[Identification] OptionType = NetAdapter [PlatformsSupported] PCI ISA EISA "Jazz-Internal Bus" [Options] ETH16I ETH32 [IRQChoicesETH16I] IRQ_1 = "AUTO",255 IRQ_2 = "5",5 IRQ_3 = "9",9 IRQ_4 = "10",10 IRQ_5 = "15",15 [IRQChoicesETH32] IRQ_1 = "AUTO",255 IRQ_2 = "3",3 IRQ_3 = "5",5 IRQ_4 = "7",7 IRQ_5 = "9",9 IRQ_6 = "10",10 IRQ_7 = "11",11 IRQ_8 = "12",12 IRQ_9 = "15",15 [IOBaseAddrChoicesETH16I] IOBase_1 = "AUTO",0 IOBase_2 = "0x240",576 IOBase_3 = "0x260",608 IOBase_4 = "0x280",640 IOBase_5 = "0x2A0",672 IOBase_6 = "0x300",768 IOBase_7 = "0x340",832 IOBase_8 = "0x380",896 [IOBaseAddrChoicesETH32] IOBase_1 = "AUTO",0 IOBase_2 = "0x1000 Slot 1",4096 IOBase_3 = "0x2000 Slot 2",8192 IOBase_4 = "0x3000 Slot 3",12288 IOBase_5 = "0x4000 Slot 4",16384 IOBase_6 = "0x5000 Slot 5",20480 IOBase_7 = "0x6000 Slot 6",24576 IOBase_8 = "0x7000 Slot 7",28672 IOBase_9 = "0x8000 Slot 8",32768 [TransceiverChoicesETH16I] Txcv_1 = "BNC","Bnc" Txcv_2 = "AUI","Aui" Txcv_3 = "TP","Tp" Txcv_4 = "AUTO","Auto" Txcv_5 = "SETUP","Setup" [TransceiverChoicesETH32] Txcv_1 = "BNC","Bnc" Txcv_2 = "AUI","Aui" Txcv_3 = "TP","Tp" Txcv_4 = "AUTO","Auto" Txcv_5 = "SETUP","Setup" [FileConstants] UtilityInf = "UTILITY.INF" subroutineinf = "SUBROUTN.INF" SoftwareType = "driver" Exit_Code = 0 NetEventDLL = "%SystemRoot%\System32\netevent.dll" IoLogMsgDLL = "%SystemRoot%\System32\IoLogMsg.dll" Manufacturer = "ICL" ProductMajorVersion = "1" ProductMinorVersion = "1" ProductVersion = $(ProductMajorVersion)"."$(ProductMinorVersion) ProductSoftwareName = "ETH16I" ProductSoftwareImagePath = "\SystemRoot\System32\drivers\eth16i.sys" NetRuleSoftwareType = "eth16iSys ndisDriver eth16iDriver" NetRuleSoftwareUse = $(SoftwareType) NetRuleSoftwareBindForm = """Eth16iSys"" yes no container" NetRuleSoftwareClass = {"eth16iDriver basic"} NetRuleSoftwareBindable = {"eth16iDriver eth16iAdapter non exclusive 100"} ProductHardwareName = "ETH16I" NetRuleHardwareType = "eth16i eth16iAdapter" NetRuleHardwareBindForm = " yes yes container" NetRuleHardwareClass = {"eth16iAdapter basic"} ProductKeyName = $(!NTN_SoftwareBase)"\"$(Manufacturer)"\"$(ProductSoftwareName)"\CurrentVersion" ParamKeyName = $(!NTN_ServiceBase)"\"$(ProductHardwareName)"\Parameters" [GeneralConstants] from = "" to = "" ExitCodeOk = 0 ExitCodeCancel = 1 ExitCodeFatal = 2 KeyNull = "" MAXIMUM_ALLOWED = 33554432 RegistryErrorIndex = NO_ERROR KeyProduct = "" KeyParameters = "" TRUE = 1 FALSE = 0 NoTitle = 0 ExitState = "Active" OldVersionExisted = $(FALSE) DriverPath = $(!STF_NTPATH)\drivers [date] Now = {} ? $(!LIBHANDLE) GetSystemDate [Identify] read-syms Identification set Status = STATUS_SUCCESSFUL set Identifier = $(OptionType) set Media = #("Source Media Descriptions", 1, 1) Return $(Status) $(Identifier) $(Media) [ReturnOptions] set Status = STATUS_FAILED set OptionList = {} set OptionTextList = {} set LanguageList = ^(LanguagesSupported, 1) Ifcontains(i) $($0) in $(LanguageList) ifstr(i) $($1) == "" goto returnoptions endif set PlatformList = ^(PlatformsSupported, 1) Ifcontains(i) $($1) in $(PlatformList) goto returnoptions else set Status = STATUS_NOTSUPPORTED goto finish_ReturnOptions endif else set Status = STATUS_NOLANGUAGE goto finish_ReturnOptions endif returnoptions = + set OptionList = ^(Options, 1) set OptionTextList = ^(OptionsText$($0), 1) set Status = STATUS_SUCCESSFUL finish_ReturnOptions = + Return $(Status) $(OptionList) $(OptionTextList) [InstallOption] set Option = $($1) set SrcDir = $($2) set AddCopy = $($3) set DoCopy = $($4) set DoConfig = $($5) set LanguageList = ^(LanguagesSupported, 1) Ifcontains(i) $($0) NOT-IN $(LanguageList) Return STATUS_NOLANGUAGE endif Debug-Output "OEMSETUP.INF: STF_CWDDIR is: "$(!STF_CWDDIR) Debug-Output "OEMSETUP.INF: STF_LANGUAGE is: "$(!STF_LANGUAGE) set-subst LF = "\n" read-syms GeneralConstants read-syms FileConstants read-syms DialogConstants$(!STF_LANGUAGE) ifstr(i) $(!NTN_Origination) == "NCPA" set Continue = $(OK) endif read-syms FileConstants$(!STF_LANGUAGE) detect date set-title $(FunctionTitle) set to = Begin set from = Begin set CommonStatus = STATUS_SUCCESSFUL EndWait Begin = + Ifstr(i) $(!NTN_InstallMode) == deinstall set StartLabel = removeadapter else-Ifstr(i) $(!NTN_InstallMode) == Update set StartLabel = UpgradeSoftware else-Ifstr(i) $(!NTN_InstallMode) == bind set StartLabel = bindingadapter else-Ifstr(i) $(!NTN_InstallMode) == configure set CommonStatus = STATUS_REBOOT set StartLabel = configureadapter Ifstr(i) $(ProductKeyName) == $(!NTN_RegBase) Debug-Output "OEMSETUP.INF: Cannot configure the driver software." Shell $(UtilityInf),RegistryErrorString,CANNOT_CONFIGURE_SOFTWARE ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "OEMSETUP.INF: ShellCode error: cannot get an error string." goto ShellCodeError endif set Error = $($R0) set from = end set to = end goto nonfatalinfo endif else set StartLabel = installadapter set OEM_ABANDON_OPTIONS = {} set OEM_ABANDON_SOFTWARE = FALSE set OEM_ABANDON_ON = TRUE endif set IRQValue = *($(IRQList), 1) set IOBaseAddrValue = *($(IOBaseAddrList), 1) set TransceiverValue = *($(TransceiverList), 4) set StagedReceiveValue = "No" set NetworkAddressValue = "Burned-In" set EditTextIn = "1" set from = $(fatal) set to = $(fatal) goto $(StartLabel) installadapter = + OpenRegKey $(!REG_H_LOCAL) "" $(ProductKeyName) $(MAXIMUM_ALLOWED) KeyProduct Ifstr $(KeyProduct) != $(KeyNull) CloseRegKey $(KeyProduct) ifstr(i) !(NTN_RegBase) == $(ProductKeyName) Shell $(UtilityInf), VerExistedDlg, $(ProductSoftwareTitle),+ $(ProductVersion) ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "OEMSETUP.INF: ShellCode error: cannot get an error string." goto ShellCodeError endif goto end else Shell $(UtilityInf), CardExistedDlg ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "OEMSETUP.INF: ShellCode error: cannot get an error string." goto ShellCodeError endif ifstr(i) $($R1) != "OK" set CommonStatus = STATUS_USERCANCEL goto end endif set OldVersionExisted = $(TRUE) endif Endif ifint $(OldVersionExisted) == $(FALSE) ifstr(i) $(DoCopy) == "YES" ; Precopy Help File ETH16I.HLP from OEM Disk. Shell $(UtilityInf), DoAskSource, $(!STF_CWDDIR), $(SrcDir) YES Ifint $($ShellCode) != $(!SHELL_CODE_OK) Goto ShellCodeError Else-Ifstr(i) $($R0) == STATUS_FAILED Shell $(UtilityInf) RegistryErrorString "ASK_SOURCE_FAIL" ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set Error = $($R0) Goto fatal Else-Ifstr(i) $($R0) == STATUS_USERCANCEL Goto successful Endif Set SrcDir = $($R1) ; Set Subdirectory NDIS3\NT for OEM Disk. GetDriveInPath SrcDrv $(SrcDir) ifstr(i) $(SrcDrv) == "A:" Set SrcDir = $(SrcDrv)NDIS3\NT\ endif Install Install-Help endif endif Goto adapteroptions configureadapter = + Ifstr(i) $(KeyProduct) == $(KeyNull) OpenRegKey $(!REG_H_LOCAL) "" $(!NTN_RegBase) $(MAXIMUM_ALLOWED) KeyProduct Ifstr $(KeyProduct) == $(KeyNull) Set RegistryErrorIndex = CANNOT_FIND_COMPONENT_SERVICE Debug-Output "OEMSETUP.INF: Cannot find component product key" Goto fatalregistry Endif Endif Debug-Output "OEMSETUP.INF: INF: Shelling to FindService" Shell $(UtilityInf) FindService, $(KeyProduct) Ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "OEMSETUP.INF: INF: FindService shell failure" Goto ShellCodeError Endif Ifstr(i) $($R0) != NO_ERROR Debug-Output "OEMSETUP.INF: INF: FindService Shell error: "$($R0) Goto fatalregistry endif set KeyParameters = $($R2) CloseRegKey $($R1) Ifstr $(KeyParameters) == $(KeyNull) set RegistryErrorIndex = CANNOT_FIND_COMPONENT_SERVICE Debug-Output "OEMSETUP.INF: Cannot find component service" goto fatalregistry endif set OldVersionExisted = $(TRUE ) set ValueName = "" set ValueData = "" set ValueStr = "" set ValueList = {} EnumRegValue $(KeyParameters) ValueList ForListDo $(ValueList) set ValueItem = $($) set ValueName = *($(ValueItem),1) set ValueData = *($(ValueItem),4) Ifstr(i) $(ValueName) == "InterruptNumber" set IRQValueIndex = $(ValueData) else-ifstr(i) $(ValueName) == "IoBaseAddress" set IOBaseAddrIndex = $(ValueData) else-ifstr(i) $(ValueName) == "Transceiver" set TransceiverIndex = $(ValueData) else-ifstr(i) $(ValueName) == "BusType" set BusInterfaceType = $(ValueData) else-ifstr(i) $(ValueName) == "BusNumber" set BusNumber = $(ValueData) endif EndForListDo set IRQValue = *($(IRQList), ~($(IRQValues),$(IRQValueIndex))) ifstr(i) $(IRQValue) == "" set IRQValue = *($(IRQList), 1) endif set IOBaseAddrValue = *($(IOBaseAddrList), + ~($(IOBaseAddrValues),$(IOBaseAddrIndex))) ifstr(i) $(IOBaseAddrValue) == "" set IOBaseAddrValue = *($(IOBaseAddrList), 1) endif set TransceiverValue = *($(TransceiverList), + ~($(TransceiverValues),$(TransceiverIndex))) ifstr(i) $(TransceiverValue) == "" set TransceiverValue = *($(TransceiverList), 4) endif adapteroptions = + set from = adapteroptions ; Get path for Help File ETH16I.HLP SetHelpFile ETH16I.HLP 6100 6100 read-syms FileDependentDlg$(!STF_LANGUAGE) ui start "InputDlg" ifstr(i) $(DLGEVENT) == "CONTINUE" set IRQValueIndex = $(Combo1Out) set IOBaseAddrIndex = $(Combo2Out) set TransceiverIndex = $(Combo3Out) ui pop 1 goto nextstep else-ifstr(i) $(DLGEVENT) == "BACK" set CommonStatus = STATUS_USERCANCEL Debug-Output "OEMSETUP.INF: Action: exit. Bye." ui pop 1 goto end else ui pop 1 Debug-Output "OEMSETUP.INF: Action: unknown. Bye." goto end endif ifstr(i) $(!STF_NCDETINFO) == {} Shell $(UtilityInf),GetBusTypeDialog,$(ProductHardware$(Option)Description) $(BusInterfaceType) $(BusNumber) ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error." goto ShellCodeError endif set BusInterfaceType = $($R1) set BusNumber = $($R2) else ; set BusInterfaceType = *($(!STF_NCDETINFO),5) ; set BusNumber = *($(!STF_NCDETINFO),6) set BusInterfaceType = 1 set BusNumber = 0 endif nextstep = + ifint $(OldVersionExisted) == $(TRUE) ifstr(i) $(!NTN_InstallMode) == configure goto writeparameters endif endif StartWait Ifint $(OldVersionExisted) != $(FALSE) Goto installhardware Endif ifstr(i) $(!NTN_InstallMode) == "install" Ifstr(i) $(DoCopy) == "YES" Shell $(UtilityInf), DoAskSource, $(!STF_CWDDIR), $(SrcDir) YES Ifint $($ShellCode) != $(!SHELL_CODE_OK) Goto ShellCodeError Else-Ifstr(i) $($R0) == STATUS_FAILED Shell $(UtilityInf) RegistryErrorString "ASK_SOURCE_FAIL" ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set Error = $($R0) Goto fatal Else-Ifstr(i) $($R0) == STATUS_USERCANCEL Goto successful Endif Set SrcDir = $($R1) ; Set Subdirectory NDIS3\NT for OEM Disk. GetDriveInPath SrcDrv $(SrcDir) ifstr(i) $(SrcDrv) == "A:" Set SrcDir = $(SrcDrv)NDIS3\NT\ endif Endif install "Install-Option" ifstr(i) $(STF_INSTALL_OUTCOME) != STF_SUCCESS Shell $(UtilityInf) RegistryErrorString "UNABLE_COPY_FILE" ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set Error = $($R0) goto fatal endif endif Shell $(UtilityInf), AddSoftwareComponent, $(Manufacturer), + $(ProductSoftwareName), + $(ProductSoftwareName), + $(ProductSoftwareTitle), $(STF_CONTEXTINFNAME), + $(ProductSoftwareImagePath), "kernel", "NDIS", {}, "",+ $(NetEventDLL), "" Set OEM_ABANDON_SOFTWARE = TRUE ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "OEMSETUP.INF: ShellCode error" goto ShellCodeError endif set RegistryErrorIndex = $($R0) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR EndWait Debug-Output "OEMSETUP.INF: Registry error: add software components" CloseRegKey $($R1) CloseRegKey $($R2) CloseRegKey $($R3) CloseRegKey $($R4) CloseRegKey $($R5) goto fatalregistry endif Set SoftProductKey = $($R1) Set SoftNetRuleKey = $($R2) Set SoftServiceKey = $($R3) Set SoftParameterKey = $($R4) Set SoftLinkageKey = $($R5) set NewValueList = {{SoftwareType,$(NoTitle),$(!REG_VT_SZ),$(SoftwareType)},+ {MajorVersion,$(NoTitle),$(!REG_VT_DWORD),$(ProductMajorVersion)},+ {MinorVersion,$(NoTitle),$(!REG_VT_DWORD),$(ProductMinorVersion)},+ {Title,$(NoTitle),$(!REG_VT_SZ),$(ProductSoftwareTitle)},+ {Description,$(NoTitle),$(!REG_VT_SZ),$(ProductSoftwareDescription)},+ {ServiceName,$(NoTitle),$(!REG_VT_SZ),$(ProductSoftwareName)},+ {InstallDate,$(NoTitle),$(!REG_VT_DWORD),*($(Now),1)}} Shell $(UtilityInf), AddValueList, $(SoftProductKey), $(NewValueList) ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "OEMSETUP.INF: ShellCode error." goto ShellCodeError endif set RegistryErrorIndex = $($R0) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR EndWait Debug-Output "OEMSETUP.INF: Registry error: add value list for software product." CloseRegKey $(SoftProductKey) CloseRegKey $(SoftNetRuleKey) CloseRegKey $(SoftServiceKey) CloseRegKey $(SoftParameterKey) CloseRegKey $(SoftLinkageKey) goto fatalregistry endif set NewValueList = {{type,$(NoTitle),$(!REG_VT_SZ),$(NetRuleSoftwareType)},+ {use,$(NoTitle),$(!REG_VT_SZ),$(NetRuleSoftwareUse)}, + {bindform,$(NoTitle),$(!REG_VT_SZ),$(NetRuleSoftwareBindForm)}, + {class,$(NoTitle),$(!REG_VT_MULTI_SZ),$(NetRuleSoftwareClass)}, + {bindable,$(NoTitle),$(!REG_VT_MULTI_SZ),$(NetRuleSoftwareBindable)}, + {InfOption,$(NoTitle),$(!REG_VT_SZ),$(Option)}} Shell $(UtilityInf), AddValueList, $(SoftNetRuleKey), $(NewValueList) ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "OEMSETUP.INF: ShellCode error." goto ShellCodeError endif Set RegistryErrorIndex = $($R0) CloseRegKey $(SoftProductKey) CloseRegKey $(SoftNetRuleKey) CloseRegKey $(SoftServiceKey) CloseRegKey $(SoftParameterKey) CloseRegKey $(SoftLinkageKey) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR EndWait Debug-Output "OEMSETUP.INF: Registry error: add value list." goto fatalregistry endif installhardware =+ Shell $(UtilityInf), AddHardwareComponent, $(ProductHardwareName),$(STF_CONTEXTINFNAME),$(ProductKeyName) ifint $($R4) != -1 Set OEM_ABANDON_OPTIONS = >($(OEM_ABANDON_OPTIONS), $(!NTN_SoftwareBase)"\Microsoft\Windows NT\CurrentVersion\NetworkCards\"$($R4)) endif ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "OEMSETUP.INF: Cannot add hardware component" goto ShellCodeError endif set RegistryErrorIndex = $($R0) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR EndWait Debug-Output "OEMSETUP.INF: Registry error: add hardware component" CloseRegKey $($R1) CloseRegKey $($R2) CloseRegKey $($R3) goto fatalregistry endif set KeyProduct = $($R1) set KeyAdapterRules = $($R2) set KeyParameters = $($R3) set AdapterNumber = $($R4) set NewValueList = {{Manufacturer,$(NoTitle),$(!REG_VT_SZ),$(Manufacturer)},+ {Title,$(NoTitle),$(!REG_VT_SZ),"["$($R4)"] "$(ProductHardware$(Option)Title)},+ {Description,$(NoTitle),$(!REG_VT_SZ),$(ProductHardware$(Option)Description)},+ {ProductName,$(NoTitle),$(!REG_VT_SZ),$(ProductHardwareName)},+ {ServiceName,$(NoTitle),$(!REG_VT_SZ),$($R5)},+ {InstallDate,$(NoTitle),$(!REG_VT_DWORD),*($(Now),1)}} Shell $(UtilityInf), AddValueList, $(KeyProduct), $(NewValueList) ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "OEMSETUP.INF: ShellCode error" goto ShellCodeError endif CloseRegKey $(KeyProduct) Set KeyProduct = "" set TempProdName = """"$(ProductHardwareName)$(AdapterNumber)"""" set TempBindForm = $(TempProdName)$(NetRuleHardwareBindForm) set NewValueList = {{type,$(NoTitle),$(!REG_VT_SZ),$(NetRuleHardwareType)},+ {bindform,$(NoTitle),$(!REG_VT_SZ),$(TempBindForm)}, + {class,$(NoTitle),$(!REG_VT_MULTI_SZ),$(NetRuleHardwareClass)}, + {InfOption,$(NoTitle),$(!REG_VT_SZ),$(Option)}} Shell $(UtilityInf), AddValueList, $(KeyAdapterRules), $(NewValueList) ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "OEMSETUP.INF: ShellCode error." goto ShellCodeError endif CloseRegKey $(KeyAdapterRules) Set RegistryErrorIndex = $($R0) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR EndWait Debug-Output "OEMSETUP.INF: Registry error: add value list." CloseRegKey $(KeyParameters) goto fatalregistry Endif writeparameters = + Ifstr(i) $(KeyParameters) == $(KeyNull) Debug-Output "OEMSETUP.INF: *** KeyParameters is NULL at writeparameters" Endif set IRQValue = *($(IRQValues), ~($(IRQList),$(IRQValueIndex))) set IOBaseAddrValue = *($(IOBaseAddrValues), + ~($(IOBaseAddrList),$(IOBaseAddrIndex))) set TransceiverValue = *($(TransceiverValues), + ~($(TransceiverList),$(TransceiverIndex))) set NewValueList = {+ {MediaType,$(NoTitle),$(!REG_VT_DWORD),1},+ {BusType,$(NoTitle),$(!REG_VT_DWORD),$(BusInterfaceType)},+ {BusNumber,$(NoTitle),$(!REG_VT_DWORD),$(BusNumber)},+ {InterruptNumber,$(NoTitle),$(!REG_VT_DWORD),$(IRQValue)},+ {IoBaseAddress,$(NoTitle),$(!REG_VT_DWORD),$(IOBaseAddrValue)},+ {Transceiver,$(NoTitle),$(!REG_VT_SZ),$(TransceiverValue)},+ {StagedReceive,$(NoTitle),$(!REG_VT_SZ),$(StagedReceiveValue)},+ {NetworkAddress,$(NoTitle),$(!REG_VT_SZ),$(NetworkAddressValue)},+ {TransmitBufferSize,$(NoTitle),$(!REG_VT_DWORD),8)}} Shell $(UtilityInf), AddValueList, $(KeyParameters), $(NewValueList) ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "OEMSETUP.INF: ShellCode error." goto ShellCodeError endif Set RegistryErrorIndex = $($R0) CloseRegKey $(KeyParameters) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR Debug-Output "OEMSETUP.INF: Registry error: Add value list" goto fatalregistry Endif EndWait goto successful bindingadapter =+ set Error = "Binding: Sorry, not yet implemented." goto fatal removeadapter = + Ifstr(i) $(ProductKeyName) == $(!NTN_RegBase) Shell $(UtilityInf), RemoveSoftwareComponent, $(Manufacturer), + $(ProductSoftwareName) ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "OEMSETUP.INF: ShellCode error" goto ShellCodeError endif set RegistryErrorIndex = $($R0) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR goto fatalregistry endif else Shell $(UtilityInf), RemoveHardwareComponent, $(Manufacturer), + $(ProductSoftwareName), $(!NTN_RegBase) ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "OEMSETUP.INF: ShellCode error" goto ShellCodeError endif set RegistryErrorIndex = $($R0) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR goto fatalregistry endif endif goto end UpgradeSoftware = + ifstr(i) $(ProductKeyName) == $(!NTN_RegBase) OpenRegKey $(!REG_H_LOCAL) "" $(ProductKeyName) $(MAXIMUM_ALLOWED) KeyProduct Ifstr $(KeyProduct) != $(KeyNull) GetRegValue $(KeyProduct),"MajorVersion", VersionInfo set Version = *($(VersionInfo), 4) Shell $(UtilityInf), GetInfFileNameFromRegistry, $(KeyProduct) ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error" goto ShellCodeError endif set !UG_Filename = $($R0) ifstr(i) $(!UG_Filename) != "" install "Install-Update" ifstr(i) $(STF_INSTALL_OUTCOME) != STF_SUCCESS goto fatal endif endif SetRegValue $(KeyProduct) {MajorVersion,$(NoTitle),$(!REG_VT_SZ),$(ProductMajorVersion)} SetRegValue $(KeyProduct) {MinorVersion,$(NoTitle),$(!REG_VT_SZ),$(ProductMinorVersion)} ifint $(Version) != $(ProductVersion) endif CloseRegKey $(KeyProduct) else goto fatalregistry endif else OpenRegKey $(!REG_H_LOCAL) "" $(!NTN_RegBase) + $(MAXIMUM_ALLOWED) NetworkCardKey Ifstr(i) $(NetworkCardKey) != $(KeyNull) GetRegValue $(NetworkCardKey),"ServiceName", ServiceNameInfo set ServiceName = *($(ServiceNameInfo), 4) OpenRegKey $(NetworkCardKey) "" "NetRules" + $(MAXIMUM_ALLOWED) NetRuleKey Ifstr(i) $(NetRuleKey) != $(KeyNull) else goto fatalregistry endif CloseRegKey $(NetRules) CloseRegKey $(NetworkCardKey) else goto fatalregistry endif OpenRegKey $(!REG_H_LOCAL) "" + $(!NTN_ServiceBase)"\"$(ServiceName) + $(MAXIMUM_ALLOWED) ServiceKey Ifstr(i) $(ServiceKey) != $(KeyNull) CloseRegKey $(ServiceKey) else goto fatalregistry endif endif goto end successful = + goto end abandon = + ForListDo $(OEM_ABANDON_OPTIONS) Shell $(UtilityInf), RemoveHardwareComponent, $(Manufacturer), + $(ProductSoftwareName), $($) ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "OEMSETUP.INF: ShellCode error" goto ShellCodeError endif set RegistryErrorIndex = $($R0) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR goto fatalregistry endif EndForListDo Ifstr(i) $(OEM_ABANDON_SOFTWARE) == TRUE Shell $(UtilityInf), RemoveSoftwareComponent, $(Manufacturer), + $(ProductSoftwareName), FALSE ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "OEMSETUP.INF: ShellCode error" goto ShellCodeError endif set RegistryErrorIndex = $($R0) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR goto fatalregistry endif endif goto end warning = + Shell $(subroutineinf) SetupMessage, $(!STF_LANGUAGE), "WARNING", $(Error) ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif ifstr(i) $($R1) == "OK" goto $(to) else-ifstr(i) $($R1) == "CANCEL" goto $(from) else goto "end" endif nonfatalinfo = + Set CommonStatus = STATUS_USERCANCEL Set Severity = STATUS goto nonfatalmsg nonfatal = + Set Severity = NONFATAL goto nonfatalmsg nonfatalmsg = + ifstr(i) $(Error) == "" Set Severity = NONFATAL Shell $(UtilityInf) RegistryErrorString "SETUP_FAIL" ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set Error = $($R0) endif Shell $(subroutineinf) SetupMessage, $(!STF_LANGUAGE), $(Severity), $(Error) ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif ifstr(i) $($R1) == "OK" goto $(from) else goto "end" endif fatalregistry = + Shell $(UtilityInf) RegistryErrorString $(RegistryErrorIndex) ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set Error = $($R0) goto fatal fatal = + ifstr(i) $(Error) == "" Shell $(UtilityInf) RegistryErrorString "SETUP_FAIL" ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set Error = $($R0) endif Shell $(subroutineinf) SetupMessage, $(!STF_LANGUAGE), "FATAL", $(Error) ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif goto setfailed ShellCodeError = + set DlgType = "MessageBox" set STF_MB_TITLE = $(ShellCodeErrorTitle) set STF_MB_TEXT = $(ShellCodeErrorText) set STF_MB_TYPE = 1 set STF_MB_ICON = 3 set STF_MB_DEF = 1 ui start "Error Message" goto setfailed setfailed = + set CommonStatus = STATUS_FAILED ifstr(i) $(OEM_ABANDON_ON) == TRUE set OEM_ABANDON_ON = FALSE goto abandon endif goto end end = + goto term term = + Return $(CommonStatus) [Install-Option] set STF_VITAL = "" ifstr(i) $(AddCopy) == "YES" AddSectionFilesToCopyList Files-$(Option) $(SrcDir) $(!STF_WINDOWSSYSPATH)\drivers AddNthSectionFileToCopyList Files-Inf 2 $(SrcDir) $(!STF_WINDOWSSYSPATH) endif Debug-Output "OEMSETUP.INF: [Install-Option] DoCopy = "$(DoCopy) ifstr(i) $(DoCopy) == "YES" set !STF_NCPA_FLUSH_COPYLIST = TRUE CopyFilesInCopyList endif ifstr(i) $(DoConfig) == "YES" endif Exit [Install-Update] set STF_VITAL = "" set STF_OVERWRITE = "VERIFYSOURCEOLDER" AddSectionFilesToCopyList Files-$(Option) $(SrcDir) $(!STF_WINDOWSSYSPATH)\drivers AddSectionFilesToCopyList Files-Inf $(SrcDir) $(!STF_WINDOWSSYSPATH) AddNthSectionFileToCopyList Files-Inf 2 $(SrcDir) $(!STF_WINDOWSSYSPATH) set !STF_NCPA_FLUSH_COPYLIST = TRUE CopyFilesInCopyList exit [Install-Help] set STF_VITAL = "" set STF_OVERWRITE = "VERIFYSOURCEOLDER" AddNthSectionFileToCopyList Files-Inf 2 $(SrcDir) $(!STF_WINDOWSSYSPATH) set !STF_NCPA_FLUSH_COPYLIST = TRUE CopyFilesInCopyList exit [Source Media Descriptions] 1 = "Windows NT Setup Disk #1" , TAGFILE = disk1 2 = "Windows NT Setup CD-ROM Disk" , TAGFILE = disk2 3 = "EtherTeam16i/32 Driver Disk" , TAGFILE = ndis3\nt\eth16i.sys [ProductType] STF_PRODUCT = Winnt STF_PLATFORM = I386 [Files-Inf] 3, oemsetup.inf, SIZE=1000, RENAME=$(!UG_Filename) 3, ETH16I.HLP, SIZE=999 [Files-ETH16I] 3,ETH16I.SYS , SIZE=45568 [Files-ETH32] 3,ETH16I.SYS , SIZE=45568 [LanguagesSupported] ENG [OptionsTextENG] ETH16I = "ICL EtherTeam16i Adapter" ETH32 = "ICL EtherTeam32 Adapter" [FileConstantsENG] ProCaption = "Windows NT Setup" ProCancel = "Cancel" ProCancelMsg = "Windows NT Networking is not correctly installed. "+ "Are you sure you want to cancel copying files?" ProCancelCap = "Network Setup Message" ProText1 = "Copying:" ProText2 = "To:" FunctionTitle = "ICL EtherTeam16i/32 Adapter Card Setup" ProductSoftwareDescription = "ICL EtherTeam16i/32 Adapter Driver" ProductHardwareETH16IDescription = "ICL EtherTeam16i Adapter" ProductHardwareETH32Description = "ICL EtherTeam32 Adapter" ProductSoftwareTitle = "ICL EtherTeam16i/32 Driver" ProductHardwareETH16ITitle = "ICL EtherTeam16i Adapter" ProductHardwareETH32Title = "ICL EtherTeam32 Adapter" IRQList = ^(IRQChoices$(Option), 1) IRQValues = ^(IRQChoices$(Option), 2) IOBaseAddrList = ^(IOBaseAddrChoices$(Option), 1) IOBaseAddrValues = ^(IOBaseAddrChoices$(Option), 2) TransceiverList = ^(TransceiverChoices$(Option), 1) TransceiverValues = ^(TransceiverChoices$(Option), 2) ShellCodeErrorTitle = "Error: "$(FunctionTitle) ShellCodeErrorText = "Shell Code Error." [DialogConstantsENG] Help = "&Help" Exit = "Cancel" OK = "OK" HelpContext = "" Continue = "Continue" Cancel = "Cancel" [FileDependentDlgENG] Label1 = "&Interrupt Number:" Label2 = "I/O &Base Address:" Label3 = "&Transceiver:" DlgType = "Combination" DlgTemplate = "UBNDIS" Caption = $(FunctionTitle) Combo1List = $(IRQList) Combo1Out = $(IRQValue) Combo2List = $(IOBaseAddrList) Combo2Out = $(IOBaseAddrValue) Combo3List = $(TransceiverList) Combo3Out = $(TransceiverValue) ComboListItemsIn = {Combo1List, Combo2List, Combo3List} ComboListItemsOut = {Combo1Out, Combo2Out, Combo3Out} EditTextLim = "" CBOptionsGreyed = {} HelpContext = 6100Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.