Accton SmartEnabler Installation
FOR UNIXWARE & SCO UNIX
History:
1/25/95 v 1.0.1
1. Add the code to the SCO custom installation script to
allow a user to select the NAT0 LAN IO port and IRQ
if the NAT0 (NE2000) driver is NOT yet installed or
configured.
2. Add to the installation script the prompt to
allow a user to select Y/N to relink the kernel.
3. Include the prompt
"PCMCIA LAN Card was ..."
5/4/1995 v 1.0.3
1. SmartEnabler is now support UnixWare 1.1 as well as 2.0.
README.TXT This file
Installation procedure file
UNWLSEN.TAR Accton SmartEnabler driver UnixWare UNIX tar format
SCOLSEN.TAR Accton SmartEnabler driver for SCO UNIX tar format
CONTENTS
ÄÄÄÄÄÄÄÄÄÄÄÄ
1.0 Installation for UnixWare SVR4.2
1.1 Install the SmartEnabler
1.2 Remove the SmartEnabler
2.0 Installation for SCO UNIX SVR3.2
2.1 Install the SmartEnabler
2.2 Remove the SmartEnabler
3.0 Installation for SCO & UnixWare Enabler
from tar file
Appendix A: Configure the NE2K drivers
for UNIXWARE.
Configure UNIXWARE NE2K driver
Apendix B: Configure the NE2K drivers
for SCO UNIX.
Configure SCO NAT (NE2K) driver
INSTALLATION FOR UNIXWARE SVR4.2
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
1.0 Installation for UnixWare
1.1 Install the SmartEnabler
To install the Accton SmartEnabler for UnixWare
a user needs to do the following:
Insert the Accton SmartEnabler for UnixWare diskette
in floppy drive 0 and type the following command
to add the package to UNIXWARE:
pkgadd -d/dev/dsk/f03dt <Enter>
Next, select the go option to allow the installation utility
of UnixWare to process the package. Wait until the
installation process completes and then shutdown (reboot) the
system to allow the new driver to run.
ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³ NOTE: ³
³ The Enabler requires a LAN card to be in place or plugged ³
³ into a PCMCIA slot before booting the UnixWare. This version ³
³ of the driver is only a virtual device driver, it is not a ³
³ Socket Service or Generic enabler. Until Accton releases ³
³ the Socket Service driver the user must follow this advice ³
³ to make the LAN card work under UnixWare. ³
³ ³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
1.2 Remove the SmartEnabler
To remove the SmardEnabler from UnixWare SVR4.2, a user needs to
do the following:
1.2.1 Logon as root and at the # prompt type:
Pkgrm lsen <Enter>
The user should see the following message:
ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³ lsen Accton SmardEnabler Driver Package v1.0.2 ³
³ (i386)1.0.2 ³
³ ³
³ Do you want to remove this package [y.n.?.q]_ ³
³ ³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
1.2.2 The user should type:
"y" <Enter>
Next the system informs the user that the package is being removed
and updating system information. Finially, the user should see the
following massages on the screen if the package is removed successfully:
ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³ Removal of <lsen> was successful. ³
³ ³
³ *** IMPORTANT *** ³
³ ³
³ If removal of all desired packages is complete, the ³
³ machine should be rebooted in order to ensure sane ³
³ operation. Execute the shutdown command with the ³
³ appropriate options and wait for the "Console Login:" ³
³ prompt ³
³ ³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
1.2.3 Finally the user should reboot the system to allow the
new kernel to take effect.
2.0 Installation For SCO UNIX/ODT
2.1 Install the SmartEnabler
To install the Accton SmartEnabler for the SCO UNIX System V
Release 3.2 or SCO Open Desktop, a user needs to follow
these steps:
2.1.1 After system is bootup login as root.
2.1.2 Insert the Accton SmartEnabler for SCO UNIX/ODT diskette
into drive 0 (or drive A).
2.1.3 Type the following command
custom -m/dev/rfd096ds9 <Enter>
2.1.4 Select "Install" and press <Enter>
2.1.5 Select "A New Product" and press <Enter>
2.1.6 Select "Entire product" and press <Enter>
2.1.7 When prompted, the user inserts the Accton
SmartEnabler V1.0.2 in the proper drive.
Next the user should select "continue" and press <Enter>
2.1.8 Wait until the kernel rebuild to complete.
2.1.9 The System should prompt the user as follows:
ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³ Do you want this kernel to boot by default(y/n)_ ³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
2.1.10 Type "y" and press <Enter>
2.1.11 System should prompt the user as follows:
ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³ Do you want this kernel environment rebuit(y/n)_ ³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
2.1.12 Select "y" and press <Enter>
2.2 Remove the SmardEnabler
To remove the SmartEnabler driver from the SCO UNIX/ODT, a user
needs to do the following:
2.2.1 Make sure the user is in supper user mode and type:
Custom <Enter>
2.2.2 Select the Remove option from the custom menu and press
<Enter>
2.2.3 Select the Accton SmartEnabler for SCO UNIX/ODT and
press <Enter>
2.2.4 Wait for the System to rebuild and reboot the system to
allow the new kernel to take effect.
3.0 Installation for SCO & UnixWare enabler from tar file
3.1 To install the Accton SmartEnabler from file to UnixWare:
-----------------------------------------------------------
1. Go to the /tmp in UnixWare system.
cd /tmp <Enter>
2. Copy the unwlsen.tar file from the DOS diskette to /tmp directory:
doscp a:unwlsen.tar unwlsen.tar <Enter>
3. Detar the file:
tar xvf unwlsen.tar <Enter>
4. Run the pkgadd command as follows:
pkgadd -d /tmp/unwlsen <Enter>
5. Follow the standard pkgadd installation procedure.
3.2 To build the SCO custom diskette for Accton SmartEnabler do the
following:
-------------------------------------------------
1. Go to the /tmp in SCO UNIX system.
cd /tmp <Enter>
2. Copy the scolsen.tar file from the DOS diskette to /tmp directory:
doscp a:scolsen.tar scolsen.tar <Enter>
3. Detar the file:
tar xvf scolsen.tar <Enter>
4. Go to scolsen directory:
cd /tmp/scolsen <Enter>
5. Now build the custom diskette by inserting a formatted
diskette into the drive and type:
Drive A (or drive 0)
---------------------
For 1.2M diskette:
tar c2v . <Enter>
For 1.44M diskette:
tar c6v . <Enter>
For 720K diskette:
tar c4v . <Enter>
Driver B (or drive 1)
---------------------
For 1.2M diskette:
tar c3v . <Enter>
For 1.44M diskette:
tar c7v . <Enter>
For 720K diskette:
tar c5v . <Enter>
6. Install the driver using the custom command
Drive A (or drive 0)
---------------------
For 1.2M diskette:
custom -m /dev/rfd096ds15 <Enter>
For 1.44M diskette:
custom -m /dev/rfd0135ds18 <Enter>
For 720K diskette:
custom -m /dev/rfd096ds9 <Enter>
Drive B (or drive 1)
---------------------
For 1.2M diskette:
custom -m /dev/rfd196ds15 <Enter>
For 1.44M diskette:
custom -m /dev/rfd1135ds18 <Enter>
For 720K diskette:
custom -m /dev/rfd196ds9 <Enter>
Note: This driver for SCO will auto-detect the installed
NE2000 or (nat0) driver and set the IO and IRQ
accordingly. If the NE2000 or nat0 is not installed
it will set the IO and IRQ to default values
at IO=0x300 and IRQ=5.
Note also: Please remove the old driver before installing the new one.
Appendix A: Configure the NE2K drivers for UnixWare
A-1 Configure NE2K driver for UNIXWARE
A-2.1 Install the NE2K driver supplied by Novell. The driver
must be installed at these specific I/O address and IRQ
number:
I/O base address = 0x300 (Hexdecimal)
IRQ = 10 (Decimal)
Appendix B: Configure the NE2K(nat0) for SCO UNIX/ODT
B.1 NE2K (nat0) LAN Driver installation
B.1.1 To install the NE2K for SCO UNIX a user needs to make the NAT
device:
mkdev nat <Enter>
ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³ NOTE: the enabler will detect the I/O address and IRQ ³
³ used by NE2K (nat0). ³
³ ³
³ I/O address = 0x300 ³
³ IRQ = 5 ³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.