HighPoint Web RAID Management Software (WebGUI) for Windows
Copyright (C) 2010 HighPoint Technologies, Inc. All rights reserved.
Last updated on Jun 15, 2010
HighPoint Web RAID Management Software (WebGUI) is used to monitor and configure
your hard disks and RAID arrays attached to HighPoint RAID controllers.
This file is divided into the following major sections:
1. Files Listing
2. System Requirements
3. Installing the Software Package
4. Running the Management Software
5. Rivision History
1. Files Listing
------------------
README.txt This file
confs <DIR> I2C configuration file for disk enclosure
Other files Installation package files
2. System Requirements
------------------------
The software package must be installed on system with supported HighPoint
RAID controllers installed, and the device driver must be loaded to run
the service.
A web browser with XML support is required on the client side, e.g. Internet
Explorer 6.0, Mozilla or FireFox.
3. Installing the Software Package
------------------------------------
To install the packge, run "setup.exe" on disk1.
4. Running the Management Software
------------------------------------
To run the WebGUI, start your browser and enter the following URL address:
https://localhost:7402
If you are accessing WebGUI on a remote system please change "localhost"
to the server address.
If you can't connect to local system, please check if hptsvr.exe is running on
the system. If not, you can start it manually by running "net start hptsvr"
under a Windows command prompt.
If you can't connect to a remote system, check if hptsvr is running on that
system and you can access the remote system via TCP/IP connection. If you
have firewall configured, make sure TCP port 7402 is not blocked.
5. Rivision History
---------------------
v1.5.6 06/15/2010
Add Winbond W25X20BV/W25X40BV flash support.
v1.5.5 04/06/2010
Add RR27xx controller support.
Fix dual controllers bios update issue.
Fix redundant event log when spare disk took over.
v1.5.3 11/19/2009
Support RR62x controller.
v1.5.2 10/09/2009
Fix driver parameter list overflow.
v1.5.1 09/15/2009
Add "no config" SAF-TE config option.
v1.5.0 08/14/2008
Fix a bug about 27xx updating bios.
Support updating adapter BIOS and firmware.
Fix misreporting of SAS drive status in SHI page.
v1.4.9 08/29/2008
Support 26xx driver.
Fix a bug in displaying HDD serial number.
Display verify/initialize/rebuild/ progress ,and remaining time.
Reduce event page loading time.
Support expander.
Fix a bug in rebuilding progress.
Display BIOS version.
Fix a bug about Dual controllers(3520+3220).
Rebuild starts when array member disk come back.
Support expander.
v1.4.8 02/25/2008
Add mute beeper button.
Fix a bug about OCE.
Change Spindown Idle Disk time.
Add X4-RR2314MS.conf.
Fix a bug about alarm.
Support custom event log path in windows.
Support "Continue Rebuilding on Error" feature.
Fix a bug in detecting hpt driver.
Support RAID recovery feature.
Support Array Blocksize.
Check password length.
v1.4.7 09/24/2007
Add Spindown Idle Disk(MAID) support.
Improve SHI page display.
Fix RAID10 display wrong status after unpluging a member disk during initializing.
Fix drvinst auto-exit when creating an array.
Add VSS(Variable Sector Size) support for RAID array.
Set HPT_MINIPORT_TIMEOUT 20.
v1.4.6 07/26/2007
Add X8 support.
Fix transform creation issue.
Improve event log load and display.
Update help doc.
v1.4.5 06/15/2007
Add SHI(Storage Health Inspector) function support.
Add 32 Max Members per array support(Need driver support).
v1.4.4 03/07/2007
Add Port multiplier support(please refer to driver readme.txt).
Add HDD serial number display.
v1.4.3 11/16/2006
Add sector repair logging.
Minor display fixes.
v1.4.2 10/23/2006
Add controller information display for RR3xxx adapters.
v1.4.1 09/25/2006
Add RR3xxx controller support.
v1.3 02/20/2006
Add enable/disable controller audible alarm option.
v1.2 08/03/2005
Add multi-user support.
Fix problem on arrays with more then 8 member drives.
v1.1 07/21/2005
Add support for RR18xx/RR1640/RR4x4 controllers.
v1.0 04/28/2005
First release for RR22xx
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.