1. en2226-1.zip Driver
2. README.TXT File Contents

README.TXT Driver File Contents (en2226-1.zip)

FTP Software PC/TCP
Packet, NDIS 2.0, and ODI Drivers

FTP Software's PC/TCP Generic Ethernet Kernel ETHDRV.EXE can be installed
using Accton's Packet, ODI, or NDIS drivers. PC/TCP can also be used
concurrently with NetWare. For information on which driver is appropriate
for your network environments, see the following information.

FTP PC/TCP 3.X with OnNet 1.1 and Windows for Workgroups 3.11

 1. Run the Accton Installation Program from Installation Disk.
 2. From the Select Network Operating System screen, choose Microsoft
    Windows for Workgroups then FTP PC/TCP 3.x.
 3. Follow the prompt to complete the Accton segment of the installation.
 4. Run the PC/TCP installation OnNet 1.1.
 5. Follow the prompts to the Network Card Screen, then select "Other NDIS
    Driver or Updated Packet Driver."
 6. Insert the Accton Drivers Disk when prompted.
 7. Choose the appropriate driver then follow prompts to complete the
    installation.
8a. For NDIS installation, reboot the PC.
8b. For ODI installation, do not reboot. Continue with step 9.

Additional Steps for ODI Installation
If you are using an ODI driver, continue with the following steps:

 9. Change to the directory into which PC/TCP was installed.
10. Use a text editor to change the file PCTCP.INI as follows:
    In the section PCTCP ifcust 0 change the line
      INTERFACE-TYPE=NDIS
    to read
      INTERFACE-TYPE=PKTDRV.
11. Save the file and exit the text editor.
12. Change to the C:\ (root) directory.
13. Use a text editor to modify the AUTOEXEC.BAT file as follows (\PCTCP
    is the default installation directory):
    - Move the line containing the STARTNET.BAT command or the lines
      containing the network driver files to immediately above the line
        SET PCTCP=C:\PCTCP\PCTCP.INI
    - Add the line
        C:\PCTCP\ODIPKT
      after the line
        PCTCP=C:\PCTCP\PCTCP.INI
14. Save the file and exit the text editor.
15. Copy the file ODIPKT from disk 5 of the FTP PC/TCP installation disks
    to the directory into which PC/TCP was installed.
16. Reboot the PC.

FTP PC/TCP 3.X with OnNet 1.1 with Windows 3.1

 1. Run the Accton Installation Program from Installation Disk.
 2. From the Select Network Operating System screen, choose FTP PC/TCP.
 3. Follow the prompts to complete the Accton installation.
 4. Run the PC/TCP installation program OnNet 1.1.
 5. When prompted, insert the Accton Drivers Disk.
 6. Follow prompts to complete the PC/TCP installation.
7a. For an NDIS installation, reboot the PC.
7b. For ODI installation, do not reboot. Continue with step 8.

Additional Setps for ODI Installation
If you are using an ODI driver, continue with the following steps:

 8. Change to the directory into which PC/TCP was installed.
 9. Use a text editor to change the file PCTCP.INI as follows:
    In the section PCTCP ifcust 0 change the line
      INTERFACE-TYPE=NDIS
    to read
      INTERFACE-TYPE=PKTDRV.
10. Save the file and exit the text editor.
11. Change to the C:\ (root) directory.
12. Use a text editor to modify the AUTOEXEC.BAT file as follows (\PCTCP
    is the default installation directory):
    - Move the line containing the STARTNET.BAT command or the lines
      containing the network driver files to immediately above the line
        SET PCTCP=C:\PCTCP\PCTCP.INI
    - Add the line
        C:\PCTCP\ODIPKT
      after the line
        PCTCP=C:\PCTCP\PCTCP.INI
13. Save the file and exit the text editor.
14. Copy the file ODIPKT from disk 5 of the FTP PC/TCP installation disks
    to the directory into which PC/TCP was installed.
15. Reboot the PC.

FTP Software PC/TCP Packet Driver Installation

 1. Run the Accton Installation Program from Installation Disk.
 2. Choose FTP PC/TCP fFrom the Select Network Operating System screen.
 3. Follow the prompts to complete the Accton segment of the installation.
 4. Install PC/TCP software according to the directions given in the PC/TCP
    documentation.
 5. Copy the files OPEN16.EXE, EN2226PD.COM, and ACCTONPD.BAT from the
    C:\ACCTON\2226 directory to the PC/TCP directory specified in the
    PC/TCP install procedure. The file ACCTONPD.BAT contains the correct
    command lines for the Packet Driver.
 6. (This step is not required for PC/TCP versions 2.10 and later.) Using
    a text editor, add the following lines to your CONFIG.SYS file:
      DEVICE=[PATH]IPCUST.SYS
      DEVICE=[PATH]IFCUST.SYS
    where [PATH] is the drive and directory specified at the PC/TCP
    installation.
 7. Reboot the PC.
 8. Change to the directory where your PC/TCP files are stored and run
    ACCTONPD.BAT by typing: ACCTONPD
 9. Run the ETHDRV.EXE kernel program supplied with PC/TCP. This loads
    the PC/TCP kernel into memory. The packet driver must always load
    before the kernel.
10. Continue your server or workstation startup as instructed in the
    PC/TCP documentation.

ODI with FTP Software PC/TCP and NetWare
If you need to run Novell NetWare concurrently with FTP PC/TCP, proceed
as follows:

 1. Run the Accton Installation Program from Installation Disk.
 2. Choose FTP PC/TCP from the Select Network Operating System screen.
 3. Follow the prompts to complete the Accton segment of the installation.
 4. Install PC/TCP according to the instructions in your FTP PC/TCP manual.
 5. (This step is not required for PC/TCP versions 2.10 and later.) Using
    a text editor, add the following lines to your CONFIG.SYS file:
      DEVICE=[PATH]IPCUST.SYS
      DEVICE=[PATH]IFCUST.SYS
    where [PATH] is the drive and directory specified at the PC/TCP
    installation. 
 6. Copy the file OPEN16.EXE and NET.CFG from the C:\ACCTON\2226 directory
    and the files LSL.COM and ACC2226.COM from the root directory of the
    Accton Drivers Disk to the PC/TCP directory created in the PC/TCP
    install procedure.
 7. To start the workstation, load the software as follows:
      OPEN16.EXE DRIVER=ODI
      LSL
      ACC2226
      IPXODI
      ODIPKT (USE THE VERSION SUPPLIED WITH PC/TCP)
      ETHDRV
      VLM
 8. Change to the network drive (usually F:\LOGIN).
 9. Log in to the network.