Mouse User's Manual
1994 Copyright All Rights Reserved
FCC Statement on CLASS B
Note: This equipment has been tested and found to comply with the limits for
a CLASS B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
when the equipment is operated in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and if not installed
and used in accordance with the instruction manual may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. if this
equipment does cause interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
* Reorient or relocate the receiving antenna.
* Increase the separation between the equipment and receiver.
* Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
* Consult the dealer or an experienced radio TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) this device may not cause harmful interference.
(2) this device must accept any interference received, including
interference that may cause undesired operation.
1. Hardware Installation
1-1.Installing a Serial Mouse
You must have a PC fitted with a Serial/Mouse/Bus port in order to install
the mouse. Plug your mouse into the Serial/Mouse/Bus port depending on the
type of mouse.
1-2.Installing a Mouse with Mouse Port (PS/2) Connector
If you have a mouse with a round mouse port connector, you must turn off the
computer before connecting or disconnecting your mouse.
1. Turn the computer off.
2. Locate an available 6-pin round port on your computer.
3. Insert the mouse connector into the round mouse port.
4. Start your computer.
1-3.Installing a Bus Interface Board and Bus Mouse
If you have a bus mouse, you need to install the bus interface board into
your computer. Next you will need to connect the mouse to the bus port.
The Bus Interface Board Jumpers
The J1 J2 J3 J4 jumper controls interrupts in your system. Interrupt are
temporary breaks in the sequence of a program caused by various I/O devices,
such as keyboard, drawing devices, and printers. Generally, two devices
connected to the same computer cannot use the same interrupt. You must
specify a mouse interrupt that does not interfere with the other devices
connected to your computer.
The jumper refer to interrupts in the system (IRQs).If you should change the
jumper. Cross out the positions you cannot use due to the type or configura-
tion of your system. Then place the removable plastic hood on any position.
The default setting is IRQ5.
2. Hard Disk Installation
1. Insert the mouse driver diskette in Drive A (or B). Type the following:
A: <Return>
2. On the diskette are files required for the correct installation of the
software. Type the following :
INSTALL <Return>
Follow the on-screen instructions properly.
3. Driver Software Options
The mouse driver has several software options. To see these detailed options
on the screen by typing :
mouse / ?
4. Switching Mouse Mode
4-1. Switching Mouse Hareware Modes (Use mode switch)
The Serial Mouse is capable of operating either as a Microsoft Serial Mouse
or a Mouse Systems Mouse.At the base of the Mouse you will find a slide
switch. The switch has two possible positions, 'MS' and 'PC' When the switch
is set to the 'MS' position the Mouse will emulate a two-buttoned Microsoft
Mouse while setting the switch to the 'PC' position will cause the Mouse to
emulate a three-buttoned Mouse Systems Mouse.
4-2. Switching Mouse Hardware Modes (None mode switch)
As mentioned earlier, the serial mouse is capable of operating either as a
Microsoft Serial Mouse or a Mouse Systems Mouse.Which of the two modes the
mouse will operate in is determined on the power-on initiation. If any one of
the three buttons is depressed during power-on initiation, the mouse will
emulate Mouse Systems Mouse.While none of the buttons is depressed during
power-on initiation the mouse will emulate Microsoft Mouse .
4-3. Microsoft Mode
When the mouse is in Microsoft mode, only the left and right buttons are
active, while the middle button is ignored. In this mode, your mouse will
correctly emulate a Microsoft Serial Mouse.
4-4. Mouse Systems Mode
If you are a user of AUTOCAD or any other software which gives enhanced
performance with a Mouse Systems Mouse you should choose this emulation. A
Mouse Systems Mouse operates with all three buttons.
5. Un-installing the Mouse Driver
This is done by typing in the following command:
mouse /0
from the DOS prompt.
6. Driver for Windows 3.1
6-1. For Windows 3.1:
This disk contains two Windows 3.1 mouse drivers: MOUSE1.DRV and
MOUSE2.DRV. Use the MOUSE1.DRV if mouse is on the COM1 port.
Use the MOUSE2.DRV if the mouse is on the COM2 port.
The "\Win31" directory on this disk contains two Windows 3.1 mouse
drivers: MOUSE1.DRV and MOUSE2.DRV. Run the Windows 3.1 setup
program. After you choose the "Other Mouse" item, type path
"A:\Win31" or "B:\Win31". Select item 1 "Mouse on Serial port 1,
PS/2 Mouse Port" if the mouse is on the COM1 port. Select item 2
"Mouse on Serial Port 2" if the mouse is on the COM2 port.
7-2.--- Mouse driver for Windows 95 ----
=====(lastest modification Jan,3,1996 )=====
--- Setup readme ---
=============================================
(C) Copyright Chic Technology Corp.
All Rights Reserved.
7-1.Driver Support:
Serial mouse
Bus mouse
PS/2 mouse
PnP mouse(designed for windows 95)
7-2.Setup method:
7-2-1.============== Using Plug & Play mouse ============
Setup Procedure:
1).Running Windows 95 with Plug & Play computer system.
2).Plug mouse into computer.
3).Restart your computer by windows 95 shut down funtion.
4).Windows 95 will detect a PnP mouse device,
then it will show the messages below :
New Hardware Found:
[1] Driver from disk provided by hardware manufacturer.
[2] Do not install a driver [Windows will not prompt you again].
[3] Select from a list of alternate drivers.
5).Insert driver diskette into floppy disk.
6).Select [1] and tell windows 95 where driver is .
example :
You can type path "A:\Win95" or "B:\Win95".
7).You can choose what kind mouse you have choose what kind mouse
you have.
Select mouse type:
[1] Serial mouse.
[2] Bus mouse.
[3] PS/2 mouse.
8). After choosing the mouse you have ,driver will be installed,
then you should restart your computer .
7-2-2.============= Using non-PnP mouse ============
Setup Procedure:
1). Running Windows 95.
2). Plug mouse into computer.
3). Select "My computer" icon on desk.
4). Select "Control Panel" icon.
5). Select "Mouse" icon.
6). Select "General" item.
7). Click the "Change".
8). Click the "Have Disk" item ,instert driver diskette into floppy disk.
9). After you choose the "Have Disk" , type path "A:\Win95" or
"B:\Win95",and then click "Ok".
9). Select mouse type:
[1] Serial mouse.
[2] Bus mouse.
[3] PS/2 mouse.
10). Click the "Close".
11). Driver will be installed and you should restart your computer.
====Windows 95 driver readme END===
8. Trouble Shooting
Symptom 1 : No mouse movement.
Solution : - Make sure the software that you are using
supports a mouse.
- Check that mouse is plugged into serial port
at the back of computer.
- Ensure that mouse driver is installed into memory.
Symptom 2 : The cursor on the screen remains at one spot or moves
erratically.
Solution : Check the mouse cable for any breaks or sharp twists. Examine
the cable closely where it connects to the mouse.
Symptom 3 : The cursor movement stops at a corner and no longer responds
to the mouse movement.
Solution : Run the mouse driver to check which mode the mouse is operating
in.
Symptom 4 : Mouse movement does not produce corresponding cursor movement
or there is a brief pause during movement.
Solution : Clean the silicon rubber-coated ball and rollers.
Symptom 5 : After had selected mouse type for Windows 95 ,the mouse
would be disable when you clicked "OK" .
Solution : Using keyboard to close the current window and wait for
Windows 95 to give any instruction to restart your computer.
After restart Windows 95 the mouse will work normally.
-----------------------------------------------------------------------------
Muis Qebuiksaanwijzing
1.INSTALLATIE
1.1 Hardware Installatie
Om de muis te installeren moet uw pc een seri‰ele poort vrij hebben. Steek
de plug van de muis hier in.
Als u een PS/2 muis heeft aangeschaft kan deze alleen op de betreffende
PS/2 ingang worden aangesloten.
1.2 Installatie op de Harde Schijf (HDD)
Zet uw computer aan.
Type na de C: prompt: "CD\" gevold door een return, zodat het zeker is dat
u in de root terecht komt.
1.3 Het instelen van de mouse driver software
Ga voor het instellen van de gevoeligheid etc. naar de root van C: en type:
"Mouse/?" gevold door een return. Hierna hoeft u alleen de aanwijzingen op
het scherm te volgen.
1.4 Installatie van de hardware mode
U kunt de muis instellen voor gebruik als seri‰ele muis of als Microsoft
muis Miervoor kunt u het schakelaartje gebruiken dat onder op de muis zit.
En de stand waarbij "MS"zichtbaar is werkt de muis als Microsoft muis.
Nu werken alleen de linker-en rechterknop.
De middelste knop is niet aangesloten.
Dit is ook de stand die u kunt gebruiken voor het besturen van Windows
progdriver rammans. Gebruik hiervoor de eigen instellingen van Windows,
en kies de Ms Is "PC" zichtbaar dan werkt de muis als pc muis,en werken
alle drie de knoppin. Dit is voornamelijk nodig bij intensieve programma's
als Autocad e.d waar de middelste knop nodig is voor het besturen van het
programma.
** All genoemde merken zijn eigendom van hun respectievelijke eigenaren.
-----------------------------------------------------------------------------
MANUALE D'USO DEL MOUSE
1.INSTALLAZIONE
1.1 Installazione Hardware
Per poter installare il mouse, il vostro PC deve avere una porta seriale.
Inserire il connettore del mouse nella porta seriale del vostro PC. Se avete
acquistato un mouse per PS/2, inserire il connettore nell'apposita porta
mouse.
1.2 Installazione sul disco fisso
1. Accendete il vostro computer. All' apparire del prompt C:, eseguire il
seguente comando.
CD\ <Return>
2. Inserire il disco del mouse nell'unita' A. Eseguire il seguente comando:
A: <Return>
3. Nel dischetto ci sono dei file che vengono richiesti per la corretta
installazione del software. Eseguire il seguente comando:
INSTALL <Return>
A questo punto seguire attentamente le istruzioni.
1.3 Impostazione delle opzioni del Driver del Mouse
Le opzioni sono le seguenti:
Mouse/? <Return>
1.4 Come selezionare le modalita' hardware del mouse
Come detto sopra, il mouse seriale e'configurabile sia come Mouse Microsoft
sia come Mouse System Mouse. Nella parte inferiore del mouse vi e' un
commutatore che consente la selezione tra le modalita' a 2 o 3 pulsanti.
Per configurare il mouse come Mouse Microsoft (2 pulsanti) occorre spostare
il commutatore nella posizione etichettata "MS". Per configurare il mouse
come Mouse System Mouse (3 pulsanti occorre invece spostare il commutatore
nella posizione etichettata "PC".
1.5 Configurazione Microsoft
Quando il mouse e' configurato come Mouse Microsoft, solo i tasti a destra e
a sinistra funzionano, mentre il tasto al centro e' inattivo. In questo
modo il vostro mouse lavorera' correttamente come Microsoft Serial Mouse.
1.6 Configurazione Mouse System Mouse
Se siete utenti AUTOCAD dovete scegliere la configurazione Mouse System
Mouse. In questa configurazione il mouse opera con tutti e tre i tasti.
** Tutti i nomi del prodotti menzionati sono Marchi Registrati.
-----------------------------------------------------------------------------
SOURIS Guide d'utilisation
1.1 Installation de la souris
Note: pour que vous puissiez installer la souris, votre PC doit posseder un
port serie pour souris. Connectez votre souris au port serie. Si vous avez
chosi une souris PS/2,
1.2 Installation sur disque dur
1. Allumez votre ordinateur. Assurez vous que vous ˆtes dans le repertoire
principal en tapant:
CD\: <Retour>
2. Inserez la disquette MOUSE DRIVER dans le lecteur A, puis tapez:
A: <Retour>
3. La disquette MOUSE DRIVER comporte les fichiers necessaires …
l'installation du log- iciel. Tapez:
INSTALL <Retour>
Suivez attentivementles instruction affich‚es a l'‚cran.
1.3 Installation de la disquette
Avant de commence, assurez vous que votre disquette format‚e est prˆt.
1. Verifiez que la lecteur de disquette en cours est A:
2. Inserez la disquette MOUSE DRIVER en A:
3. Inserez la disquette format‚e en B:
4. Tapez:
Install <Retour>
Suivez attentivement les instructions affich‚es a l'‚cran. Le programe
installe les fichiers sur votre disquette.
1.4 Configuration du programe de controle
Pour les options du programe MOUSE DRIVER, tapez:
C:MOUSE/?<Retour>
Vous avez maintenant acces aux differentes options affich‚es a l'‚cran.
1.5 Commutateur de mode
La souris serie fonctionne aussi bien en mode MICROSOFT serie, qu'en mode
MOUSE SYSTEM.
Sur le verso de la souris se trouve un commutateur. Ce commutateur comporte
2 positions; "MS" et "PC". Lorsque le commutateur est positionn‚ sur "MS",
la souris est mulee en souris MICROSOFT - 2 boutons; le commutateur en
position "PC" la souris est emul‚e en souris MOUSE SYSTEM - 3 boutons.
1.6 Mode Microsoft
Lorsque ce mode est commut‚, seuls les boutons de gauche et de droit ont
actifs, le uton du milieu ‚tant quant a lui innactif. Sous ce mode,
votre souris est correctement emul‚e MICROSOFT serie.
1.7 Mode MOUSE SYSTEM
Si vous ˆtes utilisateur d'AUTOCAD ou tout autre logiciel permettant de
meilleurs performances avec le MOUSE SYSTEM, vous devez choisir cette
emulation. Le MOUSE SYSTEM, fonctionne avec les 3 boutons.
** Toutes les marques cit‚es sont des marques depos‚es par leurs proprietaire
resectif.
-----------------------------------------------------------------------------
Maus Bedienungsanleitung
1.Installation
1.1 AnschluB der Maus
Um die Maus anschlieBen zu k"nnen, ben"tigen Sie einen PC mit einer
seriellen MausSchnittstelle. SchlieBen Sie die Maus an der seriellen
Schnittstelle an. Haben Sie eine PS/2- Maus gekauft, so schlieBen Sie
sie am PS/2-AnschluB an.
1.2 Installation auf Festplatte
1. Schalten Sie den Computer an. Wenn die DOS-Eingabeaufforderung C:
erscheint ,geben Sie das Folgende ein:
CD\ <Return>
2. Legen Sie den Maustreiber in Laufwerk A ein. Geben Sie das Folgende ein:
A: <Return>
3. Auf der Diskette sind Dateien, die fr die korrekte Installation der
Software erforderlich sind. Geben Sie das Folgende ein:
INSTALL <Return>
Folgen Sie genau den Anweisungen auf dem Bildschirm.
1.3 Treiber-Software-Optionen
Die Optionen des Maustreiber-Programm sind wie folgt:
mouse/? <RETURN>
Die einzelnen Auswahl-Befehle sehen Sie dann auf dem Bildschirm.
1.4 Auswahl der Betriebart
Die serielle Maus kann entweder als MICROSOFT serielle Maus oder als MOUSE
SYSTEM-Maus betrieben zu werden. Auf der Unterseite der Maus finden Sie
einen Schalter mit zwei m"glichen Stellungen: "MS" und "PC". Wenn der
Schalter auf der "MS"- Position, steht, wird die Maus als 2-Tasten
MICROSOFT-Maus Konf iguriert, steht der Schalter auf der "PC" - Position,
wird die Maus als 3-Tasten MOUSE SYSTEM-Maus konfiguriert.
1.5 MICROSFT Modus
Wenn die Maus im MICROSOFT Modus betrieben wird, sind nur die rechte und die
linke Taste aktiv, w„hrend die mittlere Taste ohne Funktion ist. In diesem
Modus wird die Maus wie eine originale MICROSOFT serielle Maus konfiguriert.
1.6 MOUSE SYSTEM Modus
Wenn Sie Anwender von AUTOCAD oder anderen Software sind, die verbesserte
Leistngen mit einer MOUSE SYSTEM-Maus erm"glichen, sollten Sie diesen Modus
w„hlen. Eine MOUSE SYSTEM-Maus arbeited mit allen drei Tasten.
** Alle genannten Produktnamen sind eingetragene Warenzeihen ihre Hersteller.
-----------------------------------------------------------------------------
Rat¢n Manual del Usuario
1. Instalaci¢n del software del rat¢n
1.1 Instalaci¢n del controlador del rat¢n
1. Encienda el ordenador.
2. Si tienne un sistema de disco fijo, introduzca el disco del controlador
del rat¢n en la unidad A y teclee el siguietie comando en el indicator
de DOS:
CD\ <Return>
A: <Return>
INSTALL <Return>
Si tienne un sistema con dos unidades de disco flexible, introduzca el
disco del controlador del rat¢n en la unidad A y teclee el siguiente
comando en el indicador del DOS:
INSTALL B: <Return>
3. Utilizando un editor de texto (como, por ejemplo, EDLIN), introduzca el
comando:
\MOUSE
en su archivo AUTOEXEC.BAT. (Si desea m s informaci¢n acerca de los
archivos AUTOEXEX.BAT, consulte el manual del DOS).
4. Vuelva arrancar su ordenador. El software del rat¢n se cargara
automaticamente desde el disco fijo cada vez que arranque el ordinador.
1.2 Consejos para sujetar el rat¢n
Sujete el rat¢n con el pulgar y el me¤ique en cualquiera de los lado del
rat¢n. Rel jese y utilicelo con suavidad. Descanse la mu¤eca en la superficie
de la mesa para que el desplazamiento sea fluido. Coloque los dedos sobre los
botones.
1.3 Puerto de communicaciones (n)
El puerto de communicationes hace referencia a los dos puertos serie en
algunos ordenadores. El rat¢n se puede configurar para COM1 o para COM2.
El valor por defecto es COM1.
1.4 Selecci¢n del modo para de 2 o 3 botones
El rat¢n tiene un interruptor en la base para seleccionar el modo de
operaci¢n con 2 o 3 botones. Para configurar el rat¢n como un rat¢n
MICROSOFT (2 botones ), mueva el interuptor hacia la posici¢n "MS".
Para configurar el rat¢n como un rat¢n MOUSE SYSTEM (3 botones), mueva
el interuptor hacia la posici¢n "PC". Si desea cambiar el modo despu‚s
de hacer completado la instalaci¢n del soft ware, mueva el interruptor
hacia la posici¢n deseada. El rat¢n PS/2 solo se
puede instalar en un puerto de rat¢n PS/2.
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.