***************************************************************************** * * * SURECOM EP-320X-V Fast Ethernet 10M/100M PCI Adapter * * * * Installation guide for NDIS2 Driver * * * ***************************************************************************** This file will help you with the installation for EP-320X-V in the following platform : 1. LAN Manager Workstation/Server 2. LANtastic 6.0 3. LAN Server 2.0/3.0 4. LAN Server 4.0 ( DOS LAN Services / OS2 LAN Server ) 5. Microsoft Network Client 3.0 for MS-DOS 6. Windows for Workgroups v3.10 A. sample protocol.ini =============================================================================== 1. LAN Manager Workstation/Server Setup driver procedures on LAN Manager workstation/server : ----------------------------------------------------------- Before you start with the installation process, make sure that the adapter is properly installed and configured. Make sure your Microsoft LAN Manager is properly installed. 1) Run the appropriate Microsoft Lan Manager SETUP for computer you are setting up.(DOS, OS/2 or OS/2 Server). Select "Configuration" item ,(the EP-320X-V driver isn't included on the Lan Manager disk) and insert the SURECOM EP-320X-V driver disk, specify path a:\, and select the EP-320X-V driver and follow the directions. 2) When completed, reboot your computer. Sample Configuration Files: --------------------------- CONFIG.SYS (for DOS will contain): DEVICE=C:\LANMAN.DOS\DRIVERS\PROTMAN\PROTMAN.DOS /I:C:\LANMAN.DOS DEVICE=C:\LANMAN.DOS\DRIVERS\ETHERNET\FETND\FETND.DOS CONFIG.SYS (for OS/2 will contain): DEVICE=C:\LANMAN.OS2\DRIVERS\PROTMAN\PROTMAN.OS2 /I:C:\LANMAN.OS2 DEVICE=C:\LANMAN.OS2\DRIVERS\ETHERNET\FETND\FETND.OS2 PROTOCOL.INI (refer to line no.579 in this file): =============================================================================== 2. LANtastic 6.0 1) Run Lantastic 6.0 install program and follow screen instructions. 2) When the "Network Adapter Setup" appears, Select "Use NDIS driver for non-Artisoft adapter" and type "A:\NDIS2" in the search path and select "Search" button. 3) When the install program find FETND NDIS driver, select "OK" to continue. 4) Follow the screen instructions to complete the installation. 5) Restart the computer. Manual install for Lantastic 6.0/5.0 ------------------------------------ You can replace the NDIS driver by modify the following configuration files: 1) Sample CONFIG.SYS ----------------- DEVICE=C:\LANTASTI\PROTMAN.DOS /I:C:\LANTASTI DEVICE=C:\LANTASTI\FETND.DOS 2) Sample STARTNET.BAT ------------------- C:\LANTASTI\AI-NDIS BIND_TO=FETND_NIF C:\LANTASTI\AILANBIO 3) Sample PROTOCOL.INI ( see "A. Sample protocol.ini" ) =============================================================================== 3. LAN Server 2.0/3.0 Installing driver procedure on DOS LAN Requester : -------------------------------------------------- 1) Insert the IBM LAN Support Program (LSP) Version 1.30 (or 1.31) Diskette into your floppy drive A: . 2) Type A:\dxmaid and press <Enter> . 3) The screen will display the IBM logo. Press <Enter> twice until the "Environment Information" appears on screen. 4) Responds to the screen prompts, specifying the following values for each field,use the <Space Bar> to toggle between choices: Configuration for this computer? Yes Use existing configuration information? Yes Do you have adapter option diskettes? Yes Are you configuring for two adapters? No Do you need 802.2 interface support? Yes Source for LSP A:\ Target for new configuration C:\LSP Make sure that the values given above are correct, then press <Enter> to store your choices. 5) Insert the SURECOM EP-320X-V driver diskette in floppy A,and specify your pathname A:\NDIS2 then press ENTER. 6) Follow screen instructions to complete the process. Simply pressing <Enter> for each screen display will select the default options. Press <Enter> until you reach the display prompting you to insert the LSP diskette. 7) Insert the LSP diskette as prompted. Press <Enter> to acknowledge completion of the action. 8) A screen showing the current configuration detected will be displayed. It should show the SURECOM EP-320X-V Adapter and the protocols already selected (i.e., "IBM IEEE 802.2" and "IBM OS/2 NETBIOS"). 9) Press <F4>. to save the new configuration. This completes the LSP installation. 10) Save the configuration and reboot your computer. 11) Insert the DOS LAN Requester Install Diskette 1 into your floppy drive. 12) Type A:\INSTALL <Enter> 13) The IBM logo will again appear on the screen. Press <Enter> to move on to the next screen. 14) Follow screen instructions, pressing <Enter> to move from screen-to-screen until you are prompted to indicate the pathname of the DOS LAN Requester directory (C:\DOSLAN ). 15) Specify the pathname (C:\DOSLAN is the default) for the DOS LAN Requester directory . Then press <Enter> to continue. 16) The program will ask you for the services that you require. 17) Highlight the appropriate option. Select either "Send messages" or "Send, View, Edit, and Log message" option. (Normally, second option "Send, View, Edit and Log message" is selected). 18) Specify the PC's ID and domain ID. 19) Follow screen prompts to complete the installation. Installing driver procedure on OS/2 LAN Server 2.0/3.0 : ------------------------------------------------------ Before you start with the installation process, make sure that OS/2 LAN Server is properly installed. Similarly, your adapter should also be properly installed in your server. 1) Copy FETND.OS2 and FETND.NIF files from your Driver diskette (\NDIS2) to C:\IBMCOM\MACS. 2) Click the OS/2 LAN Service icon. 3) Select "Installation and configuration". The IBM logo should appear onscreen. 4) Click <OK>. 5) Select <Advance> and press <Enter>. 6) Select "Install or Configuration this Workstation." 7) Select server type, adding a server or domain controller. The "install or remove" selections should appear. 8) Select "Configure a component." 9) Click the "Configure" button. 10) Select "Configure workstation." 11) Select "SURECOM EP-320X-V Fast Ethernet Adapter" when prompted to identify you Network Adapter. Then click the <Add> button. 12) Select IBM NETBIOS from the list and click the <Add> button. 13) Select <OK> to confirm all selections. 14) Follow screen instructions to complete the process, selecting <OK> to accept default selections. 15) Continue pressing <OK> until your screen prompts you to backup old CONFIG.SYS and AUTOEXEC.BAT and create a new CONFIG.SYS and AUTOEXEC.BAT. Also select <OK> to confirm this. 16) Installation is complete now. Reset your PC by turning it off and on. Note: ----- 1) The DOS version must be bellow DOS 5.0 when install DOS LAN requester into your system. 2) sample protocol.ini ( see "A. Sample protocol.ini" ) =============================================================================== 4. LAN Server 4.0 ( DOS LAN Services / OS2 LAN Server ) Installing driver procedure on DOS LAN Requester : -------------------------------------------------- Before you start with the installation process, make sure that DOS LAN Services is properly installed. Similarly, your adapter should also be properly installed in your client PC. 1) Copy FETND.DOS from your Driver diskette (A:\NDIS2) to DOS LAN Services subdirectory C:\DLS . 2) Under DOS LAN Requester subdirectory C:\DLS, run INSTALL 3) The screen display some description. If it's correct, move highlight to "The listed options are correct" item ,then press ENTER. 4) Move highlight to "Network Card", then press ENTER. 5) Select "Change driver for network card." item, then press ENTER. 6) Select "Network card not shown in list below..", then press ENTER. 7) Insert the SURECOM EP-320X-V driver diskette in floppy A,and specify your pathname A:\NDIS2,then press ENTER. 8) SURECOM EP-320X-V driver is now installed on your computer, reboot your computer. Installing driver procedure on OS/2 LAN Server 4.0: --------------------------------------------------- Before you start with the installation process, make sure that OS/2 LAN Server is properly installed. Similarly, your adapter should also be properly installed in your server. 1) In OS/2 window, Click the "MPTS" icon. 2) The screen will display the IBM Log, press "OK". 3) Select "Install" button. 4) Insert the SURECOM EP-320X-V driver diskette, specify the driver path A:\NDIS2 and press <Enter>. 5) When complete above step to load FETND.OS2 into OS/2 system, then configure your system. 6) The same step as step 3, select "Configure" button. 7) The screen will display "Configure" dialog box and select "LAN adapters and protocols" then press "configure" button. 8) The screen will display "LAPS Configuration" dialog box, move highlight to "SURECOM EP-320X-V Fast Ethernet Adapter" item in "Network Adapter" window, and select "NetBios" protocol. Press "OK". 9) Installation is complete now. Reset your PC by turning it off and on. Installing Multiple LAN Adapters: ---------------------------------- 1)follow [3]. 1-9 and add two EP-320X-V Adapters driver 2)in IBM Lan Services icon, OS/2 Lan Sercices Installation /Configuration Select your the server of the insatlled,[OK]. Do you want to re-install this version.[No]. Installing tow card driver [OK] in mpts. Configure a component. [OK] Lan Services Adapters. [OK] Configure. [OK] Two Adapter [V]. OK sample PROTOCOL.INI ( See "A. Sample protocol.ini" ) =============================================================================== 5. Microsoft Network Client 3.0 for MS-DOS Installation Procedure : ---------------------- 1) Change to the Microsoft Network Client subdirectory, and run SETUP.EXE 2) The screen will display some infomation. Press <Enter> . 3) Responds to the screen prompts, selecting "Change Network Configuration",then press <Enter>. 4) Move the highlight to "Add Adapter", press <Enter>. 5) Select "Network adapter not shown on list below ...". 6) Insert the SURECOM EP-320X-V driver diskette in floppy A,and specify your pathname A:\NDIS2,then press <Enter>. 7) Follow screen instructions to complete the process. Simply pressing <Enter> for each screen display will select the default options. Press <Enter> until you reach the display prompting you to reboot your system. =============================================================================== 6. Windows for Workgroups v3.10 Setup Procedure: ---------------- 1) Start the Windows for Workgroup 3.1. 2) Click the "Control Panel" icon in the Program Manager Window. 3) Click the "Network" icon in the Network Window. 4) When the "Network Settings" dialog box appears, select "Adapters" button. 5) Select "Add" icon from the "Network Adapters" dialog box. 6) Select "Unlisted or Updated Network Adapter". 7) When the "Install Driver" window appears, insert the distribution diskette into drive A:, type "A:\NDIS2" and press <Enter>. 8) Press <Enter> to select "SURECOM EP-320X-V Fast Ethernet Adapter". 9) Click "Setup..." to popup the setup window. 10) Click "Advanced..." if you want to modify the advanced features. Please refer to the next section for the description of the keywords. 11) Close each windows and restart the computer. =============================================================================== A. Sample protocol.ini [FETND_NIF] DRIVERNAME = FETND$ AUTO = 1 or 0 ; Enable Auto Negotiation SPEED = 10 or 100 ; Set line speed = 10 or 100 Mbps FULLDUPLEX = 0 or 1 ; Set to FullDuplex or HalfDuplex SLOT = 1 ; Set physical slot of adapter,Useful for 2 adapters. ... NOTE: FULLDUPLEX and SPEED should be used together. -------------------------------- End Of File ---------------------------------Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.