slimc2.ini Driver File Contents (Simplex_8420U_Slim_600_USB_scanner_driver.zip)

// Version 2.6.6


[File Settings]
LM9831=9831

[Scanner Info]
Crystal_Frequency=48000000
Optical_Resolution=600		//Optical Resolution in dpi
Motor_Steps_Per_Inch=600	//Number of fullsteps to make motor move one inch
Max_Scan_Speed=1.05	//1.25		//Maximum sensor speed in inches/s
Max_Move_Speed=1.05	//1.25		//Maximum sensor speed in inches/s
RAM_Size=512			//512,2048		reg 42 b6

Image_Pixel_Width=5100		//width of scan area in pixels
Scanner_Length=11.7		// length in inches of the scanner bed
X_Start_of_scan=140  //155		//data pixel start, in units of full optical pixels
Y_Start_of_scan=220 //170 //160  //150		//how many full steps to skip at start of scan from home position
Total_Pixels=5415	//5415	//Number of pixels in CCD reg 20:21

SS_Buf_Size_KB=16                  // buffer size for stop-start scan
SS_PauseLimit=12
SS_Delay2File=0


[SLIMC2]
// ---- use by SS_API
AutoEdgeBlack=-80  //40 positive for black board, negative for black
BkCalibMax=300
BlackCalib=0

[Scanner caps]
WarmUpTime=-10 //-45       //1200  //sec
WarmUpTimeInc=2000   //ms
WarmUpPercent=50     // = (50/100) percent 

LampFacMin=100      //100/100.
LampFacMax=115      //115/100.

PreviewDPI=50
ScanDPImax=19200
ScanDPImin=10
ScanDPIinc=1

ScanWindowLeft=0
ScanWindowTop=0
ScanWindowRight=5100
ScanWindowBottom=7016

[Scanner Can]
//CanHwTrueGray=0
CanExposure=1
CanImgChannel=1
CanPaperOn=0
CanPaperReady=0
CanPaperOut=0
CanCoverOpened=0
CanHwScaling=1
CanHwRgbAlign=0
CanSwCalibBlack=0
CanCalibEveryScan=1
CanPullingLPT=0
CanRIC=0
CanRGBCorrect=0
CanLogFile=0

CanH50=1
CanH100=1
CanH200=0
CanH400=0

[Calibration]
//Warmup_Calibration_On=1

Line_BlackCalibration_On=1
Line_WhiteCalibration_On=1
Line_BlackCalibration2_On=1      //-2000 : lamp off calib => lamp on  => wait 2000 ms

Pixel_BlackCalibration_On=2000   //3000 ms using pixel offset //-3000 using uniform offset
Pixel_WhiteCalibration_On=1

Pixel_BlackCalibration_MaxDiff=4 //32    //14-bit counts
//Pixel_BlackCalibration_MaxDiffR=4    //14-bit counts
//Pixel_BlackCalibration_MaxDiffG=4    //14-bit counts
//Pixel_BlackCalibration_MaxDiffB=4    //14-bit counts

//Pixel_WhiteCalibration_MaxDiff=5000   //divide by 1000

//Pixel_BlackCalibration_Slop=8       //
Pixel_BlackCalibration_Slop=4       //
Pixel_BlackCalibration_Offset=15 //15    //dived by 10

GammaFile_On=0    //1: file, 0: noone, -1: formula calc
RGamma=12   //gamma= 1+12/10
GGamma=12   //gamma= 1+12/10
BGamma=12   //gamma= 1+12/10
RBkLinear=20   //linear pos = 20/255
GBkLinear=20   //linear pos = 20/255
BBkLinear=20   //linear pos = 20/255


//TestShading_On=1
//TestOffset_On=-50
//TestOffset_SubWidth=5
//TestOffset_Diff=16

//USB_TransferRate=-702166
USB_TransferRate=1000000

adc_gain_target_factor=0.90   //0.85

red_target=15213
green_target=15238
blue_target=14680

;red_target=10378    
;green_target=10788  
;blue_target=11402   

Calibration_Height=60	        //Height for pixel white calibration
Calibration_Black_Height=80     //Height for pixel black calibration

ROffset=2
GOffset=2
BOffset=2

RGain=6
GGain=1
BGain=11

// -------------------------------
[Sensor Settings]
Maximum_Integration_Time_Highlamp=8  //Max IT before AFE or CCD saturates (ms)
Maximum_Integration_Time_Lowlamp=6   //8   //Max IT before AFE or CCD saturates (ms)
Minimum_Integration_Time_Lowres=6    //Min Integration Time for hdiv > 2
Minimum_Integration_Time_Highres=6   //6   //Min Integration Time hdiv <=2

Input_Polarity=Negative		//Negative or Positive	reg B b0
CDS=On				//On or Off		reg B b1
Sensor_Type=Standard		//EvenOdd or Standard	reg B b2
Line_Separation=4	    		//Distance between R, G, B sensor lines

Phi1_Polarity=Positive		//Positive or Negative	reg C b0
Phi2_Polarity=Positive		//Positive or Negative	reg C b1
RS_Polarity=Positive		//Positive or Negative	reg C b2
CP1_Polarity=Positive		//Positive or Negative	reg C b3
CP2_Polarity=Positive		//Positive or Negative	reg C b4
TR1_Polarity=Positive		//Positive or Negative	reg C b5
TR2_Polarity=Positive		//Positive or Negative	reg C b6

Phi1_Status=Active		//Active or Disabled	reg D b0
Phi2_Status=Active		//Active or Disabled	reg D b1
RS_Status=Active		//Active or Disabled	reg D b2
CP1_Status=Active	  	//Active or Disabled	reg D b3
CP2_Status=Disabled		//Active or Disabled	reg D b4
TR1_Status=Active		//Active or Disabled	reg D b5
TR2_Status=Disabled		//Active or Disabled	reg D b6
TR_Pulse=1			//1 or 2		reg D b7

TR_Pulse_Duration=3		//0 - 15		reg E b0..3
TR_PHI_Guardband_Duration=1	//0 - 15		reg E b4..7

[Pixel Rate Timing]
//Use these parameters for all pixel rate scanning
Pixl_Optical_Black_Clamp_Start=8  //9 //0 - 23		reg F b0..4
Pixl_Optical_Black_Clamp_End=23   //18	 //0 - 23		reg 10 b0..4
Pixl_Reset_Pulse_Start=4	//0 - 23		reg 11 b0..b4
Pixl_Reset_Pulse_End=7		//0 - 23		reg 12 b0..b4
;------------------------
Pixl_CP1_Pulse_Start=8		//0 - 23		reg 13 b0..b4
Pixl_CP1_Pulse_End=11		//0 - 23		reg 14 b0..b4
Pixl_CP2_Pulse_Start=0		//0 - 23		reg 15 b0..b4
Pixl_CP2_Pulse_End=0		//0 - 23		reg 16 b0..b4
Pixl_Reference_Sample=12	//0 - 23		reg 17 b0..b4
Pixl_Signal_Sample=15	  	//0 - 23		reg 18 b0..b4

[Line Rate Timing]
//Use these parameters for all line rate scanning
Line_Optical_Black_Clamp_Start=2 //0 - 7		reg F b0..4  
Line_Optical_Black_Clamp_End=7	//0 - 7			reg 10 b0..4 
Line_Reset_Pulse_Start=1  //0	//0 - 7			reg 11 b0..b4
Line_Reset_Pulse_End=2    //1		//0 - 7			reg 12 b0..b4
Line_CP1_Pulse_Start=2    //0		//0 - 7			reg 13 b0..b4
Line_CP1_Pulse_End=3      //0		//0 - 7			reg 14 b0..b4
Line_CP2_Pulse_Start=0		//0 - 7			reg 15 b0..b4
Line_CP2_Pulse_End=0		//0 - 7			reg 16 b0..b4
Line_Reference_Sample=4		//0 - 7			reg 17 b0..b4
Line_Signal_Sample=5      //0		//0 - 7			reg 18 b0..b4

[Misc Timing]
CIS_TR_Timing=Off		//Off, Mode1, or Mode2	reg b b3..4
Fake_Optical_Black_Pixels=Off	//Off or On		reg b b5

Optical_Black_Pixels_Start=15	//0-255			reg 1C
Optical_Black_Pixels_End=50	//0-255			reg 1D

Color_Mode=0			//0 = 3 Channel Pixel Rate	reg 26 b0..2
//1=3 Channel Line Rate
//2 or any others: Scanner 
//   doesn't support color
//3=1 Channel Line Rate

Gray_Channel=Green		//Red, Green or Blue 	reg 26 b3..4

[3 Channel Line Rate Settings]
TR_Red=0			//0 or 1		reg 26 b5
TR_Green=0			//0 or 1		reg 26 b6
TR_Blue=0			//0 or 1		reg 26 b7
TR_Red_Drop=0			//0-2			reg 27 b0..1
TR_Green_Drop=0			//0-2			reg 27 b2..3
TR_Blue_Drop=0			//0-2			reg 27 b4..5

[Illumination Settings]
Illumination_Mode=Mode1		//Off, Mode1, Mode2, Mode3	reg 29 b0..b1
Green_PWM_Duty_Cycle_High=0   //4095	//0-4095		reg 2A:2B
Green_PWM_Duty_Cycle_Low=0    //4095	//0-4095		reg 2A:2B
Red_Lamp_On=1			//0-16383		reg 2C:2D
Red_Lamp_Off=16383		//0-16383		reg 2E:2F
Green_Lamp_On=16383   //0			//0-16383		reg 30:31
Green_Lamp_Off=1      //0		//0-16383		reg 32:33
Blue_Lamp_On=16383    //32			//0-16383		reg 34:35
Blue_Lamp_Off=1       //48		//0-16383		reg 36:37

[Stepper Motor Settings]
Stepping=Micro			//Full or Micro		reg 45 b0
// If it's Micro, current sensing=2 phases,reg 45 b1
// If it's Full, current sensing=1 phase
Phase_A_Polarity=Positive	//Positive or Negative	reg 45 b2
Phase_B_Polarity=Positive	//Positive or Negative	reg 45 b3
Stepper_Motor_Output_Status=stepper_motor_outputs // tri-state or stepper_motor_outputs reg 45 b4
//Vertical DPI divider bits should always be 0.
Steps_to_Scan_After_PS2=0	// 0..4095		reg 4c:4d
Resume_Scan_Threshold=64
Steps_To_Reverse=48  //36 //24  //24		//0-63			reg 50
Steps_Stopped=3			//0-3			reg 51 b2..3
Steps_25=3			//0-3			reg 51 b4..5
Steps_50=3			//0-3			reg 51 b6..7
Non_Reversing_Extra_Lines=0	//0-7			reg 54 b0..2
KickStart_Steps=0		//0-7			reg 55 b0..2
Hold_Current_Timeout=2		//0-31			reg 54 b3..7
Stepper_PWM_Frequency=8		//0-255			reg 56
Stepper_PWM_Duty_Cycle=60 //23 	//0-63			reg 57
PWM_200=23

[Paper Sensor]
Home_Sensor=1			//1 or 2 - P.S. which sensor that detects home
REG_0x58=15                   //Sen2=[no,level,high]; Sen1= [yes,Edge,High]


//[Scanner Software Settings]
//Buffer_Size=16			//RAM Buffer size in k bytes
//Min_Buffer_Limit=1		// dont read scan buffer below this point in k bytes

Download Driver Pack

How To Update Drivers Manually

After your driver has been downloaded, follow these simple steps to install it.

  • Expand the archive file (if the download file is in zip or rar format).

  • If the expanded file has an .exe extension, double click it and follow the installation instructions.

  • Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.

  • Find the device and model you want to update in the device list.

  • Double-click on it to open the Properties dialog box.

  • From the Properties dialog box, select the Driver tab.

  • Click the Update Driver button, then follow the instructions.

Very important: You must reboot your system to ensure that any driver updates have taken effect.

For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.

server: web1, load: 1.22