README.TXT Driver File Contents (tm240250112.exe)

=================================================================


        Wistron BIOS Reflash Disk Readme File                                   
             Version  V1.12 , September 05, 2003                       
   New Technology Development Dept. Platform Software Div.      
  Copyright (C) Wistron Incorported 2003. All rights reserved.                                                           ?
                                                       
                                                       
=================================================================

I. INTRODUCTION

    This utility is designed to perform BIOS reflashing
    to an upper version for Yuhina system :

II. PREPARING A BOOTABLE BIOS REFLASH DISK AND USE IT

    There may be two types of source you will get:

    .A ZIP package file, or
    .A source disk with uncompressed files

   Step 1. Create a bootable disk.

   Step 2. Copy the following files to that bootable disk.

        .ANSI.SYS
        (You can find this file in \windows\command or \windows)

        General Syntax:
    
        copy [source path] [destination path]

        1. copy ansi.sys a:\
        
   Step 3. Decompress the ZIP file to this bootable disk if you get a ZIP
           package,or copy all the files to the bootable disk if you get a
           source disk.

   Step 4. Put the bootable disk into Falcon series mobile, then boot.

III. USING THE Wistron Yuhina BIOS REFLASH DISK

   # NOTICE !! Important !!                                            #
   #    " Do not power off during a BIOS update. Otherwise your system #
   #      may be damaged "                                             #

   A. After Booting, You will see the massage like this (BIOS Version
      may be different):

               Wistron Yuhina
               BIOS Flash Service Diskette
               BIOS Version V1.12

               Licensed Material - Property of Wistron
               (C) Copyright Wistron Corp. 2003
               All Rights Reserved.



        This utility updates the system program to the current level.

        Press <1> to continue, <0> to exit.

        >>>>>>>>>>>>>>>>>>>>>> Important <<<<<<<<<<<<<<<<<<<<<<
        Do not power off during a BIOS update. Otherwise your system may
        be damaged.

   B. If you are ready to reflash BIOS, press "1", Otherwise press "0".
      If you press "1", the reflash utility will check if this machine
      is Wistron Yuhina series. If yes, You will see this massage:

            Wistron Yuhina
            BIOS Flash Service Diskette








       >> Warning <<
       Continuing with this process will install downlevel system
       program than currently installed in the system.
       If unsure, do not continue.

       Press <1> to continue, <0> to exit."

   C. Press "1" to make sure again. The BIOS reflash utility will
      re-check your system and begin to update your BIOS to version
      1.12

   D. If the BIOS reflash is done successful, you will see:

            Wistron Yuhina
            BIOS Flash Service Diskette



       System BIOS has been updated successfully.
       Remove your service Diskette from Disk Drive.
       Turn off the power and restart the system.

   E. Turn off power by power button, (not Ctl+Alt+Del) and next
      power on will be booting at BIOS version 1.12.

IV.Error massages:

    A. HardWare Error

                 Wistron Yuhina
                 BIOS Flash Service Diskette


                 >> Error <<
                 A hardware error occurred.

    B. BIOS Update Program Error

                 Wistron Yuhina
                 BIOS Flash Service Diskette


                 System BIOS update program has been cancelled.
                 Turn off the power and restart the system.

    C. System Error

                 Wistron Yuhina
                 BIOS Flash Service Diskette


                 >> Error <<
                 This diskette does not support this system.

Download Driver Pack

How To Update Drivers Manually

After your driver has been downloaded, follow these simple steps to install it.

  • Expand the archive file (if the download file is in zip or rar format).

  • If the expanded file has an .exe extension, double click it and follow the installation instructions.

  • Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.

  • Find the device and model you want to update in the device list.

  • Double-click on it to open the Properties dialog box.

  • From the Properties dialog box, select the Driver tab.

  • Click the Update Driver button, then follow the instructions.

Very important: You must reboot your system to ensure that any driver updates have taken effect.

For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.

server: web4, load: 1.95