from
the two analog ports. When the phone port is locked, all phone
dialing starting with '0' will be automatically disconnected by TA.
Please note the setting of the feature is protected by system
password. Relating AT commands are listed below:
ATSK=n
where n=0 : unlock both phone port
1 : lock phone 1 only
2 : lock phone 2 only
3 : lock both phone 1 and phone 2
Please note you are asked entering supervisor password after ATSK=n
command entered. However, viewing the current setting is not
protected and can be done by ATSK? command.
2.2 China U-interface L1 activation:
To reach the maximal switch compatibility, the layer 1 activation
algorithm is modified for China. After upgrade to the newest
firmware, the user should enter 'AT&F&W0Z0' to make the algorithm
work.
2.3 The following factory defaults have been changed for China (222):
S121.4=1: always keep layer 2 link on
ATY2 : ETSI FSK caller id generation during ring 1 and ring 2.
============================================================================
Release Note on ZyXEL "omni.net PLUS"
Version 4.23 11/11/1999
====================================
1.The firmwares' file names for various switch types are as follows:
FILENAME SWITCH TYPE
"OP_E423.BIN" ---- DSS1
2. New enhancement features
==========================
2.1 Long distance call enable/disable bit:
Users can enable/disable the long distance outgoing voice call on POTS
ports. When the ability is disabled, if the first dialed digit is '0',
the call attempt will be rejected automatically.
S91.0 = 0 : enable long distance call for POTS 1 (default)
= 1 : disable
S91.1 = 0 : enable long distance call for POTS 2 (default)
= 1 : disable
2.2 Deem AT&F as ATZ:
Some application program running on PC will issue AT&F when initializing
TA. But users might need to have their own setting work under the
application. In this case, user can set ATS90.1=1&W0Z0. With S90.1=1,
the command AT&F will be executed the same as ATZ so that the users'
setting will not be affected.
2.3 POTS port MSN matching algorithm when running RVS-COM application:
In previous firmware, when running RVS-COM, the incoming voice call will
be routed to RVS-COM no matter if the called party number matches the
internal phone MSN or not. This behaviour is modified as below:
The called party number (= MSN) of incoming voice call is compared with
the internal MSN setting of the POTS ports, if it matches, then the call
is routed to the POTS port. If there is no POTS MSN matched in the
comparison, the call will be routed to RVS-COM application.
2.4 No busy tone after voice call is disconnected by the remote user:
Some answering machine cannot react to busy tone after the remote user
leaves message and hangs up the call, it just keep recording. Two S bits
are defined for blocking the busy tone for each POTS port so that the
answering machine can detect silence for a period of time and then stop
recording.
S78.0 = 1 : disable busy tone for POTS port A
= 0 : normal
S78.1 = 1 : disable busy tone for POTS port B
= 0 : normal
Note: these bits have been defined to work for locally generated busy
tone. This enhancement works for both inband and local busy tone.
2.5 Support Taiwan country code 210 for A-law codec:
Both A-law and u-law codec schemes are used in Taiwan now. So we need
specify the country code if the default codec mode does not comply with
the local switch.
Country code 238: default for Taiwan, u-law CODEC
Country code 210: Taiwan, A-law CODEC
3. Fixed Bugs:
==========================
3.1 Set China default CLID signal on POTS port as ETSI FSK, during ring.
3.2 Set S121.4=1 as China default to keep ISDN layer always on.
3.3 For UK, country code 249, the calling party number is purposely dropped
in the setup message. Otherwise, there will no dial tone presented for
some old switch. This feature is now enabled since there is less old
switches in the U.K now.
=================================================================================
Release Note on ZyXEL "omni.net PLUS"
Version 4.22 07/19/1999
====================================
1.The firmware file names for various switch types are as follows:
FILENAME SWITCH TYPE
"OP_E422.BIN" ----- DSS1 ....... binary firmware file for
EuroISDN (Europe, Asia, Australia)
not available ---- USA
not available ---- 1TR6
2.New enhancement features
==========================
2.1 now supports Call Waiting (CW) ISDN supplementary service
for New Zealand.
3.Fixed Bugs:
==========================
3.1 In CAPI driver mode, RVS-COM's "Softfax" can not receive fax from
external fax machines.
3.2 In CAPI driver mode, TA can not answer X.75 call from remote side.
3.3 For Australia, TA should ignore "INFO" message without Called Party
Number (MSN) while TA is in "Overlap Sending" state.
3.4 For Australia, TA should send "SETUP" message without "Sending
complete" information element.
3.5 TA cannot receive G4 fax when running RVS_COM application
3.6 TA stays in RVS-COM mode after quitting the application. This
will cause the MSN settings not working anymore in normal mode.
3.7 Too many retry errors produced when transfering files by V.110
protocol.
3.8 For AOC (Advice Of Charging) function, ATCH? command will display
incorrect charge information while the amount is too large.
-----------------------------------------------------------------------------
Release Note on ZyXEL "omni.net PLUS"
Version 4.21 06/16/1999
====================================
1. Firmware file name and corresponding switch type:
========================================================
FILENAME SWITCH TYPE
"OP_E421.BIN" ---- DSS1
not available ---- USA
not available ---- 1TR6
2.New enhancement features
==========================
2.1 now TA supports the synchronous mode (V.25bis command set)
to transmit ISDN data using the B-channel protocol V.110 (64kbps sync.)
synchronous mode compatibility with IBM AS/400 machine:
Since there are different implementation options choosen by data terminal
equipment manufacturers, there is one more S register bit used to switch
the operation mode of the protocol.
The setting for IBM style DTE are listed below:
calling: AT&FB11S80.6=1S0=0S122.7=1&M3*I1&W0Z0
answering: AT&FB11S80.6=1S0=1S122.7=1&M3*I1&W0Z0
No other parameters are needed to be set when S122.7=1 is used as above.
There is a V.25bis state machine controlling all the DSR,CTS,RI,DCD
signals in this mode.
3.Fixed Bugs:
==========================
3.1 For Korea, the Call Forwarding should use KEYPAD information element
to send the dialed number.
3.2 TA might reset itself when doing PnP process with PC via COM port.
3.3 Adjust Hook Flash timing to comply with Denmark specification.
3.4 Making intercom from phone A to phone B, then another analog call
comes in. Pick up the incoming call and perform a 3PTY conference.
At this moment, hook on phone A, the link between phone B and remote
should be kept - but it did not.
3.5 For UK (country code 249) if the incoming phone call does not carry
CallerID information in D-channel, then TA will malfunction.
(no RING on POTS ports)
3.6 ATCG command will test the analog CallerID function if the hardware
supports that feature.
3.7 Netherland (country code 253): ATCF (Call Forwarding) command is
performed by sending the KEYPAD signaling.
3.8 The following changes have been made specific to these countries:
- 241 (Singapore) -> now supports FSK CallerID signaling
on the POTS ports.
- 249 (United Kingdom) -> the ringing frequency on POTS ports is 25Hz
- 225 (Swizerland) -> now supports DTMF CallerID signaling
on the POTS ports.
- 222 (China) -> now supports KEYPAD signaling on POTS ports
=============================================================================
Release Note on ZyXEL "omni.net PLUS"
Version 4.20 04/14/1999
====================================
1. Firmware file name and corresponding switch type:
========================================================
FILENAME SWITCH TYPE
"OP_E420.BIN" ---- DSS1
not available ---- USA
not available ---- 1TR6
2. New Features:
================
None
3. Fixed Bugs:
===============
3.1 The LNK LED will blink sometimes when unplug the ISDN line.
3.2 For Loopback 2 test, it should turn off the LNK LED.
3.3 Fix ATCG Phone A & Phone B test bugs. If don't care the phone A test,
phone B test will halt.
============================================================================
Release Note on ZyXEL "omni.net PLUS"
Version 4.19 03/25/1999
====================================
not officially released - internal test only
============================================================================
Release Note on ZyXEL "omni.net PLUS"
Version 4.18 01/25/1999
====================================
1. Firmware file name and corresponding switch type:
========================================================
FILENAME SWITCH TYPE
"OP_E418.BIN" ---- DSS1
"OP_A418.BIN" ---- USA
not available ---- 1TR6
2. New Features:
================
2.1 Modify the Layer 1 driver for Siemens ISDN chip PEB8191
3. Bugs fixed:
=============
3.1 ATCG for omni.net Plus (U) - USA model - can work now.
3.2 The Loopback 2 function is fixed.
============================================================================
Release Note on ZyXEL "omni.net PLUS"
Version 4.17 12/03/1998
====================================
1. Firmware file name and corresponding switch type:
========================================================
FILENAME SWITCH TYPE
"OP_E417.BIN" ---- DSS1
2. New Features:
================
2.1 Adding ATX8 result code: with the result code set defined as ATX8,
2.1.1 The ring message is displayed as:
RING
FM:5783942
TO:5774848
RING
FM:5783942
TO:5774848
..........
2.1.2 The connect message is displayed as:
CARRIER 64000
PROTOCOL: V120
ERROR CONTROL: LAPD
COMPRESSION: V42b
CONNECT 460800
2.2 Adding command to switch on/off the compression when make a PPP/MP call:
ATJH0 : switch off the compression on DTE, the compression will be done
inside the TA.
ATJH1 : switch on the compression on DTE if available
The current setting of ATJH0 or ATJH1 can be viewed by command ATI11.
2.3 Compatible with RVS-COM's "softfax" and EFT (EuroFileTransfer) functions.
2.4 Show caller ID information with each ring message if S121.3 is set to 1.
For example:
RING
FM:1234 TO:5678
RING
FM:1234 TO:5678
3. Bugs fixed:
=============
3.1 correcting bug of which the Microsoft Windows9x/NT4 "UNIMODEM" legacy ID
cannot be recognized when install the TA under Windows9x/NT4 environment.
3.2 The ring cadence should be 1 second on, 4 seconds off for Slovakia (228)
and Czechia (246).
3.3 Adding "SENDING COMPLETE" information element in D-channel outgoing SETUP
message for ISDN data call so that the ISDN switch reacts faster than
with previous firmware versions. Some PABXs need the SENDING COMPLETE
information.
3.4 Correcting bug which the call history is not recorded after power on
reset.
3.5 TA can not answer V.110/9.6K call from GSM mobile phone data calls.
3.6 "A>" or "A/" will cause TA reset.
-----------------------------------------------------------------------------
Release Note on ZyXEL "omni.net PLUS"
Version 4.16 08/21/1998
====================================
1. Firmware file name and corresponding switch types:
=====================================================
FILENAME SWITCH TYPE
"OP_E416.BIN" -------- Europe DSS1
2. Bugs fixed:
=============
2.1 Bug fixed: PPP/MP with bundle and compression set together doesn't work.
2.2 Support KeyPad signaling in Switzerland in country code: 225
note: KeyPad signaling is used for the ISDN supplementary service
like "Call Forwarding"
-----------------------------------------------------------------------------
June 29, 1998
Release Note on omni.net PLUS Version 4.15
==========================================
1.The firmwares' file names for various switch types are as follows:
FILENAME SWITCH TYPE
"MP128E.415" ------ Europe DSS1
==========================================================================
2 Important message:
After upgrade Omni.net PLUS by this F/W, the TA will perform "hardware
reset" automatically. This is because the EEPROM usage has been
rearranged in the firmware. All data stored in EEPROM will need to be
reload after the process. Please note this process happens only at the
first time upgrading.
==========================================================================
3. New implementations:
-----------------------
3.1 Service provider preselect number:
AT&ZP? : display the number setting
AT&ZPI=xxxxxxx : set the number for data call dial out
AT&ZPA=xxxxxxx : set the number for voice call on phone A
AT&ZPB=xxxxxxx : set the number for voice call on phone B
maximum length for each port is seven
Usage: Please refer to Note 5.1
3.2 Extend the number of digits stored in MSN to 26.
3.3 Adding country code 216 for Spain
3.4 For ITALY, support NNP Spec. for sending out the first 20 dial digits
in Enbloc sending while the remaining by Overlap sending. The maximum
number of the dialing digits is 25.
3.5 support EuroFile Transfer (ATB42) for RVS-COM v1.37 (and higher)
3.6 "R"-key operation for ISDN supplementary services (Sweden 250 only)
Usage: Please refer to Note 5.2
3.7 User selectable caller ID signaling
Select one caller ID signaling method out of several poupular standards
by following AT command: (available on Caller ID H/W only)
ATY0 : country default
ATY1 : DTMF, prior to ring
ATY2 : ETSI FSK, during ring
ATY3 : ETSI FSK, prior to ring
Usage: Please refer to Note 5.3
4. Enhancement/Bug fixed:
==========================================================================
4.1 Accept command stream such as:
at&zoi=1111;&zoa=2222;&zob=3333 <enter>
at&zpi=1111;&zpa=2222;&zpb=3333 <enter>
at&zi0=1111;&zi1=2222;&zi3=3333 <enter>
For backward compatibility, command streams not separated by semicolon
are also supported.
at&zoi=1111&zoa=2222&zob=3333 <enter>
at&zpi=1111&zpa=2222&zpb=3333 <enter>
at&zi0=1111&zi1=2222&zi3=3333 <enter>
4.2 For Korea, AT&T11 will not compare the calling party number since the
information element is not available.
4.3 For Japan, enhance the 3 minutes restrictions on dialing out data call.
In Japan ISDN, for data call,the phone number destinated to the same
place cannot be dialled during 3 minutes.
4.4 ISDN Callback function based on CallerID on D-channel
4.5 Hold/Retrieve, then atqp2/atqp3 will generate lots of garbages.
4.6 Supplementary Service requirement in Portugal
4.7 Layer 3 message longer than 128 octets was not intepreted properly
4.8 Called Party Number should be unknown numbering plan in ITALY
4.9 Support analog Caller ID feature on POTS ports for the following
countries:
U.K
Norway
Germany
France
4.10 Supress "NO CARRIER" message when callback
4.11 Fix bug: Onhook during conference call will generate garbages.
4.12 Enhancement on ISDN supplementary service: (S120.7=1)
Now you can use the Hold/Retrieve service whether 3PTY is available or
not,
4.12.1 When service Hold, Retrieve and 3PTY are all available
- Make an outgoing call from phone port A
- Knocking the "Hook Flash" to get dial tone.
- Make second outgoing call from the same port
- After the second call connected, you have the first call on hold and
the second active.
- Knocking the "Hook Flash" again will try to build 3 way conference
call
- If the conference mode is entered successfully, all the three parties
can talk on the same channel.
- In conference mode, disconnect from any remote user will end the
conference mode while keep the remaining link active. Thus you can
continue the coversation with the other remote user
- In conference mode, put onhook will end the conference mode and
disconnect both links.
4.12.2 When only service Hold and Retrieve are available:
- Refer to 12.1, if the attempt to enter conference mode fails, you can
toggle between the two calls by knocking "Hook Flash" alternatively.
5. Note:
==========================================================================
5.1 Along with the opening on Telcom market, there might be certain service
providers available in one country. Users live in these countries have
options on selecting the provider per call with the dial-preselect digits.
The dial out numbers become:
<pre-select digit> + <called party number>.
With AT&ZPx command in this F/W, users can specify the pre-select digits
in respect to Phone A, Phone B, and Data call. These digits will be stored
in EEPROM and will be automatically inserted in front of the called party
number when making call attempts.
5.2 R key operations: currently, it works only for Sweden, country code 250
Operations: After the related supplementary services subscribed, you can,
5.2.1 Outgoing call:
5.2.1.1 - make an outgoing voice call on phone A
- after connected, press "R" key to hold the active call and dial the
second call
- during the dialing, you can give up the call attempt by press "R"
- when the ring back tone heard but no answer at the remote site, you
can give up the call by "R" as well.
- if the called party pick up the call, you can press "R"+"2" to switch
between these two calls (this is Hold/Retrieve)
5.2.1.2 - Following 5.2.1.1, after both call connected
- Press "R"+"2" will switch between these two calls
- Press "R"+"1" will disconnect the active call and retrieve the other
call on hold.
- Press "R"+"3" will make a conference call.
5.2.1.3 - When the conference mode is entered by "R"+"3" as mentioned in 5.2.1.2,
press "R"+"3" again will end the conference mode and will bring you
back to previous state, one call active and the other on hold.
- Please note that in conference mode, any key combination other than
"R"+"3" will be ignored.
- When in conference mode, go onhook will terminate all voice links
connected to the phone.
5.2.1.4 - If the conference mode is not available or you do not subscribe it,
press "R"+"3" works just like "R"+"2", toggle between the two calls.
5.2.2 Incoming call waiting:
5.2.2.1 - established a connection on phone A
- if there comes a second voice call and is routed to phone A, you will
hear a "Du-Du" tone for about 15 seconds.
- at this point, you can either
(1). press "R"+"0" to reject the call, or
(2). press "R"+"1" to release the active call and pick up the call, or
(3). press "R"+"2" to hold the active call and pick up the incoming
call.
- if "R"+"2" is pressed, all actions mentioned in 5.2.1.2 apply.
5.3 User configurable caller ID signaling method:
In most cases, the calling party number is available in ISDN call in a
digital way. The Omni.net PLUS with CLIP hardware will generate the analog
caller ID signal to phone ports so that users' devices with LCD can display
the calling party number just as connecting to PSTN. However, there are
several methods for sending the signaling out. In this F/W, some countries'
specifications are available so the signaling method is loaded automatically.
For other countries of which spec. unknown, users can use ATYx command to try
out a suitable signaling to his/her own display device. Furthermore, with
this command, users can use display devices without restrictions on the
signaling methods.
=============================================================================
note: versions 4.13, 4.14 were not publically released !
=============================================================================
Release Note on Omni.net PLUS Version 4.12 May 7th, 1998
==========================================
FILENAME SWITCH TYPE Checksum
"MP128E.412" DSS1 35F1
Based on V 4.11, the following modification have been made:
1. Denmark ring cadence : 1 second on, 5 second off
2. Denmark ring frequency : default to 25Hz, s121=2
3. Sweden ring frequency : default to 25Hz, s121=2
=============================================================================
Release Note on omni.net PLUS Version 4.11 Apr. 7, 1998
==========================================
1.The firmwares' file names for various switch types are as follows:
FILENAME SWITCH TYPE
1.1 "MP128E.411" ------ DSS1
1.2 "MP128G.411" ------ 1TR6
2.New implemented features
==========================
2.1 New proprietary feature phone functions(for DSS1 and USA only)(Note 1)
2.1.1. Redial,
2.1.2. Quick dial,
2.1.3. Incoming/outgoing call history.
2.2 Multi-auto Dial Out(MDO) for outgoing data call.
Automatically try the outgoing data protocol with predefined
protocol sequence.
2.2.1. Command Listing:
AT command s122.4 .3 .2 Trail Sequence
ATB90 0 0 0 PPP+X.75
ATB91 0 0 1 PPP+X.75+T.70+ISO8208+T.90+BTX
ATB92 0 1 0 X.75+T.70+ISO8208+T.90+BTX+PPP
ATB93 0 1 1 PPP+V.120
ATB94 1 0 0 V.120+PPP
ATB95 1 0 1 PPP+X.75+V.120 (* default for DSS1,1TR6)
ATB96 1 1 0 PPP+V.120+X.75 (* default for U.S.A)
ATB97 1 1 1 X.75+V.120+PPP
2.2.2. Restrictions:
2.2.2.1. Bundle call is not supported in MDO.
2.2.2.2. With s80.6 set to 1,LLC enabled, no MDO function available.
2.2.2.3. During MDO dialing, the trial sequence will be wrap around
until S7 timer expired.
2.2.2.4. Disconnect from the peer site will end the trail sequence.
2.3 For USA, modify LNK LED indications.
OFF : power down, SPID negotiation fail,
Slow blinking : activating layer 1(ISDN line physical link),
Fast blinking : negotiating SPID,
ON : ISDN link success.
2.4 For USA, stick DN and B-channel on data port and POTS port.
For the data port(V.120, PPP....) or POTS port(POTS 1 or POTS 2),
if AT&ZIn = DN0(or DN1), then an outgoing call will occupy
DN0 & B1(or DN1 & B2) channel.
2.5 For USA, select the preferred B-channel for outgoing
data call by set S-register s122 bit 0 & bit 1.
S122.0, s122.1 Preferred B-channel
--------------------------------------------
= 0 0 ,Any channel(default),
= 1 0 ,B1 channel preferred,
= 1 1 ,B2 channel preferred.
2.6 For DSS1, implement supplementary services:
2.6.1 Three party conference,(Note 2)
2.6.2 Call forwarding(CFU, CFB, CFNR).(Note 3)
2.7 For USA NI-1, DMS-100 switch, implement supplementary services
2.7.1 ACO(call waiting),(Note 2)
2.7.2 Call hold/retrieve,(Note 2)
2.7.3 Flexible calling(conference, drop, transfer),(Note 2)
2.7.4 Call forwarding,(Note 3)
2.7.5 Message waiting,(Note 4)
2.7.6 Reminder Ring.(Note 3)
2.8 Implement charging advice(advice of charge, AOC) function for Italy.
Issue ATCH? to see the charging information during or after the calls.
2.9 When a phone call comes in to the a/b adapter,
s78.2 = 0, disable the RING response to DTE port for analog port(default).
s78.2 = 1, enable this function.
3.Fixed the Bugs:
=================
3.1 EPA modification for supplementary services.
3.2 For S-register in online help, modify s119.1, s119.2, and fix the
wrapped lines in s119, s120, and s121.
3.3 Fix bug of TA128 connects to Cisco 2511. After about one day of normal
operation; the TA128 cannot connect any incoming PPP call.(71103-1156)
3.4 S56 default value depends on country.
3.5 Ringer frequency should automatically saved in NVRAM when country code
is set.
3.6 Keypad signalling function for Neitherlands(253), Denmark(252),
Norway(245), Finland(240).
3.7 For Italy(236) PNN, the maxinum number of dialing digits should be 25.
3.8 For Ireland(235), ring cadence should be 0.2s-0.2s-0.2s-2.0s,
3.9 For Thailand(227), ring frequency: 25hz; ring cadance: 1 sec. on 4 sec.
off; dial tone: 400hz modulation by 50hz; dial tone period: continuous;
busy tone frequency: 400hz; busy tone period: 0.5 sec. on 0.5 sec. off
3.10 For Australia, always enable the tones(dial, busy, ring back...) from
the switch.
3.11 Keypad signalling cannot work for service interrogating signalling
(*#....#).
4.Notes:
========
Note 0: To invoke all the supplementary services, you should subscribe
the services that you want from your phone company. Then issue
ATs120.7=1&w0z0.
s120.7 : flash key usage
= 0, invoke feature phone when press the flash key;
= 1, invoke supplementary service when press the flash key.
Notice: you can not use pluse dialing while you use supplementary
service functions(i.e. when s120.7=1 is set).
Note 1: How to use the new feature phone functions.
Pick up the hand set, press the flash key(or push the hook key
then release it immediately), then dial the following command
digits:
i. Redial: **
Redial the last dialed number. The last numbers(phone 1 & 2)
will be stored in NVRAM(AT&Z38 and AT&Z39), so you can redial
the last number after power off and on the TA.
ii. Quick dial:
There are 10 set of number for each POTS port. These numbers
will be stored in NVRAM(AT&Z0~AT&Z9 for POTS 1, AT&Z10~AT&Z19
for POTS 2).
2.1 Set phone numbers - *0n*phone-number#,
2.2 Clear phone numbers - *0n*#,
2.3 Quickly dial - *0n#, where n = 0~9.
2.4 Display the phone numbers stored via AT command, issue
ATQP1.
iii. Incoming/outgoing call history:
The TA will store 20/20 set of phone numbers for incoming/outgoing
call history for each POTS port.
If the global answer function(s120.2=0) is enabled, or no distinct
MSN number for phone 1 and phone 2, an incoming call's number will
be stored to phone 1's call-in history.
To display the call-in history via AT command, issue
ATQP3.
To display the call-out history via AT command, issue
ATQP2.
iv. Phone command list for 2.2.1, 2.2.2, 2.7.2, & 2.8.4
+-----------------------------+------------------------------+
|** |Redial |
+-----------------------------+------------------------------+
|*0n# ,n=0~9|Quick dial(speed dial) |
+-----------------------------+------------------------------+
|*0n*phone-number# ,n=0~9|Set quick-dialed number |
+-----------------------------+------------------------------+
|*0n*# ,n=0~9|Clear quick-dialed number |
+-----------------------------+------------------------------+
|*2m*forwarding-number# ,m=0~2|Call forwarding activation |
+-------------------------+----------------------------------+
|#2m# ,m=0~2|Call forwarding deactivation |
+-----------------------------+------------------------------+
For the last two call forwarding commands, they are for call
forwarding supplementary services. Please refer to note 3.
Note 2: How to invoke these supplementary service: call waiting, call hold,
conference, (& drop, transer for USA).
First, subscribe the services that you want from your telephone
company. Issue ATS120.7=1&W0Z0 to save in NVRAM.
For USA version, you need to save the IOC(ISDN Ordering Code,
feature access code) to the TA by
AT&ZF0=IOC_of_CONFERENCE
AT&ZF1=IOC_of_TRANSFER
AT&ZF2=IOC_of_DROP
These IOC should be in the range of 0-63.
i. Call Waiting(s79.6=1 for 2864I, s79.2=1, s79.3=1 for TA128):
When you are talking on a phone call and another phone call
comes in, you will hear a tutut tone. Press the flash key
to hold the first call and pick up the second call.
If you want to switch back to the first call, press the flash
key again.
ii. Three-Party Calling(Call Hold & Conference):
Place a first phone. After connection, press the flash key
to hold the first call. You will get a dial tone and place
the second call. After connect, press the flash again, then
you will have a conference call.
(DSS1)If you want to cancel the conference, press the flash.
(USA) If you want to drop the last call added to the
conference, press the flash again.
If you want to drop yourself from the conference call,
just hang up the phone.
iii. Call Transfer(USA only):
You should have a conference call at first(just follow the
steps of ii), then hang up the phone and okay.
Blind Transfer(USA only):
You should have a phone call at first. Press the flash key
and then get a dial tone. Dial the phone number you want to
transfer the first call. After the second call ring back,
hang up the phone. You don't need to wait the second one
answer it.
Note 3: How to invoke the call forwarding service (& reminder ring for USA):
For DSS1, we support the call forwarding unconditional(CFU),
call forwarding busy(CFB),
call forwarding no-reply(CFNR).
And you should set your own numbers first(AT&ZO?).
i. Activated by AT commands:
ATCFxy(transfer-number)
x=B Call forwarding busy(CFB),
U Call forwarding unconditional(CFU),
NR Call forwarding no-reply(CFNR).
y=S All services,
I ISDN data(unrestricted digital),
B POTS port, phone,
M Internal modem.
ii. Deactivated by AT commands:
ATCFxy
iii. Activated by phone flash command(only forwarding phone call):
Off hook, do a flash, then dial
*20*transfer-number# for CFB,
*21*transfer-number# for CFU,
*22*transfer-number# for CFNR.
iv. Deactivated by phone flash command(phone call only):
Off hook, do a flash, then dial
#20# for CFB,
#21# for CFU,
#22# for CFNR.
v. Query the status of the call forwarding. Simply issue
ATCF?
For USA NI-1 & DMS-100 switch, we support the Call Forwarding
Variable(CFV) service. Before you invoke this feature,
you need to save the IOC(ISDN Ordering Code, feature access
code) to the TA. If you don't know about it, please ask your
phone company.
AT&ZF4=IOC_of_CALL_FORWARDING to save it, IOC=0~63.
AT&ZF? to display it.
i. Activate by AT commands:
ATCF(transfer-number)
ii. Deactivate by AT commands:
ATCF
iii. Activate by phone flash command:
Off hook, do a flash, and dial
*21*transfer-number#.
iv. Deactivate by phone flash command(phone call only):
Off hook, do a flash, and dial
#21#.
Reminder Ring: after you activate the call forwarding function,
you will hear a short ring every time a call has been forwarded.
Note 4: For USA NI-1 & DMS-100 message waiting service, the message service
is activated when you subscribe this service from your phone
company. You need to save the IOC of the message waiting
that your phone company gives you to the TA by
AT&ZF3=IOC_of_MESSAGE_WAITING(0~63)
If you have a waiting message in MSR(Message Storage and
Retrieve system) in the phone company, you will see the B1 & B2
LED blinking. Then you can retrieve you message from the MSR
system.
Once you want to deactivate this service, issue an AT command
ATMW.
==============================================================================
Release Note on Omni.net PLUS Version 4.10 Mar. 27, 1998
===========================================
1.The firmwares' file names for various switch types are as follows:
FILENAME SWITCH TYPE
1.1 "MP128E.410" ------ DSS1
1.2 "MP128A.410" ------ USA
1.3 "MP128G.410" ------ 1TR6
2.New implemented features
==========================
2.1 New proprietary feature phone functions(for DSS1 and USA only)(Note 1)
2.1.1. Redial,
2.1.2. Quick dial,
2.1.3. Incoming/outgoing call history.
2.2 Multi-auto Dial Out(MDO) for outgoing data call.
Automatically try the outgoing data protocol with predefined
protocol sequence.
2.2.1. Command Listing:
AT command s122.4 .3 .2 Trail Sequence
ATB90 0 0 0 PPP+X.75
ATB91 0 0 1 PPP+X.75+T.70+ISO8208+T.90+BTX
ATB92 0 1 0 X.75+T.70+ISO8208+T.90+BTX+PPP
ATB93 0 1 1 PPP+V.120
ATB94 1 0 0 V.120+PPP
ATB95 1 0 1 PPP+X.75+V.120 (* default for DSS1,1TR6)
ATB96 1 1 0 PPP+V.120+X.75 (* default for U.S.A)
ATB97 1 1 1 X.75+V.120+PPP
2.2.2. Restrictions:
2.2.2.1. Bundle call is not supported in MDO.
2.2.2.2. With s80.6 set to 1,LLC enabled, no MDO function available.
2.2.2.3. During MDO dialing, the trial sequence will be wrap around
until S7 timer expired.
2.2.2.4. Disconnect from the peer site will end the trail sequence.
2.3 For USA, modify LNK LED indications.
OFF : power down, SPID negotiation fail,
Slow blinking : activating layer 1(ISDN line physical link),
Fast blinking : negotiating SPID,
ON : ISDN link success.
2.4 For USA, stick DN and B-channel on data port and POTS port.
For the data port(V.120, PPP....) or POTS port(POTS 1 or POTS 2),
if AT&ZIn = DN0(or DN1), then an outgoing call will occupy
DN0 & B1(or DN1 & B2) channel.
2.5 For USA, select the preferred B-channel for outgoing
data call by set S-register s122 bit 0 & bit 1.
S122.0, s122.1 Preferred B-channel
--------------------------------------------
= 0 0 ,Any channel(default),
= 1 0 ,B1 channel preferred,
= 1 1 ,B2 channel preferred.
2.6 For DSS1, implement supplementary services:
2.6.1 Three party conference,(Note 2)
2.6.2 Call forwarding(CFU, CFB, CFNR).(Note 3)
2.7 For USA NI-1, DMS-100 switch, implement supplementary services
2.7.1 ACO(call waiting),(Note 2)
2.7.2 Call hold/retrieve,(Note 2)
2.7.3 Flexible calling(conference, drop, transfer),(Note 2)
2.7.4 Call forwarding,(Note 3)
2.7.5 Message waiting,(Note 4)
2.7.6 Reminder Ring.(Note 3)
2.8 Implement charging advice(advice of charge, AOC) function for Italy.
Issue ATCH? to see the charging information during or after the calls.
2.9 When a phone call comes in to the a/b adapter,
s78.2 = 0, disable the RING response to DTE port for analog port(default).
s78.2 = 1, enable this function.
3.Fixed the Bugs:
=================
3.1 EPA modification for supplementary services.
3.2 For S-register in online help, modify s119.1, s119.2, and fix the
wrapped lines in s119, s120, and s121.
3.3 Fix bug of TA128 connects to Cisco 2511. After about one day of normal
operation; the TA128 cannot connect any incoming PPP call.(71103-1156)
3.4 S56 default value depends on country.
3.5 Ringer frequency should automatically saved in NVRAM when country code
is set.
3.6 Keypad signalling function for Neitherlands(253), Denmark(252),
Norway(245), Finland(240).
3.7 For Italy(236) PNN, the maxinum number of dialing digits should be 25.
3.8 For Ireland(235), ring cadence should be 0.2s-0.2s-0.2s-2.0s,
3.9 For Thailand(227), ring frequency: 25hz; ring cadance: 1 sec. on 4 sec.
off; dial tone: 400hz modulation by 50hz; dial tone period: continuous;
busy tone frequency: 400hz; busy tone period: 0.5 sec. on 0.5 sec. off
3.10 For Australia, always enable the tones(dial, busy, ring back...) from
the switch.
3.11 Keypad signalling cannot work for service interrogating signalling
(*#....#).
4.Notes:
========
Note 0: To invoke all the supplementary services, you should subscribe
the services that you want from your phone company. Then issue
ATs120.7=1&w0z0.
s120.7 : flash key usage
= 0, invoke feature phone when press the flash key;
= 1, invoke supplementary service when press the flash key.
Notice: you can not use pluse dialing while you use supplementary
service functions(i.e. when s120.7=1 is set).
Note 1: How to use the new feature phone functions.
Pick up the hand set, press the flash key(or push the hook key
then release it immediately), then dial the following command
digits:
i. Redial: **
Redial the last dialed number. The last numbers(phone 1 & 2)
will be stored in NVRAM(AT&Z38 and AT&Z39), so you can redial
the last number after power off and on the TA.
ii. Quick dial:
There are 10 set of number for each POTS port. These numbers
will be stored in NVRAM(AT&Z0~AT&Z9 for POTS 1, AT&Z10~AT&Z19
for POTS 2).
2.1 Set phone numbers - *0n*phone-number#,
2.2 Clear phone numbers - *0n*#,
2.3 Quickly dial - *0n#, where n = 0~9.
2.4 Display the phone numbers stored via AT command, issue
ATQP1.
iii. Incoming/outgoing call history:
The TA will store 20/20 set of phone numbers for incoming/outgoing
call history for each POTS port.
If the global answer function(s120.2=0) is enabled, or no distinct
MSN number for phone 1 and phone 2, an incoming call's number will
be stored to phone 1's call-in history.
To display the call-in history via AT command, issue
ATQP3.
To display the call-out history via AT command, issue
ATQP2.
iv. Phone command list for 2.2.1, 2.2.2, 2.7.2, & 2.8.4
+-----------------------------+------------------------------+
|** |Redial |
+-----------------------------+------------------------------+
|*0n# ,n=0~9|Quick dial(speed dial) |
+-----------------------------+------------------------------+
|*0n*phone-number# ,n=0~9|Set quick-dialed number |
+-----------------------------+------------------------------+
|*0n*# ,n=0~9|Clear quick-dialed number |
+-----------------------------+------------------------------+
|*2m*forwarding-number# ,m=0~2|Call forwarding activation |
+-------------------------+----------------------------------+
|#2m# ,m=0~2|Call forwarding deactivation |
+-----------------------------+------------------------------+
For the last two call forwarding commands, they are for call
forwarding supplementary services. Please refer to note 3.
Note 2: How to invoke these supplementary service: call waiting, call hold,
conference, (& drop, transer for USA).
First, subscribe the services that you want from your telephone
company. Issue ATS120.7=1&W0Z0 to save in NVRAM.
For USA version, you need to save the IOC(ISDN Ordering Code,
feature access code) to the TA by
AT&ZF0=IOC_of_CONFERENCE
AT&ZF1=IOC_of_TRANSFER
AT&ZF2=IOC_of_DROP
These IOC should be in the range of 0-63.
i. Call Waiting(s79.6=1 for 2864I, s79.2=1, s79.3=1 for TA128):
When you are talking on a phone call and another phone call
comes in, you will hear a tutut tone. Press the flash key
to hold the first call and pick up the second call.
If you want to switch back to the first call, press the flash
key again.
ii. Three-Party Calling(Call Hold & Conference):
Place a first phone. After connection, press the flash key
to hold the first call. You will get a dial tone and place
the second call. After connect, press the flash again, then
you will have a conference call.
(DSS1)If you want to cancel the conference, press the flash.
(USA) If you want to drop the last call added to the
conference, press the flash again.
If you want to drop yourself from the conference call,
just hang up the phone.
iii. Call Transfer(USA only):
You should have a conference call at first(just follow the
steps of ii), then hang up the phone and okay.
Blind Transfer(USA only):
You should have a phone call at first. Press the flash key
and then get a dial tone. Dial the phone number you want to
transfer the first call. After the second call ring back,
hang up the phone. You don't need to wait the second one
answer it.
Note 3: How to invoke the call forwarding service (& reminder ring for USA):
For DSS1, we support the call forwarding unconditional(CFU),
call forwarding busy(CFB),
call forwarding no-reply(CFNR).
And you should set your own numbers first(AT&ZO?).
i. Activated by AT commands:
ATCFxy(transfer-number)
x=B Call forwarding busy(CFB),
U Call forwarding unconditional(CFU),
NR Call forwarding no-reply(CFNR).
y=S All services,
I ISDN data(unrestricted digital),
B POTS port, phone,
M Internal modem.
ii. Deactivated by AT commands:
ATCFxy
iii. Activated by phone flash command(only forwarding phone call):
Off hook, do a flash, then dial
*20*transfer-number# for CFB,
*21*transfer-number# for CFU,
*22*transfer-number# for CFNR.
iv. Deactivated by phone flash command(phone call only):
Off hook, do a flash, then dial
#20# for CFB,
#21# for CFU,
#22# for CFNR.
v. Query the status of the call forwarding. Simply issue
ATCF?
For USA NI-1 & DMS-100 switch, we support the Call Forwarding
Variable(CFV) service. Before you invoke this feature,
you need to save the IOC(ISDN Ordering Code, feature access
code) to the TA. If you don't know about it, please ask your
phone company.
AT&ZF4=IOC_of_CALL_FORWARDING to save it, IOC=0~63.
AT&ZF? to display it.
i. Activate by AT commands:
ATCF(transfer-number)
ii. Deactivate by AT commands:
ATCF
iii. Activate by phone flash command:
Off hook, do a flash, and dial
*21*transfer-number#.
iv. Deactivate by phone flash command(phone call only):
Off hook, do a flash, and dial
#21#.
Reminder Ring: after you activate the call forwarding function,
you will hear a short ring every time a call has been forwarded.
Note 4: For USA NI-1 & DMS-100 message waiting service, the message service
is activated when you subscribe this service from your phone
company. You need to save the IOC of the message waiting
that your phone company gives you to the TA by
AT&ZF3=IOC_of_MESSAGE_WAITING(0~63)
If you have a waiting message in MSR(Message Storage and
Retrieve system) in the phone company, you will see the B1 & B2
LED blinking. Then you can retrieve you message from the MSR
system.
Once you want to deactivate this service, issue an AT command
ATMW.
Note 5: For FSK caller ID signal generation, there are two format, SMDF and
MDMF coexist. To set the format, set as below:
MDMF, set s122.6=0 ( default)
SDMF, set s122.6=1
===============================================================================
Release Note on omni.net plus Version 4.02 Jan., 14, 1998
==========================================
1.The firmware's file names for various switch type are as follows:
FILENAME SWITCH TYPE
1.1 "MP128E.402" ------ DSS1
1.2 "MP128K.402" ------ KOREA(KOREA only)
1.3 "MP128G.402" ------ 1TR6 (GERMANY only)
2.Fixed the Bugs:
=================
2.1 With country code 250 (Sweden), TA can't dial with pulse.
2.2 ATDnnn command can't accept bracket "()" in the phone number string
nnn.
2.3 Set ATS88=128 will cause TA reset.
2.4 If the answering TA response with "DISC" upon receipt of XID request,
the calling ZyXEL TA should response with UA and stop the XID
procedure and re-establish the LAP link.
2.5 Set AT&D0 and lower DTR TA can't response to any AT command.
2.6 In CAPI mode, off hook phone 2 will get busy tone no matter there is
free channel or not.
2.7 AT&T11 loop back test doesn't work.
2.8 Set DTE port 1 baud rate = 9600bps, press 't' or 'T' instead of press
'a' or 'A' as the first character then press D/V key, data terminal
will show garbage instead of OK.
2.9 Supplementary services Call Waiting/Hold/Retrieve don't work.
2.10 With SLIP, only first connection to ISP can success.
2.11 Dial with ATDIx+y where x and y are two different subscribers' phone
numbers will show connect 128K but, in fact, only one B channel
connected. (X75, V120 only)
2.12 When both calling and called sides set AT*G2, the non-password callback
function will make calls between these two parties calling back and
forth. (Both side of TAs have to upgrade F/W to fix this problem.)
2.13 For SLIP, UART hardware flow control doesn't work properly.
2.14 DTE baud rate will be changed to 1200bps after connection message
shown.
2.15 DTE baud rate will be changed to 1200bps after D/V button pressed.
2.16 TA didn't ignore the SETUP message with a CR value that is using.
2.17 S register #5 doesn't work.
2.18 Call back failed duo to switch send DISCONNECT message faster than
call back SETUP message. (Now call back SETUP message will be sent out
S64 seconds later after DISCONNECT message is sent. Users can correct
this problem by setting proper value to S64. The default value is 5
seconds. When S64 equals 0, 5 seconds timer used.)
2.19 Set improper country code (smaller than 217) will cause TA load
incorrect RING frequency and cadence.
2.20 While InterCom, if phone 1 or phone 2 pressing FLASH/5 to reject the
incoming call, both incoming connection and InterCom will be dis-
connected simultaneously.
2.21 While 3-way conference (2 local and 1 external) going, when the
external user disconnect, both local users will hear busy tone.
2.22 While phone 1 is connecting and phone 2 is ringing, sometimes phone 1
can hear ringing noise coming from phone 2.
2.23 Issue ATC$ starting EPA, if XID frame sent by ELSA TA was included,
TA will hang.
2.24 Sometimes phone 1 and phone 2 will interfer each other, especially
when one of them is a modem call.
2.25 PPP Term-Ack is blocked by our TA. Some application, e.g. WinNT
callback, will get problem.
2.26 When TA received "ATD12345;" should ignore the ending ';'.
2.27 Response to "AT#21#" is incorrect.
2.28 AT*C1~C3 should response with "ERROR".
2.29 Some people testing TA and RVS-COM Lite Ver 1.22 reported that
sometimes there are problems when sending fax.
2.30 Let s0>=3, sometimes TA disconnects before beginning answering call.
3.Newly implemented features
============================
3.1 Ringer frequency:
Ringer frequency and cadence will automatically adapt to that
country's SPEC when country code is changed.
Note:
1. Only when country code is changed ringer cadence is changed.
2. Ringer frequency can also be changed via ATS121 setting.
3. AT&F can't reload ringer frequency of country default; Ringer
frequency is changed only through the two methods mentioned above.
4. Because ringer frequency is kept in active user's profile, user
should save ringer frequency to a proper profile after ringer
frequency is changed.
3.2 Keypad protocol for DSS1 version:
Presently, the following countries support this function:
250 Sweden
238 Taiwan
236 Italy
3.3 Release D channel Layer 2 Link:
When S121.4 is cleared (=0, the default setting), if all DTE port(s)
and PHONE device(s) are idle for more than 10 seconds, TA will
actively send "DISC" to release D channel layer 2 link if layer 2 link
is still engaged. (Note that this feature is available only on DSS1
version.)
3.4 Software and Hardware reset:
Add software and hardware reset AT commands.
ATSWR:
Software reset. After this AT command issued TA restarts
system.
ATHWR:
Hardware reset. After this AT command issued TA will clear
NVRAM, load factory default S parameters, and restart system.
Note:
These two AT commands are protected by key S38.2=1. You have
to set S38.2=1 before issuing these two AT commands.
3.5 Debug Mode:
Supporting Debug Mode.
Method to enter Debug Mode:
pressing D/V button for 10 seconds after power on. Don't be
confused by pressing D/V button during power on process. Doing
that may cause TA doing Hardware Reset. When B1/B2/AA LEDs are
beginning to flash release D/V button. Now TA entering
autobauding state. Connect TA to any asynchronous terminal and
key in "AT". If TA successfully detect "AT", it will send BELL
character three times and show Debug Mode Help Menu.
What to use in Debug Mode:
In Debug Mode, there supports 6 AT commands:
ATRnnnnnn:
Read 256 bytes memory contents starting from "nnnnnn".
ATDNXfromaddr,lenght:
Download "length" bytes memory contents in X modem
starting from "fromaddr". The number is in
hexidecimal.
ATDNXP:
Download PPP DbgBuffer in X modem.
ATDNX$:
Download MonBuf (EPA buffer) in X modem.
ATSWR:
Software reset. System restarted.
ATHWR:
Hardware reset. Clear up contents of EEPROM, load
factory default and restart system.
ATWW[B]addr=hex value:
Write memory address "addr" with the specified hex
value. (Note that this is for internal use only.)
3.6 AT&V:
Add DTE rate, data length, number of stop bit, and parity information
for AT&V.
3.7 ATC$1:
ATC$1 will stop logging and start to output the tracelog buffer
WITHOUT user's intervention.
4.Known bugs
============
4.1 CAPI:
4.1.1 Don't support T.30.
4.2 E71 mode:
While DTE speed slower than 38400bps, E71 mode auto-detection is
possible only when AT commands are typing in upper case.
=============================================================================
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.