ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ»
º º
º Compex RL100TX/10base PCI Fast Ethernet Adapter º
º (C) Copyright PDS, 1997. All Rights Reserved. º
º º
ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ
********************************************************************
NOTE:-
The "minimum packet receive buffers" must be adjusted to 150
when loading multiple frames or cards support.
Add the statement below in STARTUP.NCF file;
SET MINIMUM PACKET RECEIVE BUFFERS=150
*********************************************************************
1. NetWare v3.11 ODI Server Driver
RL100NW.LAN
This Ethernet driver is for NetWare v3.11 File Servers and complies to
Novell ODI (Open Data-Link Interface) Specifications.
2. Installation Hardware and Software Requirements:
A. Hardware Requirements:
o An IBM-compatible personal computer with 80386 or higher
microprocessor with PCI bus.
o RL100TX/10Base PCI Fast Ethernet Adapter
B. Firmware Requirements:
o Fully compliant Rev. 2.0, and 2.1 PCI BIOS supplied with the PC.
3. Supplied Files:
---------------------------------------------------------------------
README.TXT This File
---------------------------------------------------
RL100NW.LAN RL100TX Novell NetWare ODI server driver.
---------------------------------------------------
ETHERTSM.NLM Novell TSM needed to run the ODI server driver
---------------------------------------------------
MSM31X.NLM Novell MSM needed to run the ODI server driver with
NetWare v3.1X
---------------------------------------------------
PATCHMAN.NLM Novell module needed in NetWare v3.11 in addition
to MSM31X.NLM
---------------------------------------------------
LSLENH.NLM Novell module needed in NetWare v3.11 in addition
to MSM31X.NLM
---------------------------------------------------
MONITOR.NLM NetWare server MONITOR module for NetWare v3.11
---------------------------------------------------------------------
4. Installing Software:
Below are guidelines for installing the server driver, RL100NW.LAN,
in a NetWare 3.11 environment.
a. In the NetWare v3.11 directory, e.g. C:\SERVER.311
Copy all the files from NW3.11 directory of distribution disk to
the NetWare boot directory in drive C.
A:> Copy A:\NW3.11\*.* C:\SERVER.311
b. From the NetWare boot directory,\SERVER.311, run SERVER to start
NetWare.
e.g. C:\SERVER.311> Server.exe <enter>
c. At the NetWare prompt :, run LOAD INSTALL to add the following
lines to the AUTOEXEC.NCF file.
*Note:- Mount the SYS: volume if it is not mounted automatically.
: LOAD INSTALL <Enter>
select option "Edit AUTOEXEC.NCF file"
then add the following lines,
LOAD C:\SERVER.311\PATCHMAN
LOAD C:\SERVER.311\LSLENH
LOAD C:\SERVER.311\MSM31X
LOAD C:\SERVER.311\ETHERTSM
LOAD C:\SERVER.311\RL100NW PORT=nnnn
BIND IPX RL100NW net=<network cable address>
press ESC to save and quit INSTALL.
d. In Netware Server 3.11, the default "PACKET RECEIVE BUFFERS" is 10
while the PACKET RECEIVE BUFFERS requirement of RL100NW.LAN is more
than that. For the system to run properly, the following line must
be added in STARTUP.NCF file and restart the server.
"SET MINIMUM PACKET RECEIVE BUFFERS = 150"
e. When the NetWare server comes up again, Rl100TX-PCI will be
ready for operation.
Manually configuring the NetWare v3.11 server
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
At the NetWare prompt :, load the driver for RL100TX-PCI card,
: LOAD C:\SERVER.311\PATCHMAN <Enter>
: LOAD C:\SERVER.311\LSLENH <Enter>
: LOAD C:\SERVER.311\MSM31X <Enter>
: LOAD C:\SERVER.311\ETHERTSM <Enter>
: LOAD C:\SERVER.311\RL100NW PORT=nnnn <Enter>
: BIND IPX Rl100NW net=<network cable address> <Enter>
Or load NLM file seperately one at a time type the following:-
: LOAD C:\NW3.11\RL100NW PORT=nnnn <Enter>
: BIND IPX RL100NW net=<network cable address> <Enter>
The Netware 3.11 server is now properly setup.
The frame type by default is Ethernet_802.3
Below is an example to change or load additional frame type support.
: LOAD A:\NW3.11\RL100NW PORT=nnnn FRAME=Ethernet_802.2
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.