;************************************************************************************
;
; OEMSETUP.INF
;
; Accton Fast Ethercard-16 10/100 PC Card Setup for NT 3.51 and higher
;
;*************************************************************************************
[Identification]
OptionType = NetAdapter
[PlatformsSupported]
ISA
EISA
MCA
[Options]
EN2226
[OptionsTextENG]
EN2226 = "Accton Fast EtherCard-16 10/100 PC Card"
[AllFileConstants]
GenericInfVersion = " v1.35"
; File names, etc. ----------------------------------------
UtilityInf = "UTILITY.INF"
ParamInf = "NCPARAM.INF"
subroutineinf = "SUBROUTN.INF"
SoftwareType = "driver"
Exit_Code = 0
; EventLog Message File ----------------------------------------
NetEventDLL = "%SystemRoot%\System32\netevent.dll;%SystemRoot%\System32\drivers\en2226.sys"
IoLogMsgDLL = "%SystemRoot%\System32\IoLogMsg.dll"
; Product Info ----------------------------------------
Manufacturer = "Accton"
; Flow control variables ----------------------------------------
RUNDLLCODE = 0
HOTPROGRAMPCMCIA = ""
[FileConstants-EN2226]
GenericAdapterName = "Accton Fast EtherCard-16 10/100 PC Card"
GenericDriverName = "Accton Fast EtherCard-16 10/100 PC Card"
GenericTitleName = "Accton Fast EtherCard-16 10/100 PC Card"
GenericSysName = "EN2226.SYS"
GenericName = "EN2226"
; Product Info ----------------------------------------
ProductMajorVersion = "3"
ProductMinorVersion = "12"
ProductVersion = $(ProductMajorVersion)"."$(ProductMinorVersion)
; Software ----------------------------------------
ProductSoftwareName = "EN2226"
ProductSoftwareDescription = "Accton Fast EtherCard-16 10/100 PC Card"
ProductSoftwareImagePath = "\SystemRoot\System32\drivers\"$(GenericSysName)
NetRuleSoftwareType = "en2226Sys ndisDriver en2226Driver"
NetRuleSoftwareUse = $(SoftwareType)
NetRuleSoftwareBindForm = """en2226Sys"" yes no container"
NetRuleSoftwareClass = {"en2226Driver basic"}
NetRuleSoftwareBindable = {"en2226Driver en2226Adapter non exclusive 100"}
; Hardware ----------------------------------------
ProductHardwareName = "EN2226"
ProductHardwareDescription = "Accton Fast EtherCard-16 10/100 PC Card"
NetRuleHardwareType = "en2226 en2226Adapter"
NetRuleHardwareBindForm = " yes yes container"
NetRuleHardwareClass = {"en2226Adapter basic"}
; Registry Key ----------------------------------------
ProductKeyName = $(!NTN_SoftwareBase)"\"$(Manufacturer)"\"$(ProductSoftwareName)"\CurrentVersion"
ParamKeyName = $(!NTN_ServiceBase)"\"$(ProductHardwareName)"\Parameters"
; Tuple Information -----------------------------------
VERS1Manufacturer = "Accton"
VERS1Product = "Fast EtherCard-16"
VERS1Type = "EN2226"
[GeneralConstants]
; Program flow control variables.
from = ""
to = ""
; Return codes; Exit_Code is set to one of these
ExitCodeOk = 0
ExitCodeCancel = 1
ExitCodeFatal = 2
KeyNull = ""
MAXIMUM_ALLOWED = 33554432
RegistryErrorIndex = NO_ERROR
KeyProduct = ""
KeyParameters = ""
TRUE = 1
FALSE = 0
NoTitle = 0
ExitState = "Active"
OldVersionExisted = $(FALSE)
DriverPath = $(!STF_NTPATH)\drivers
[date]
; Now is a list which contains { Sec from 1-1-1970, Year, Month, Day, Hour,
; Minute, Second }
Now = {} ? $(!LIBHANDLE) GetSystemDate
;---------------------------------------------------------------------------
; 1. Identify
;
; DESCRIPTION: To verify that this INF deals with the same type of options
; as we are choosing currently.
;
; INPUT: None
;
; OUTPUT: $($R0): STATUS: STATUS_SUCCESSFUL
; $($R1): Option Type (COMPUTER ...)
; $($R2): Diskette description
;---------------------------------------------------------------------------
[Identify]
;
;
read-syms Identification
set Status = STATUS_SUCCESSFUL
set Identifier = $(OptionType)
set Media = #("Source Media Descriptions", 1, 1)
Return $(Status) $(Identifier) $(Media)
;------------------------------------------------------------------------
; 2. ReturnOptions:
;
; DESCRIPTION: To return the option list supported by this INF and the
; localised text list representing the options.
;
;
; INPUT: $($0): Language used. ( ENG | FRN | ... )
;
; OUTPUT: $($R0): STATUS: STATUS_SUCCESSFUL |
; STATUS_NOLANGUAGE
; STATUS_FAILED
; STATUS_NOTSUPPORTED
;
; $($R1): Option List
; $($R2): Option Text List
;------------------------------------------------------------------------
[ReturnOptions]
;
;
set Status = STATUS_FAILED
set OptionList = {}
set OptionTextList = {}
;
; Check if the language requested is supported
;
set LanguageList = ^(LanguagesSupported, 1)
Ifcontains(i) $($0) in $(LanguageList)
;
; Check if the platforms requested is supported
;
ifstr(i) $($1) == ""
goto returnoptions
endif
set PlatformList = ^(PlatformsSupported, 1)
Ifcontains(i) $($1) in $(PlatformList)
goto returnoptions
else
set Status = STATUS_NOTSUPPORTED
goto finish_ReturnOptions
endif
else
set Status = STATUS_NOLANGUAGE
goto finish_ReturnOptions
endif
;
; form a list of all the options and another of the text representing
;
returnoptions = +
set OptionList = ^(Options, 1)
set OptionTextList = ^(OptionsText$($0), 1)
set Status = STATUS_SUCCESSFUL
finish_ReturnOptions = +
Return $(Status) $(OptionList) $(OptionTextList)
;------------------------------------------------------------------------
;
; InstallOption:
;
; This section is shelled to by main installation processing
; or by NCPASHEL.INF during reconfig, removal, update, etc.
;
;
; FUNCTION: To copy files representing Options
; To configure the installed option
; To update the registry for the installed option
;
; INPUT: $($0): Language to use
; $($1): OptionID to install
; $($2): SourceDirectory
; $($3): AddCopy (YES | NO)
; $($4): DoCopy (YES | NO)
; $($5): DoConfig (YES | NO)
;
; OUTPUT: $($R0): STATUS: STATUS_SUCCESSFUL |
; STATUS_NOLANGUAGE |
; STATUS_USERCANCEL |
; STATUS_FAILED
;
;------------------------------------------------------------------------
[InstallOption]
;
; Set default values for
;
set Status = STATUS_FAILED
;
; extract parameters
;
set Option = $($1)
set SrcDir = $($2)
set AddCopy = $($3)
set DoCopy = $($4)
set DoConfig = $($5)
Set !DebugOutputControl = 1
;
; Check if the language requested is supported
;
set LanguageList = ^(LanguagesSupported, 1)
Ifcontains(i) $($0) NOT-IN $(LanguageList)
Return STATUS_NOLANGUAGE
endif
set-subst LF = "\n"
read-syms GeneralConstants
read-syms AllFileConstants
read-syms FileConstants"-"$(Option)
read-syms DialogConstants$(!STF_LANGUAGE)"-"$(Option)
ifstr(i) $(!NTN_Origination) == "NCPA"
set Continue = $(OK)
endif
read-syms AllFileConstants$(!STF_LANGUAGE)
read-syms FileConstants$(!STF_LANGUAGE)"-"$(Option)
detect date
set-title $(FunctionTitle)
set to = Begin
set from = Begin
;
; Assume all is well.
;
set CommonStatus = STATUS_SUCCESSFUL
EndWait
;
; Set up the operation-mode-based variables and gaily welcome
; the user. If the "install mode" variable is improperly set,
; assume this is a new installation.
;
Begin = +
Set ActivateDetection = FALSE
Ifstr(i) $(!NTN_InstallMode) == deinstall
set StartLabel = removeadapter
else-Ifstr(i) $(!NTN_InstallMode) == Update
set StartLabel = UpgradeSoftware
else-Ifstr(i) $(!NTN_InstallMode) == bind
set StartLabel = bindingadapter
else-Ifstr(i) $(!NTN_InstallMode) == configure
; set ActivateDetection = TRUE
set StartLabel = configureadapter
;
; You cannot config the software component
;
Ifstr(i) $(ProductKeyName) == $(!NTN_RegBase)
;Debug-Output "Cannot configure the software."
Shell $(UtilityInf),RegistryErrorString,CANNOT_CONFIGURE_SOFTWARE
ifint $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output "ShellCode error: cannot get an error string."
goto ShellCodeError
endif
set Error = $($R0)
set from = end
set to = end
goto nonfatalinfo
endif
else
; set ActivateDetection = TRUE
set StartLabel = installadapter
set OEM_ABANDON_OPTIONS = {}
set OEM_ABANDON_SOFTWARE = FALSE
set OEM_ABANDON_ON = TRUE
endif
; set the [Default values]
set IRQValue = *($(IRQList), 3) ; IRQ Level = 10
set IOBaseAddrValue = *($(IOBaseAddrList), 18) ; IOBase Address = 0x320
set MemoryAddrValue = *($(MemoryAddrList), 53) ; Memory Address = 0xD0000
set CableTypeValue = *($(CableTypeList), 1) ; Cable Type = Auto Detect
set FullDuplexValue = "OFF" ; Full Duplex = off
set LinkIntegrityValue = "ON" ; Link Integrity = Enabled
set EarlyTransmitValue = "ON" ; Early Transmit = on
set DirectEnableValue = "OFF" ; Direct Enable = off
set PcmciaValue = "ON" ; Pcmcia Enabler = 1
set ModeValue = *($(ModeList), 1) ; Mode = I/O
set LineSpeedValue = *($(LineSpeedList), 1) ; LineSpeed = auto
;set NetworkAddressValue = "99 99 99 99 99 99"
Set from = $(fatal)
Set to = $(fatal)
Goto $(StartLabel)
;-----------------------------------------------
; Installation Section
;-----------------------------------------------
installadapter = +
;
; First, check whether the same version of the software exists
;
OpenRegKey $(!REG_H_LOCAL) "" $(ProductKeyName) $(MAXIMUM_ALLOWED) KeyProduct
Ifstr $(KeyProduct) != $(KeyNull)
;
; Same version already existed in the local machine
; Popup the dialog and ask the user whether he wants to continue
;
CloseRegKey $(KeyProduct)
ifstr(i) !(NTN_RegBase) == $(ProductKeyName)
;
; Cannot Install the same software again
;
Shell $(UtilityInf), VerExistedDlg, $(ProductSoftwareTitle),+
$(ProductVersion)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output "ShellCode error: cannot get an error string."
goto ShellCodeError
endif
goto end
else
;
; Add a new adapter card?
;
Shell $(UtilityInf), CardExistedDlg
ifint $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output "ShellCode error: cannot get an error string."
goto ShellCodeError
endif
ifstr(i) $($R1) != "OK"
goto end
endif
set OldVersionExisted = $(TRUE)
endif
endif
;
; dll load addition
;
Shell $(UtilityInf), DoAskSource, $(!STF_CWDDIR), $(SrcDir) NO
Ifint $($ShellCode) != $(!SHELL_CODE_OK)
Goto ShellCodeError
Else-Ifstr(i) $($R0) == STATUS_FAILED
Shell $(UtilityInf) RegistryErrorString "ASK_SOURCE_FAIL"
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set Error = $($R0)
Goto fatal
Else-Ifstr(i) $($R0) == STATUS_USERCANCEL
Goto successful
Endif
Set SrcDir = $($R1)
install "Install-Dll"
goto adaptersetup
;-----------------------------------------------
; Configuration Section
;-----------------------------------------------
;
; Get the current values of all the parameters
;
configureadapter = +
Ifstr $(KeyProduct) == $(KeyNull)
OpenRegKey $(!REG_H_LOCAL) "" $(!NTN_RegBase) $(MAXIMUM_ALLOWED) KeyProduct
Ifstr $(KeyProduct) == $(KeyNull)
set RegistryErrorIndex = CANNOT_FIND_COMPONENT_SERVICE
Debug-Output "Cannot find component product key"
goto fatalregistry
Endif
Endif
;
; Get the other parameters; they're attached to the service parameters key
;
Debug-Output "INF: Shelling to FindService"
Shell $(UtilityInf) FindService, $(KeyProduct)
Ifint $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output "INF: FindService shell failure"
Goto ShellCodeError
Endif
Ifstr(i) $($R0) != NO_ERROR
Debug-Output "INF: FindService Shell error: "$($R0)
Goto fatalregistry
endif
Set KeyParameters = $($R2)
;
; We don't need the services key, so close it.
;
CloseRegKey $($R1)
Ifstr $(KeyParameters) == $(KeyNull)
set RegistryErrorIndex = CANNOT_FIND_COMPONENT_SERVICE
Debug-Output "Cannot find component service"
goto fatalregistry
endif
set OldVersionExisted = $(TRUE)
set ValueName = ""
set ValueData = ""
set ValueStr = ""
set ValueList = {}
;
; Get the old values from the Registry [Get Values]
; *********************************************************
EnumRegValue $(KeyParameters) ValueList
ForListDo $(ValueList)
set ValueItem = $($)
set ValueName = *($(ValueItem),1)
set ValueData = *($(ValueItem),4)
ifstr(i) $(ValueName) == "IoBaseAddress"
set IOBaseAddrIndex = $(ValueData)
else-ifstr(i) $(ValueName) == "InterruptNumber"
set IRQValueIndex = $(ValueData)
else-ifstr(i) $(ValueName) == "EarlyTransmit"
set EarlyTransmitValue = $(ValueData)
else-ifstr(i) $(ValueName) == "DirectEnable"
set DirectEnableValue = $(ValueData)
else-ifstr(i) $(ValueName) == "LinkIntegrity"
set LinkIntegrityValue = $(ValueData)
else-ifstr(i) $(ValueName) == "FullDuplex"
set FullDuplexValue = $(ValueData)
else-ifstr(i) $(ValueName) == "CableType"
set CableTypeIndex = $(ValueData)
else-ifstr(i) $(ValueName) == "PCCARDAttributeMemoryAddress"
set MemoryAddrIndex = $(ValueData)
else-ifstr(i) $(ValueName) == "NetworkAddress"
set NetworkAddressValue = $(ValueData)
else-ifstr(i) $(ValueName) == "Mode"
set ModeIndex = $(ValueData) ; mode value is base 0
else-ifstr(i) $(ValueName) == "LineSpeed"
set LineSpeedIndex = $(ValueData)
endif
EndForListDo
set IRQValue = *($(IRQList), ~($(IRQValues),$(IRQValueIndex)))
ifstr(i) $(IRQValue) == ""
set IRQValue = *($(IRQList), 2)
endif
set MemoryAddrValue = *($(MemoryAddrList), ~($(MemoryAddrValues),$(MemoryAddrIndex)))
ifstr(i) $(MemoryAddrValue) == ""
set MemoryAddrValue = *($(MemoryAddrValues), 2)
endif
set IOBaseAddrValue = *($(IOBaseAddrList), ~($(IOBaseAddrValues),$(IOBaseAddrIndex)))
ifstr(i) $(IOBaseAddrValue) == ""
set IOBaseAddrValue = *($(IOBaseAddrList), 1)
endif
set ModeValue = *($(ModeList), ~($(ModeValues),$(ModeIndex)))
ifstr(i) $(ModeValue) == ""
set ModeValue = *($(ModeValues), 2)
endif
set CableTypeValue = *($(CableTypeList), ~($(CableTypeValues),$(CableTypeIndex)))
ifstr(i) $(CableTypeValue) == ""
set CableTypeValue = *($(CableTypeValues), 2)
endif
set LineSpeedValue = *($(LineSpeedList), ~($(LineSpeedValues),$(LineSpeedIndex)))
ifstr(i) $(LineSpeedValue) == ""
set LineSpeedValue = *($(LineSpeedValues), 0)
endif
ifstr(i) $(EarlyTransmitValue) == ""
set EarlyTransmitValue = 1
endif
ifstr(i) $(DirectEnableValue) == ""
set DirectEnableValue = 0
set PcmciaValue = 1
endif
ifstr(i) $(LinkIntegrityValue) == ""
set LinkIntegrityValue = 1
endif
ifstr(i) $(FullDuplexValue) == ""
set FullDuplexValue = 0
endif
ifint $(EarlyTransmitValue) == 1
set EarlyTransmitValue = "ON"
else
set EarlyTransmitValue = "OFF"
endif
ifint $(DirectEnableValue) == 1
set DirectEnableValue = "ON"
set PcmciaValue = "OFF"
else
set DirectEnableValue = "OFF"
set PcmciaValue = "ON"
endif
ifint $(LinkIntegrityValue) == 1
set LinkIntegrityValue = "ON"
else
set LinkIntegrityValue = "OFF"
endif
ifint $(FullDuplexValue) == 1
set FullDuplexValue = "ON"
else
set FullDuplexValue = "OFF"
endif
set CheckItemsIn = {$(EarlyTransmitValue),$(LinkIntegrityValue),$(FullDuplexValue),$(DirectEnableValue)}
;set CheckItemsIn = {"OFF", "ON", "OFF", "OFF"}
; Save the settings as they were read from the Registry.
; Shell $(ParamInf) Param_SaveValues
; Set CurrParamSettings = $($R0)
;
; Put up the adapter configuration dialog if necessary.
;
; Note that $(CurrParamSettings) has the old known parameter values.
;
adaptersetup = +
;Shell "" DebugConfiguration "before displaying dialog"
Set from = adapteroptions
adapteroptions = +
;If this is an unattend installation we need to skip the DLL UI stuff.
ifstr(i) $(!STF_GUI_UNATTENDED) == "YES"
goto skipoptions
endif
set CheckItemsIn = {$(EarlyTransmitValue),$(LinkIntegrityValue),$(FullDuplexValue),$(DirectEnableValue)}
LoadLibrary "disk 1" $(DialogDllName) hLib
read-syms FileDependentDlg$(!STF_LANGUAGE)"-"$(Option)
set ENABLER = 0
ifint $(RUNDLLCODE) == 1
LibraryProcedure ENABLER, $(hLib), EnablerRunning ; check for enabler type
ifint $(ENABLER) == 1
set Static1Label = "Configuring driver for Microsoft Enabler"
else-ifint $(ENABLER) == 2
set Static1Label = "Configuring driver for third party Card & Socket Services"
else
set Static1Label = "Configuring driver for Accton Enabler"
endif
endif
;------------------------------------------------------
; Call out to the PCMCIA driver only if we're loading a PCMCIA device
ifint $(RUNDLLCODE) == 1
; DLLCODE
; Locate the slot with the Accton Card in it
;------------------------------------------------------
LibraryProcedure CONFIG, $(hLib), GetPCMCIAConfig
set SLOTCOUNT = 8 ; was *($(CONFIG),1), but returned 0
set CONTROLLERTYPE = *($(CONFIG),3)
;Debug-Output "slot count="$(SLOTCOUNT)" controller type="$(CONTROLLERTYPE)
set SLOT = 0
slotloop = +
LibraryProcedure INFO, $(hLib), GetVERS_1Tuple $(SLOT) ;VERS_1
ifstr(i) *($(INFO),3) == $(VERS1Manufacturer)
ifstr(i) *($(INFO),4) == $(VERS1Product)
goto slotfound
endif
endif
set-add SLOT = $(SLOT), 1
ifint $(SLOT) == $(SLOTCOUNT)
goto slotnotfound
else
goto slotloop
endif
slotfound = +
;Debug-Output "EN2226 PC Card found in slot "$(SLOT)
;set Static2Label = "EN2226 PC Card in slot "$(SLOT)
LibraryProcedure INFO, $(hLib), GetFUNCETuple $(SLOT) ;VERS_1
set Static2Label = "Physical Address:"
set Static3Label = $(INFO)
ifstr(i) $(NetworkAddressValue) != ""
set Static4Label = "Network Address:"
set Static5Label = $(NetworkAddressValue)
endif
set SLOTFOUND = 1
goto slotcontinue
slotnotfound = +
set SLOTFOUND = ""
;set Static2Label = "EN2226 PC Card was not found"
;Debug-Output "EN2226 PC Card not found"
slotcontinue = +
endif
;------------------------------------------------------
ui start "InputDlg" $(hLib)
set ExitButton = $(ButtonPressed)
;Debug-Output " ButtonPressed "$(ButtonPressed)
;Debug-Output " DLGEVENT "$(DLGEVENT)
FreeLibrary $(hLib)
ifstr(i) $(DLGEVENT) == "CONTINUE"
set IOBaseAddrIndex = $(Combo1Out)
set MemoryAddrIndex = $(Combo2Out)
set IRQValueIndex = $(Combo3Out)
set ModeIndex = $(Combo4Out)
set CableTypeIndex = $(Combo5Out)
set LineSpeedIndex = $(Combo6Out)
set EarlyTransmitValue = *($(CheckItemsOut), 1)
set LinkIntegrityValue = *($(CheckItemsOut), 2)
set FullDuplexValue = *($(CheckItemsOut), 3)
set DirectEnableValue = *($(CheckItemsOut), 4)
set ExitButton = $(ButtonPressed)
ui pop 1
else-ifstr(i) $(DLGEVENT) == "EXIT"
set CommonStatus = STATUS_USERCANCEL
ui pop 1
goto end
else
set CommonStatus = STATUS_USERCANCEL
ui pop 1
Debug-Output "Action: unknown. Bye."
goto end
endif
;
; If installing, go create the necessary keys;
; if configuring, they're already open.
;
skipoptions =+
ifint $(OldVersionExisted) == $(TRUE)
ifstr(i) $(!NTN_InstallMode) == configure
goto writeparameters
endif
endif
StartWait
;
; Add Software Component
;
ifint $(OldVersionExisted) == $(FALSE)
ifstr(i) $(!NTN_InstallMode) == "install"
Ifstr(i) $(DoCopy) == "YES"
Shell $(UtilityInf), DoAskSource, $(!STF_CWDDIR), $(SrcDir) YES
Ifint $($ShellCode) != $(!SHELL_CODE_OK)
Goto ShellCodeError
Else-Ifstr(i) $($R0) == STATUS_FAILED
Shell $(UtilityInf) RegistryErrorString "ASK_SOURCE_FAIL"
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set Error = $($R0)
Goto fatal
Else-Ifstr(i) $($R0) == STATUS_USERCANCEL
Goto successful
Endif
Set SrcDir = $($R1)
Endif
install "Install-Option"
ifstr(i) $(STF_INSTALL_OUTCOME) != STF_SUCCESS
Shell $(UtilityInf) RegistryErrorString "UNABLE_COPY_FILE"
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set Error = $($R0)
goto fatal
endif
endif
Shell $(UtilityInf), AddSoftwareComponent, $(Manufacturer), +
$(ProductSoftwareName), +
$(ProductSoftwareName), +
$(ProductSoftwareTitle), $(STF_CONTEXTINFNAME), +
$(ProductSoftwareImagePath), "kernel", "NDIS", {}, "",+
$(NetEventDLL)
Set OEM_ABANDON_SOFTWARE = TRUE
ifint $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output "ShellCode error"
goto ShellCodeError
endif
;
; At this point:
; $R1 contains the product version key handle;
; $R2 contains the NetRules subkey handle;
; $R3 contains the new Services key handle; and
; $R4 contains the Parameters key
; $R5 contains the Linkage Key
;
set RegistryErrorIndex = $($R0)
set KeyProduct = $($R1)
Set SoftNetRulesKey = $($R2)
CloseRegKey $($R3)
CloseRegKey $($R4)
CloseRegKey $($R5)
Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
EndWait
Debug-Output "Registry error: add software components"
CloseRegKey $(KeyProduct)
CloseRegKey $(SoftNetRulesKey)
goto fatalregistry
endif
set NewValueList = {{SoftwareType,$(NoTitle),$(!REG_VT_SZ),$(SoftwareType)},+
{MajorVersion,$(NoTitle),$(!REG_VT_DWORD),$(ProductMajorVersion)},+
{MinorVersion,$(NoTitle),$(!REG_VT_DWORD),$(ProductMinorVersion)},+
{Title,$(NoTitle),$(!REG_VT_SZ),$(ProductSoftwareTitle)},+
{Description,$(NoTitle),$(!REG_VT_SZ),$(ProductSoftwareDescription)},+
{ServiceName,$(NoTitle),$(!REG_VT_SZ),$(ProductSoftwareName)},+
{InstallDate,$(NoTitle),$(!REG_VT_DWORD),*($(Now),1)}}
Shell $(UtilityInf), AddValueList, $(KeyProduct), $(NewValueList)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output "ShellCode error."
goto ShellCodeError
endif
set RegistryErrorIndex = $($R0)
Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
EndWait
Debug-Output "Registry error: add value list."
CloseRegKey $(KeyProduct)
CloseRegKey $(SoftNetRulesKey)
goto fatalregistry
endif
set NewValueList = {{type,$(NoTitle),$(!REG_VT_SZ),$(NetRuleSoftwareType)},+
{use,$(NoTitle),$(!REG_VT_SZ),$(NetRuleSoftwareUse)}, +
{bindform,$(NoTitle),$(!REG_VT_SZ),$(NetRuleSoftwareBindForm)}, +
{class,$(NoTitle),$(!REG_VT_MULTI_SZ),$(NetRuleSoftwareClass)}, +
{bindable,$(NoTitle),$(!REG_VT_MULTI_SZ),$(NetRuleSoftwareBindable)}, +
{InfOption,$(NoTitle),$(!REG_VT_SZ),$(Option)}}
Shell $(UtilityInf), AddValueList, $(SoftNetRulesKey), $(NewValueList)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output "ShellCode error."
goto ShellCodeError
endif
set RegistryErrorIndex = $($R0)
CloseRegKey $(KeyProduct)
CloseRegKey $(SoftNetRulesKey)
Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
EndWait
Debug-Output "Resgitry error: add value list."
goto fatalregistry
endif
endif
;
; Create the HARDWARE\Netcard region and its corresponding service
;
Shell $(UtilityInf), AddHardwareComponent, $(ProductHardwareName),$(STF_CONTEXTINFNAME),$(ProductKeyName)
ifint $($R4) != -1
Set OEM_ABANDON_OPTIONS = >($(OEM_ABANDON_OPTIONS), $(!NTN_SoftwareBase)"\Microsoft\Windows NT\CurrentVersion\NetworkCards\"$($R4))
endif
ifint $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output "Cannot add hardware component"
goto ShellCodeError
endif
set RegistryErrorIndex = $($R0)
Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
EndWait
Debug-Output "Registry error: add hardware component"
CloseRegKey $($R1)
CloseRegKey $($R2)
CloseRegKey $($R3)
goto fatalregistry
endif
;
; At this point:
; $R1 Registry key variable for HARDWARE\Netcard\(n)
; $R2 Registry key variable for HARDWARE\Netcard\(n)\\NetRules
; $R3 Registry key handle for <service>\Parameters key
; $R4 Adapter number assigned to adapter
; $R5 Service name generated by combining svc name with adapter number
;
set KeyParameters = $($R3)
set KeyAdapterRules = $($R2)
set AdapterNumber = $($R4)
set NewValueList = {{Manufacturer,$(NoTitle),$(!REG_VT_SZ),$(Manufacturer)},+
{Title,$(NoTitle),$(!REG_VT_SZ),"["$($R4)"] "$(ProductHardwareTitle)},+
{Description,$(NoTitle),$(!REG_VT_SZ),$(ProductHardwareDescription)},+
{ProductName,$(NoTitle),$(!REG_VT_SZ),$(ProductHardwareName)},+
{ServiceName,$(NoTitle),$(!REG_VT_SZ),$($R5)},+
{InstallDate,$(NoTitle),$(!REG_VT_DWORD),*($(Now),1)}}
Shell $(UtilityInf), AddValueList, $($R1), $(NewValueList)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output "ShellCode error"
goto ShellCodeError
endif
CloseRegKey $($R1)
set TempProdName = """"$(ProductHardwareName)$(AdapterNumber)""""
set TempBindForm = $(TempProdName)$(NetRuleHardwareBindForm)
set NewValueList = {{type,$(NoTitle),$(!REG_VT_SZ),$(NetRuleHardwareType)},+
{bindform,$(NoTitle),$(!REG_VT_SZ),$(TempBindForm)}, +
{class,$(NoTitle),$(!REG_VT_MULTI_SZ),$(NetRuleHardwareClass)}, +
{InfOption,$(NoTitle),$(!REG_VT_SZ),$(Option)}}
Shell $(UtilityInf), AddValueList, $(KeyAdapterRules), $(NewValueList)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output "ShellCode error."
goto ShellCodeError
endif
set RegistryErrorIndex = $($R0)
Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
EndWait
Debug-Output "Resgitry error: add value list."
CloseRegKey $(KeyParameters)
CloseRegKey $(KeyAdapterRules)
goto fatalregistry
endif
CloseRegKey $(KeyAdapterRules)
goto writeparameters
;
; REQUIRED: $(KeyParameters) contains service Parameters key handle
;
writeparameters = +
Shell $(UtilityInf), GetBusTypeNum
; set BusTypeNum = $($R1)
set BusTypeNum = 1
ifint $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output "ShellCode error."
goto ShellCodeError
endif
;
; Add the rest of the parameters to the Services area
;
ifstr(i) $(EarlyTransmitValue) == "ON"
set EarlyTransmitValue = "1"
else
set EarlyTransmitValue = "0"
endif
ifstr(i) $(DirectEnableValue) == "ON"
set DirectEnableValue = "1"
set PcmciaValue = "0"
else
set DirectEnableValue = "0"
set PcmciaValue = "1"
endif
ifstr(i) $(LinkIntegrityValue) == "ON"
set LinkIntegrityValue = "1"
else
set LinkIntegrityValue = "0"
endif
ifstr(i) $(FullDuplexValue) == "ON"
set FullDuplexValue = "1"
else
set FullDuplexValue = "0"
endif
ifstr(i) $(!STF_GUI_UNATTENDED) == "YES"
set ModeValue = *($(ModeValues), 1)
set MemoryAddrValue = *($(MemoryAddrValues), 53)
set-add CommonMemoryAddrValue = $(MemoryAddrValue), 4096
set IRQValue = *($(IRQValues), 3)
set IOBaseAddrValue = *($(IOBaseAddrValues), 16)
set CableTypeValue = *($(CableTypeValues), 1)
set LineSpeedValue = *($(LineSpeedValues), 1)
set IOLengthValue = 15
else
set ModeValue = *($(ModeValues), ~($(ModeList), $(ModeIndex)))
set MemoryAddrValue = *($(MemoryAddrValues),~($(MemoryAddrList), $(MemoryAddrIndex)))
set-add CommonMemoryAddrValue = $(MemoryAddrValue), 4096
set IRQValue = *($(IRQValues), ~($(IRQList), $(IRQValueIndex)))
set IOBaseAddrValue = *($(IOBaseAddrValues),~($(IOBaseAddrList), $(IOBaseAddrIndex)))
set CableTypeValue = *($(CableTypeValues), ~($(CableTypeList), $(CableTypeIndex)))
set LineSpeedValue = *($(LineSpeedValues), ~($(LineSpeedList), $(LineSpeedIndex)))
set IOLengthValue = 15
endif
set NewValueList = {{AdapterType, $(NoTitle),$(!REG_VT_DWORD),0},+
{BusNumber, $(NoTitle),$(!REG_VT_DWORD),0},+
{BusType, $(NoTitle),$(!REG_VT_DWORD),$(BusTypeNum)},+
{CableType, $(NoTitle),$(!REG_VT_DWORD),$(CableTypeValue)},+
{DirectEnable, $(NoTitle),$(!REG_VT_DWORD),$(DirectEnableValue)},+
{EarlyTransmit, $(NoTitle),$(!REG_VT_DWORD),$(EarlyTransmitValue)},+
{FullDuplex, $(NoTitle),$(!REG_VT_DWORD),$(FullDuplexValue)},+
{InterruptNumber, $(NoTitle),$(!REG_VT_DWORD),$(IRQValue)},+
{IoBaseAddress, $(NoTitle),$(!REG_VT_DWORD),$(IOBaseAddrValue)},+
{IoLength, $(NoTitle),$(!REG_VT_DWORD), 15},+
{LineSpeed, $(NoTitle),$(!REG_VT_DWORD),$(LineSpeedValue)},+
{LinkIntegrity, $(NoTitle),$(!REG_VT_DWORD),$(LinkIntegrityValue)},+
{MemoryMappedBaseAddress, $(NoTitle),$(!REG_VT_DWORD),$(CommonMemoryAddrValue)},+
{MemoryMappedSize, $(NoTitle),$(!REG_VT_DWORD),4096},+
{Mode, $(NoTitle),$(!REG_VT_DWORD),$(ModeValue)},+
{PCCARDAttributeMemoryAddress, $(NoTitle),$(!REG_VT_DWORD),$(MemoryAddrValue)},+
{PCCARDAttributeMemoryOffset, $(NoTitle),$(!REG_VT_DWORD),0},+
{PCCARDAttributeMemorySize, $(NoTitle),$(!REG_VT_DWORD),4096},+
{PCCARDMemoryWindowOffset, $(NoTitle),$(!REG_VT_DWORD),0},+
{PCMCIA, $(NoTitle),$(!REG_VT_DWORD),$(PcmciaValue)},+
{TransmitBufferSize, $(NoTitle),$(!REG_VT_DWORD),7168}}
Shell $(UtilityInf), AddValueList, $(KeyParameters), $(NewValueList)
ifstr(i) $(!STF_GUI_UNATTENDED) == "YES"
Shell $(UtilityInf), AddDefaultNetCardParameters, $(KeyParameters)
endif
CloseRegKey $(KeyParameters)
; --------------------------------------------------------------------------------
; Reprogram the PCMCIA slot with the new parameters
; Should only be done during first time installation of NT, and if Accton card was found
; --------------------------------------------------------------------------------
; Call out to the PCMCIA driver only if we're loading a PCMCIA device
ifint $(RUNDLLCODE) == 1
ifint $(ENABLER) == 1
ifint $(HOTPROGRAMPCMCIA) == 1
ifint $(SLOTFOUND) == 1 ; and a Accton card was found in a slot
LoadLibrary "disk 1" $(DialogDllName) hLib
Debug-Output "Enabling network resources"
ifstr(i) $(Option) == CM2NDIS3
LibraryProcedure STATUS, $(hLib), SetupSlot $(SLOT) 0 $(IRQValue) $(IOBaseAddrValue) $(IOLengthValue) $(MemoryAddrValue) 4096 0
else
LibraryProcedure STATUS, $(hLib), SetupSlot $(SLOT) $(IRQValue) 0 $(IOBaseAddrValue) $(IOLengthValue) $(MemoryAddrValue) 4096 0
endif
Debug-Output "SetupSlot: "$(STATUS)
FreeLibrary $(hLib)
endif
endif
endif
endif
; --------------------------------------------------------------------------------
; Write the parameters to the PCMCIA database section, iff running MS Enabler
; Add/replace only the parts for the EN2226
; --------------------------------------------------------------------------------
set PCMCIADatabaseKeyName = $(!NTN_ServiceBase)"\Pcmcia\DataBase"
set PCMCIADatabaseOEMKeyName = $(PCMCIADatabaseKeyName)"\Accton"
OpenRegKey $(!REG_H_LOCAL) "" $(PCMCIADatabaseKeyName) $(MAXIMUM_ALLOWED) PCMCIADatabaseKey
ifstr $(PCMCIADatabaseKey) == $(NULL)
;Debug-Output "Pcmcia\DataBase not present"
else ; PCMCIA.sys is installed and registry has database section in it.
; Try to open Accton section.
OpenRegKey $(!REG_H_LOCAL) "" $(PCMCIADatabaseKeyName)"\Accton" $(MAXIMUM_ALLOWED) PCMCIADatabaseOEMKey
ifstr $(PCMCIADatabaseOEMKey) == $(NULL) ; open failed, so create Accton subkey
CreateRegKey $(PCMCIADatabaseKey) {"Accton", 0, 0} "" $(MAXIMUM_ALLOWED) "" PCMCIADatabaseOEMKey
endif
; Open $(VERS1Product) key ----------------------------------------------------------------------
OpenRegKey $(!REG_H_LOCAL) "" $(PCMCIADatabaseOEMKeyName)"\"$(VERS1Product) $(MAXIMUM_ALLOWED) PCMCIADatabaseEN2226Key
ifstr $(PCMCIADatabaseEN2226Key) == $(NULL)
CreateRegKey $(PCMCIADatabaseOEMKey) {$(VERS1Product), 0, 0} "" $(MAXIMUM_ALLOWED) 0 PCMCIADatabaseEN2226Key
endif
; Set the values --------------------------------------------------------------------------------------
SetRegValue $(PCMCIADatabaseEN2226Key) {Driver, 0, $(!REG_VT_SZ),"en2226"}
SetRegValue $(PCMCIADatabaseEN2226Key) {AttributeMemorySize, 0, $(!REG_VT_DWORD),4096}
SetRegValue $(PCMCIADatabaseEN2226Key) {DeviceType, 0, $(!REG_VT_SZ),"NET"}
CloseRegKey $(PCMCIADatabaseEN2226Key)
CloseRegKey $(PCMCIADatabaseOEMKey)
CloseRegKey $(PCMCIADatabaseKey)
endif
; --------------------------------------------------------------------------------
; --------------------------------------------------------------------------------
ifint $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output "ShellCode error."
goto ShellCodeError
endif
set RegistryErrorIndex = $($R0)
Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
Debug-Output "Registry error: Add value list"
goto fatalregistry
endif
EndWait
goto successful
;-----------------------------------------------
; Binding section
;-----------------------------------------------
bindingadapter =+
set Error = "Binding: Sorry, not yet implemented."
goto fatal
;-----------------------------------------------
; Removeadapter section
;-----------------------------------------------
removeadapter = +
Ifstr(i) $(ProductKeyName) == $(!NTN_RegBase)
; Remove Software Component
Shell $(UtilityInf), RemoveSoftwareComponent, $(Manufacturer), +
$(ProductSoftwareName)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output "ShellCode error"
goto ShellCodeError
endif
set RegistryErrorIndex = $($R0)
Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
goto fatalregistry
endif
else
Shell $(UtilityInf), RemoveHardwareComponent, $(Manufacturer), +
$(ProductSoftwareName), $(!NTN_RegBase)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output "ShellCode error"
goto ShellCodeError
endif
set RegistryErrorIndex = $($R0)
Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
goto fatalregistry
endif
endif
goto end
;-----------------------------------------------
; Upgrade Software section
;-----------------------------------------------
UpgradeSoftware = +
;
; First determine whether we want to do upgrade or update for software
; or hardware component. Then we will determine whether the Mode is
; update or upgrade.
;
; If the same version of the product existed in the registry, we do
; update. Otherwise, we will do a upgrade
;
ifstr(i) $(ProductKeyName) == $(!NTN_RegBase)
; Upgrade software component
;
; see whether the same version exist or not
;
OpenRegKey $(!REG_H_LOCAL) "" $(ProductKeyName) $(MAXIMUM_ALLOWED) KeyProduct
Ifstr $(KeyProduct) != $(KeyNull)
GetRegValue $(KeyProduct),"MajorVersion", VersionInfo
set Version = *($(VersionInfo), 4)
;
; Update the binaries
;
Shell $(UtilityInf), GetInfFileNameFromRegistry, $(KeyProduct)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output "ShellCode error"
goto ShellCodeError
endif
set !UG_Filename = $($R0)
ifstr(i) $(!UG_Filename) != ""
install "Install-Update"
ifstr(i) $(STF_INSTALL_OUTCOME) != STF_SUCCESS
goto fatal
endif
endif
; Upgrade the version number
;
SetRegValue $(KeyProduct) {MajorVersion,$(NoTitle),$(!REG_VT_SZ),$(ProductMajorVersion)}
SetRegValue $(KeyProduct) {MinorVersion,$(NoTitle),$(!REG_VT_SZ),$(ProductMinorVersion)}
;
; do nothing for update
;
ifint $(Version) != $(ProductVersion)
;
; If the major version number is not the same,
; it is major upgrade. So let Upgrade the product
;
;
; make other upgrade change if necessary
;
endif
CloseRegKey $(KeyProduct)
else
;
; Cannot Open software key, goto ERROR
;
goto fatalregistry
endif
else
;
; upgrade/update hardware component
; There is no different between upgrade and update for hardware
; component
;
; 1. Get the Service Name
; 2. Change the NetRule section if necessary
;
OpenRegKey $(!REG_H_LOCAL) "" $(!NTN_RegBase) +
$(MAXIMUM_ALLOWED) NetworkCardKey
Ifstr(i) $(NetworkCardKey) != $(KeyNull)
;
; Get Service name
;
GetRegValue $(NetworkCardKey),"ServiceName", ServiceNameInfo
set ServiceName = *($(ServiceNameInfo), 4)
;
; Change the NetRule if necessary
;
OpenRegKey $(NetworkCardKey) "" "NetRules" +
$(MAXIMUM_ALLOWED) NetRuleKey
Ifstr(i) $(NetRuleKey) != $(KeyNull)
;
; Make the change....
;
else
;
; Error, cannot open net rules key
;
goto fatalregistry
endif
CloseRegKey $(NetRules)
CloseRegKey $(NetworkCardKey)
else
;
; Error, cannot open network card key
;
goto fatalregistry
endif
;
; 3. Change the service section of the hardware. i.e.,
; ParameterName change, value change, etc.
;
OpenRegKey $(!REG_H_LOCAL) "" +
$(!NTN_ServiceBase)"\"$(ServiceName) +
$(MAXIMUM_ALLOWED) ServiceKey
Ifstr(i) $(ServiceKey) != $(KeyNull)
;
; Get the ServiceKey to change the Start value
; or Type value. Or open Parameters key to
; change the hardware parameters if necessary.
;
CloseRegKey $(ServiceKey)
else
;
; Error, cannot open network card key
;
goto fatalregistry
endif
endif
goto end
;
; End of Upgrade Software
;
;
; Escape hatches
;
successful = +
goto end
abandon = +
ForListDo $(OEM_ABANDON_OPTIONS)
Shell $(UtilityInf), RemoveHardwareComponent, $(Manufacturer), +
$(ProductSoftwareName), $($)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output "ShellCode error"
goto ShellCodeError
endif
set RegistryErrorIndex = $($R0)
Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
goto fatalregistry
endif
EndForListDo
Ifstr(i) $(OEM_ABANDON_SOFTWARE) == TRUE
; Remove Software Component
Shell $(UtilityInf), RemoveSoftwareComponent, $(Manufacturer), +
$(ProductSoftwareName), FALSE
ifint $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output "ShellCode error"
goto ShellCodeError
endif
set RegistryErrorIndex = $($R0)
Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
goto fatalregistry
endif
endif
goto end
;
; warning display
;
warning = +
Shell $(subroutineinf) SetupMessage, $(!STF_LANGUAGE), "WARNING", $(Error)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
ifstr(i) $($R1) == "OK"
goto $(to)
else-ifstr(i) $($R1) == "CANCEL"
goto $(from)
else
goto "end"
endif
;
; non fatal error display
;
nonfatalinfo = +
Set Severity = STATUS
Set CommonStatus = STATUS_USERCANCEL
goto nonfatalmsg
nonfatal = +
Set Severity = NONFATAL
goto nonfatalmsg
nonfatalmsg = +
ifstr(i) $(Error) == ""
Set Severity = NONFATAL
Shell $(UtilityInf) RegistryErrorString "SETUP_FAIL"
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set Error = $($R0)
endif
Shell $(subroutineinf) SetupMessage, $(!STF_LANGUAGE), $(Severity), $(Error)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
ifstr(i) $($R1) == "OK"
goto $(from)
else
goto "end"
endif
;
; Registry is broken
;
fatalregistry = +
Shell $(UtilityInf) RegistryErrorString $(RegistryErrorIndex)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set Error = $($R0)
goto fatal
;
; Netcard detection failure
;
fataldetect = +
Shell $(UtilityInf),RegistryErrorString,CANNOT_DETECT
ifint $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output "ShellCode error: cannot get an error string."
goto ShellCodeError
endif
set Error = $($R0)
Goto fatal
;
; fatal error display
;
fatal = +
ifstr(i) $(Error) == ""
Shell $(UtilityInf) RegistryErrorString "SETUP_FAIL"
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set Error = $($R0)
endif
Shell $(subroutineinf) SetupMessage, $(!STF_LANGUAGE), "FATAL", $(Error)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
goto setfailed
;
; Shelling error
;
ShellCodeError = +
set DlgType = "MessageBox"
set STF_MB_TITLE = $(ShellCodeErrorTitle)
set STF_MB_TEXT = $(ShellCodeErrorText)
set STF_MB_TYPE = 1
set STF_MB_ICON = 3
set STF_MB_DEF = 1
ui start "Error Message"
goto setfailed
setfailed = +
set CommonStatus = STATUS_FAILED
;
; if OEM_ABANDON_ON == TRUE, then remove the registry entries
;
ifstr(i) $(OEM_ABANDON_ON) == TRUE
set OEM_ABANDON_ON = FALSE
goto abandon
endif
goto end
end = +
goto term
term = +
Return $(CommonStatus)
[DebugConfiguration]
Set InfName = "OEMSETNT.INF"
;Debug-Output $(InfName)" **CONFIGURATION STATE: "$($0)
;Debug-Output $(InfName)" IRQ_Level is "$(!p:IRQ_Level)
;Debug-Output $(InfName)" IOBaseAddrValue is "$(!p:IOBaseAddrValue)
;Debug-Output $(InfName)" TransceiverValue is "$(!p:TransceiverValue)
;Debug-Output $(InfName)" MemoryAddr is "$(!p:MemoryAddr)
;Debug-Output $(InfName)" MappedValue is "$(!p:MappedValue)
return
;***************************************************************
; INSTALL SECTIONS
;***************************************************************
[Install-Option]
set STF_VITAL = ""
ifstr(i) $(AddCopy) == "YES"
AddSectionFilesToCopyList Files-$(Option) $(SrcDir) $(!STF_WINDOWSSYSPATH)\drivers
endif
ifstr(i) $(DoCopy) == "YES"
;
; Copy files in the copy list
;
set !STF_NCPA_FLUSH_COPYLIST = TRUE
CopyFilesInCopyList
endif
Exit
[Install-Update]
set STF_VITAL = ""
set STF_OVERWRITE = "VERIFYSOURCEOLDER"
;set STF_VERSION = "YES"
AddSectionFilesToCopyList Files-$(Option) $(SrcDir) $(!STF_WINDOWSSYSPATH)\drivers
AddSectionFilesToCopyList Files-Inf $(SrcDir) $(!STF_WINDOWSSYSPATH)
set !STF_NCPA_FLUSH_COPYLIST = TRUE
CopyFilesInCopyList
exit
[Install-Dll]
set STF_VITAL = ""
AddSectionFilesToCopyList Files-Dll $(SrcDir) $(!STF_WINDOWSSYSPATH)
set !STF_NCPA_FLUSH_COPYLIST = TRUE
CopyFilesInCopyList
exit
[Source Media Descriptions]
1 = "Accton Setup Disk for NT"
[ProductType]
STF_PRODUCT = Winnt
STF_PLATFORM = I386
[Files-Inf]
1, OEMSETNT.INF, SIZE=58000, RENAME=$(!UG_Filename)
[Files-Dll]
1, EN2226.DLL, SIZE=21000
[Files-EN2226]
1, EN2226.SYS, SIZE=53000
[LanguagesSupported]
ENG
[AllFileConstantsENG]
ProCaption = "Windows NT Setup"
ProCancel = "Cancel"
ProCancelMsg = "Windows NT Networking is not correctly installed. "+
"Are you sure you want to cancel copying files?"
ProCancelCap = "Network Setup Message"
ProText1 = "Copying:"
ProText2 = "To:"
DialogDllName = "EN2226.DLL"
; START EN2226 -------------------------------------------------------------------------------------------
[FileConstantsENG-EN2226]
FunctionTitle = $(GenericTitleName)" Setup"$(GenericInfVersion)
ProductSoftwareTitle = $(GenericDriverName)
ProductHardwareTitle = $(GenericAdapterName)
IRQList = ^(IRQChoices, 1)
IRQValues = ^(IRQChoices, 2)
IOBaseAddrList = ^(IOBaseAddrChoices, 1)
IOBaseAddrValues = ^(IOBaseAddrChoices, 2)
MemoryAddrList = ^(MemoryAddrChoices,1)
MemoryAddrValues = ^(MemoryAddrChoices,2)
CableTypeList = ^(CableTypeChoices, 1)
CableTypeValues = ^(CableTypeChoices, 2)
ModeList = ^(ModeChoices, 1)
ModeValues = ^(ModeChoices, 2)
LineSpeedList = ^(LineSpeedChoices, 1)
LineSpeedValues = ^(LineSpeedChoices, 2)
[DialogConstantsENG-EN2226]
Help = "&Help"
Exit = "Cancel"
OK = "OK"
HelpContext = ""
Continue = "Continue"
Cancel = "Cancel"
[FileDependentDlgENG-EN2226]
DlgType = "RadioCombination"
DlgTemplate = "CE3"
Caption = $(FunctionTitle)
HelpContext = $(!IDH_DB_OEMNADE2_INS)
CBOptionsGreyed = {}
NotifyFields = {NO, NO, NO, NO, NO, NO, NO, NO}
Combo1Label = "I/&O Port:"
Combo2Label = "&Memory Address:"
Combo3Label = "&Interrupt:"
Combo4Label = "Mo&de:"
Combo5Label = "&Cable Type:"
Combo6Label = "&Line Speed:"
Check1 = "&Early Transmit"
Check2 = "&Link Integrity"
Check3 = "&Full Duplex"
Check4 = "Di&rect Enable"
Combo1List = $(IOBaseAddrList)
Combo1Out = $(IOBaseAddrValue)
Combo2List = $(MemoryAddrList)
Combo2Out = $(MemoryAddrValue)
Combo3List = $(IRQList)
Combo3Out = $(IRQValue)
Combo4List = $(ModeList)
Combo4Out = $(ModeValue)
Combo5List = $(CableTypeList)
Combo5Out = $(CableTypeValue)
Combo6List = $(LineSpeedList)
Combo6Out = $(LineSpeedValue)
ComboListItemsIn = {Combo1List,Combo2List,Combo3List, Combo4List, Combo5List, Combo6List}
ComboListItemsOut = {Combo1Out, Combo2Out, Combo3Out, Combo4Out, Combo5Out, Combo6Out}
CheckItemsIn = {$(EarlyTransmitValue),$(LinkIntegrityValue),$(FullDuplexValue),$(DirectEnableValue)}
CheckItemsOut = {Check1Out, Check2Out, Check3Out, Check4Out}
EditTextIn = {"",""}
EditTextLim = {"",""}
; END EN2226 -------------------------------------------------------------------------------------------
[MemoryAddrChoices]
MA_1 = "0xA0000", 655360
MA_2 = "0xA1000", 659456
MA_3 = "0xA2000", 663552
MA_4 = "0xA3000", 667648
MA_5 = "0xA4000", 671744
MA_6 = "0xA5000", 675840
MA_7 = "0xA6000", 679936
MA_8 = "0xA7000", 684032
MA_9 = "0xA8000", 688128
MA_10 = "0xA9000", 692224
MA_11 = "0xAA000", 696320
MA_12 = "0xAB000", 700416
MA_13 = "0xAC000", 704512
MA_14 = "0xAD000", 708608
MA_15 = "0xAE000", 712704
MA_16 = "0xAF000", 716800
MA_17 = "0xB0000", 720896
MA_18 = "0xB1000", 724992
MA_19 = "0xB2000", 729088
MA_20 = "0xB3000", 733184
MA_21 = "0xB4000", 737280
MA_22 = "0xB5000", 741376
MA_23 = "0xB6000", 745472
MA_24 = "0xB7000", 749568
MA_25 = "0xB8000", 753664
MA_26 = "0xB9000", 757760
MA_27 = "0xBA000", 761856
MA_28 = "0xBB000", 765952
MA_29 = "0xBC000", 770048
MA_30 = "0xBD000", 774144
MA_31 = "0xBE000", 778240
MA_32 = "0xBF000", 782336
MA_33 = "0xC0000", 786432
MA_34 = "0xC1000", 790528
MA_35 = "0xC2000", 794624
MA_36 = "0xC3000", 798720
MA_37 = "0xC4000", 802816
MA_38 = "0xC5000", 806912
MA_39 = "0xC6000", 811008
MA_40 = "0xC7000", 815104
MA_41 = "0xC8000", 819200
MA_42 = "0xC9000", 823296
MA_43 = "0xCA000", 827392
MA_44 = "0xCB000", 831488
MA_45 = "0xCC000", 835584
MA_46 = "0xCD000", 839680
MA_47 = "0xCE000", 843776
MA_48 = "0xCF000", 847872
MA_49 = "0xD0000", 851968
MA_50 = "0xD1000", 856064
MA_51 = "0xD2000", 860160
MA_52 = "0xD3000", 864256
MA_53 = "0xD4000", 868352
MA_54 = "0xD5000", 872448
MA_55 = "0xD6000", 876544
MA_56 = "0xD7000", 880640
MA_57 = "0xD8000", 884736
MA_58 = "0xD9000", 888832
MA_59 = "0xDA000", 892928
MA_60 = "0xDB000", 897024
MA_61 = "0xDC000", 901120
MA_62 = "0xDD000", 905216
MA_63 = "0xDE000", 909312
MA_64 = "0xDF000", 913408
MA_65 = "0xE0000", 917504
MA_66 = "0xE1000", 921600
MA_67 = "0xE2000", 925696
MA_68 = "0xE3000", 929792
MA_69 = "0xE4000", 933888
MA_70 = "0xE5000", 937984
MA_71 = "0xE6000", 942080
MA_72 = "0xE7000", 946176
MA_73 = "0xE8000", 950272
MA_74 = "0xE9000", 954368
MA_75 = "0xEA000", 958464
MA_76 = "0xEB000", 962560
MA_77 = "0xEC000", 966656
MA_78 = "0xED000", 970752
MA_79 = "0xEE000", 974848
MA_80 = "0xEF000", 978944
MA_81 = "0xF0000", 983040
MA_82 = "0xF1000", 987136
MA_83 = "0xF2000", 991232
MA_84 = "0xF3000", 995328
MA_85 = "0xF4000", 999424
MA_86 = "0xF5000", 1003520
MA_87 = "0xF6000", 1007616
MA_88 = "0xF7000", 1011712
MA_89 = "0xF8000", 1015808
MA_90 = "0xF9000", 1019904
MA_91 = "0xFA000", 1024000
MA_92 = "0xFB000", 1028096
MA_93 = "0xFC000", 1032192
MA_94 = "0xFD000", 1036288
MA_95 = "0xFE000", 1040384
[IRQChoices]
;Interrupts available on the PCIC: { 3,4,5,7,8,10,11,12,14,15 }
;Interrupts available on the TCIC: { 3,4,5,6,7,10,14 }
;14 = fixed disk
;12 = keyboard
;6 = floppy disk
;union(PCIC, TCIC) - {14} = 3,4,5,7,10
IRQ_1 = "3",3
IRQ_2 = "4",4
IRQ_3 = "5",5
IRQ_4 = "7",7
IRQ_5 = "10",10
IRQ_6 = "11",11
IRQ_7 = "15",15
[ModeChoices]
MO_1 = "I/O", 0
MO_2 = "Memory Mapped", 1
[CableTypeChoices]
CT_1 = "Auto Detect", 0
CT_2 = "Twisted Pair - 10BT", 1
[LineSpeedChoices]
LS_1 = "Auto Detect", 0
LS_2 = "10 Mbps", 1
LS_3 = "100 Mbps", 2
[IOBaseAddrChoices]
; 0x3E0 is where PCIC is located
; 0x240 is where TCIC is located
; therefore user cannot select these for locating the ethernet adapter
IOBase_1 = "0x200",512
IOBase_2 = "0x210",528
IOBase_3 = "0x220",544
IOBase_4 = "0x230",560
;IOBase_5 = "0x240",576
IOBase_6 = "0x250",592
IOBase_7 = "0x260",608
IOBase_8 = "0x270",624
IOBase_9 = "0x280",640
IOBase_10 = "0x290",656
IOBase_11 = "0x2A0",672
IOBase_12 = "0x2B0",698
IOBase_13 = "0x2C0",714
IOBase_14 = "0x2D0",730
IOBase_15 = "0x2E0",746
IOBase_16 = "0x2F0",752
IOBase_17 = "0x300",768
IOBase_18 = "0x310",784
IOBase_19 = "0x320",800
IOBase_20 = "0x330",816
IOBase_21 = "0x340",832
IOBase_22 = "0x350",848
IOBase_23 = "0x360",864
IOBase_24 = "0x370",880
IOBase_25 = "0x380",896
IOBase_26 = "0x390",912
IOBase_27 = "0x3A0",928
IOBase_28 = "0x3B0",944
IOBase_29 = "0x3C0",960
IOBase_30 = "0x3D0",976
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.