iwpriv ================= This is detailed explanation of each parameters for iwpriv. Before reading this document, make sure you already read README. ------------------------------------------------------------------------------------------------------- USAGE: iwpriv ra0 commands val NOTE: Wireless Extension Private Handlers where [commands] [val] {range} ----------------- ------------------------------------------------- wsc_conf_mode {0, 1, 2} ::Set WPS conf mode 0: WPS Disabled 1: Enrollee 2: Registrar wsc_mode {1, 2} ::PIN or PBC 1: PIN 2: PBC wsc_pin {00000000 ~ 99999999} ::Set Enrollee's PIN Code wsc_ssid {0~z, 1~32 ascii characters} ::Set WPS AP SSID wsc_start NULL ::Trigger RT2860 STA driver to do WPS process wsc_stop NULL ::Stop WPS process wsc_gen_pincode NULL ::Generate new PIN code wsc_cred_count {1 ~ 8} ::Set count of WPS credential wsc_cred_ssid {"idx ssid_str"} ::Set SSID into credtentail[idx] idx: 0 ~ 7 ssid_str: 0~z, 1~32 ascii characters wsc_cred_auth {"idx auth_str"} ::Set AuthMode into credtentail[idx] idx: 0 ~ 7 auth_str: OPEN, WPAPSK, WPA2PSK, SHARED, WPA, WPA2 wsc_cred_encr {"idx encr_str"} ::Set EncrypType into credtentail[idx] idx: 0 ~ 7 encr_str: NONE, WEP, TKIP, AES wsc_cred_keyIdx {"idx key_index"} ::Set Key Index into credtentail[idx] idx: 0 ~ 7 key_index: 1 ~ 4 wsc_cred_key {"idx key"} ::Set Key into credtentail[idx] idx: 0 ~ 7 key: ASCII string (wep_key_len(=5,13), passphrase_len(=8~63)) OR Hex string (wep_key_len(=10,26), passphrase_len(=64)) wsc_cred_mac {"idx mac_str"} ::Set AP's MAC into credtentail[idx] idx: 0 ~ 7 mac_str: xx:xx:xx:xx:xx:xx wsc_conn_by_idx {0 ~ 7} ::Connect AP by credential index wsc_auto_conn {0, 1} ::Set driver to re-connecting to AP or not after registration. 0: Disabled, driver won't re-connect to AP with new configurations. 1: Enabled, driver will re-connect to AP with new configurations. wsc_ap_band {0, 1, 2} ::Set prefer band to do WPS with dual band WPS AP 0 : prefer 2.4G 1 : prefer 5G 2 : auto Default value is auto (2) ------------------------------------------------------------------------------------------------------- USAGE: iwpriv ra0 set [parameters]=[val] NOTE: Execute one iwpriv/set command simultaneously. where [parameters] [val] {range} ----------------- ------------------------------------------------- CountryRegion {0~7} ::Set country region 0: 1 ~ 11 ch 1: 1 ~ 13 ch 2: 10, 11 ch 3: 10 ~ 13 ch 4: 14 ch 5: 1 ~ 14 ch 6: 3 ~ 9 ch 7: 5 ~ 13 ch 31: 1 ~ 14 ch (ch1-11:active scan, ch12-14 passive scan) CountryRegionABand {0~11} ::Set country region for A band 0: 36, 40, 44, 48, 52, 56, 60, 64, 149, 153, 157, 161, 165 ch 1: 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140 ch 2: 36, 40, 44, 48, 52, 56, 60, 64 ch 3: 52, 56, 60, 64, 149, 153, 157, 161 ch 4: 149, 153, 157, 161, 165 ch 5: 149, 153, 157, 161 ch 6: 36, 40, 44, 48 ch 7: 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140, 149, 153, 157, 161, 165 ch 8: 52, 56, 60, 64 ch 9: 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 132, 136, 140, 149, 153, 157, 161, 165 ch 10: 36, 40, 44, 48, 149, 153, 157, 161, 165 ch 11: 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 149, 153, 157, 161 ch SSID {0~z, 1~32 ascii characters} ::Set AP SSID WirelessMode {0~10} ::Set Wireless Mode 0: legacy 11b/g mixed 1: legacy 11B only 2: legacy 11A only 3: legacy 11a/b/g mixed 4: legacy 11G only 5: 11ABGN mixed 6: 11N only 7: 11GN mixed 8: 11AN mixed 9: 11BGN mixed 10: 11AGN mixed Channel depends on CountryRegion or CountryRegionForABand ::Set Channel BGProtection {0~2} ::Set 11B/11G Protection 0:Auto, 1:Always on, 2:Always off TxPreamble {0~2} ::Set TxPreamble 0:Preamble Long, 1:Preamble Short, 2:Auto RTSThreshold {1~2347} ::Set RTS Threshold FragThreshold {256~2346} ::Set Fragment Threshold TxBurst {0,1} ::Set TxBurst Enable or Disable 0:Disable, 1:Enable NetworkType {Infra,Adhoc} ::Set Network type AuthMode {OPEN,SHARED,WEPAUTO,WPAPSK,WPA2PSK,WPANONE} ::Set Authentication Mode EncrypType {NONE,WEP,TKIP,AES} ::Set Encryption Type DefaultKeyID {1~4} ::Set Default Key ID Key1 {5 ascii characters or 10 hex number or 13 ascii characters or 26 hex numbers} ::Set Key1 String Key2 {5 ascii characters or 10 hex number or 13 ascii characters or 26 hex numbers} ::Set Key2 String Key3 {5 ascii characters or 10 hex number or 13 ascii characters or 26 hex numbers} ::Set Key3 String Key4 {5 ascii characters or 10 hex number or 13 ascii characters or 26 hex numbers} ::Set Key4 String WPAPSK {8~63 ascii or 64 hex characters} ::WPA Pre-Shared Key WmmCapable {0,1} ::Set WMM Capable 0:Disable WMM, 1:Enable WMM PSMode {CAM, MAX_PSP, FAST_PSP} ::Set Power Saving Mode HtBw {0,1} ::Set BandWidth 0: 20Hz 1: 40Hz HtMcs {0 ~ 15, 33} ::Set MCS 33: Auto Rate HtGi {0,1} ::Set Guard Interval(GI) 0: long GI 1: short GI HtOpMode {0,1} ::Set HT Operation Mode 0: HT mixed format 1: HT greenfield format HtExtcha {0,1} ::Set Extended Channel Switch Announcement 0: Below 1: Above HtMpduDensity {0 ~ 7} ::Set The Minimum Time Between MPDUs within an AMPDU HtBaWinSize {1 ~ 64} ::Set BA WinSize HtRdg {0,1} ::Set RDG Capable 0: Disabled 1: Enabled HtAmsdu {0,1} ::Set AMSDU Capable 0: Disabled 1: Enabled HtAutoBa {0,1} ::Set Auto BA Capable 0: Disabled 1: Enabled HtBaDecline {0,1} ::Reject BA request from AP 0: Disabled 1: Enabled HtProtect {0,1} ::Set HT Protect Capable 0: Disabled 1: Enabled FixedTxMode {CCK, OFDM} :: Set Fixed Tx Mode for fixed rate setting Mode = CCK MCS = 0 => 1Mbps = 1 => 2Mbps = 2 => 5.5 Mbps = 3 => 11 Mbps Mode = OFDM MCS = 0 => 6Mbps = 1 => 9Mbps = 2 => 12Mbps = 3 => 18Mbps = 4 => 24Mbps = 5 => 36Mbps = 6 => 48Mbps = 7 => 54Mbps ==> Build Ethernet Convert function. Please set 'HAS_ETH_CONVERT_SUPPORT=y' in os/linux/config.mk EthConvertMode {dongle, clone, hybrid} ::Set Ethernet Convert Mode EthCloneMac {xx:xx:xx:xx:xx:xx} :: Set Clone MAC LongRetry {0,255} :: Set Tx Long Retry Limit ShortRetry {0,255} :: Set Tx Short Retry Limit MeshId {Length 1~32 ascii characters} :: Set Mesh ID MeshHostName {Length 1~32 ascii characters} :: Set Mesh Host Name MeshAutoLink {1,0} :: Set Mesh Auto Link Capable 0: Disabled 1: Enabled MeshAddLink {xx:xx:xx:xx:xx:xx} :: Add Mesh Link MeshDelLink {xx:xx:xx:xx:xx:xx} :: Delete Mesh Link MeshMultiCastAgeOut {20 ~ 65535 seconds} :: Set AgeOut time for Mesh MultiCast MeshAuthMode {OPEN, WPANONE} :: Set Mesh Authentication Mode MeshEncrypType {NONE, WEP, TKIP, AES} :: Set Mesh Encryption Type MeshDefaultkey {1 ~ 4} :: Set Mesh Default Key ID MeshWEPKEY {5 ascii characters or 10 hex number or 13 ascii characters or 26 hex numbers} :: Set Mesh WEP Key String MeshWPAKEY {8~63 ascii or 64 hex characters} :: Set Mesh WPA Pre-Shared Key Examples =================================================================== ------------------------------------------------------------------------------------------------------- a> Config STA to link with AP which is OPEN/NONE(Authentication/Encryption) 1. iwpriv ra0 set NetworkType=Infra 2. iwpriv ra0 set AuthMode=OPEN 3. iwpriv ra0 set EncrypType=NONE 4. iwpriv ra0 set SSID="AP's SSID" b> Config STA to link with AP which is SHARED/WEP(Authentication/Encryption) 1. iwpriv ra0 set NetworkType=Infra 2. iwpriv ra0 set AuthMode=SHARED 3. iwpriv ra0 set EncrypType=WEP 4. iwpriv ra0 set DefaultKeyID=1 5. iwpriv ra0 set Key1="AP's wep key" 6. iwpriv ra0 set SSID="AP's SSID" c> Config STA to link with AP which is WPAPSK/TKIP(Authentication/Encryption) 1. iwpriv ra0 set NetworkType=Infra 2. iwpriv ra0 set AuthMode=WPAPSK 3. iwpriv ra0 set EncrypType=TKIP 4. iwpriv ra0 set SSID="AP's SSID" 5. iwpriv ra0 set WPAPSK="AP's wpa-preshared key" 6. iwpriv ra0 set SSID="AP's SSID" d> Config STA to link with AP which is WPAPSK/AES(Authentication/Encryption) 1. iwpriv ra0 set NetworkType=Infra 2. iwpriv ra0 set AuthMode=WPAPSK 3. iwpriv ra0 set EncrypType=AES 4. iwpriv ra0 set SSID="AP's SSID" 5. iwpriv ra0 set WPAPSK="AP's wpa-preshared key" 6. iwpriv ra0 set SSID="AP's SSID" e> Config STA to link with AP which is WPA2PSK/TKIP(Authentication/Encryption) 1. iwpriv ra0 set NetworkType=Infra 2. iwpriv ra0 set AuthMode=WPA2PSK 3. iwpriv ra0 set EncrypType=TKIP 4. iwpriv ra0 set SSID="AP's SSID" 5. iwpriv ra0 set WPAPSK=12345678 6. iwpriv ra0 set SSID="AP's SSID" f> Config STA to create/link as adhoc mode, which is OPEN/NONE(Authentication/Encryption) 1. iwpriv ra0 set NetworkType=Adhoc 2. iwpriv ra0 set AuthMode=OPEN 3. iwpriv ra0 set EncrypType=NONE 4. iwpriv ra0 set SSID="Adhoc's SSID" g> Config STA to create/link as adhoc mode, which is WPANONE/TKIP(Authentication/Encryption) 1. iwpriv ra0 set NetworkType=Adhoc 2. iwpriv ra0 set AuthMode=WPANONE 3. iwpriv ra0 set EncrypType=TKIP 4. iwpriv ra0 set SSID="AP's SSID" 5. iwpriv ra0 set WPAPSK=12345678 6. iwpriv ra0 set SSID="AP's SSID" h> Get site survey usage: iwpriv ra0 get_site_survey i> Get Statistics usage: iwpriv ra0 stat ; read statistic counter iwpriv ra0 set ResetCounter=0 ; reset statistic counter j> Link with an AP which is the largest strength ; set ANY SSID (ssidLen=0) usage: iwconfig ra0 essid "" or usage: iwpriv ra0 set SSID="" k> Config STA to link as dongle mode with STA own MAC usage: iwpriv ra0 set EthConvertMode=dongle l> Config STA to link as clone mode usage: iwpriv ra0 set EthConvertMode=clone iwpriv ra0 set EthCloneMac="Desired MAC" ;; 00:00:00:00:00:00 means using STA own MAC ;; FF:FF:FF:FF:FF:FF means using source MAC of first packet coming from wired device m> Config STA to link as hybrid(dongle+clone) mode usage: iwpriv ra0 set EthConvertMode=hybrid iwpriv ra0 set EthCloneMac="Desired MAC" ;; 00:00:00:00:00:00 means using STA own MAC ;; FF:FF:FF:FF:FF:FF means using source MAC of first packet coming from wired device =================================================================== iwlist ================= This is detailed explanation of each parameters for iwlist. ------------------------------------------------------------------------------------------------------- iwlist ra0 scanning ; list the results after scanning(manual rescan) ======================================================================================================= iwconfig ================= The following are our support in standard configuration - iwconfig ------------------------------------------------------------------------------------------------------- iwconfig ra0 essid {NN|on|off} ; set essid iwconfig ra0 mode {managed|ad-hoc|...} ; set wireless mode >> rt2860sta driver support monitor mode with linux kernel > 2.4.20. >> Note: For using monitor mode => if mesh interface is ON, please down the mesh interface first. iwconfig ra0 freq N.NNNN[k|M|G]] ; set frequency iwconfig ra0 channel N ; set channel iwconfig ra0 ap {N|off|auto} ; set AP address iwconfig ra0 nick N ; set nickname iwconfig ra0 rate {N|auto|fixed} ; set rate (only support legacy rate setting) iwconfig ra0 rts {N|auto|fixed|off} ; set RTS threshold iwconfig ra0 frag {N|auto|fixed|off} ; set Fragment threshold iwconfig ra0 enc {NNNN-NNNN|off} ; set encryption type iwconfig ra0 power {period N|timeout N} ; set power management modes *** Wireless extension usage please refer to man page of 'iwconfig', 'iwlist' and 'iwpriv'. ***Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.