######## /etc/X11/xorg.conf ######## ############################################################################## # Device # COM : /dev/ttyS0, /dev/ttyS1... # USB : /dev/input/event3, /dev/input/event3... ############################################################################## Device=/dev/input/event5 ############################################################################## # Protocol : PM9000, PM5000, PM6000USB, PM6000COM, PMLPC ############################################################################## Protocol=PM6000USB ############################################################################## # Baud Rate for PM9000 and PM6000COM : 19200 or 9600 ############################################################################## BaudRate=19200 ############################################################################## # PenMount configuration file ############################################################################## ConfigFile=/etc/penmount.dat ############################################################################## # Option AlwaysCore in Section ServerLayout ############################################################################## AlwaysCore=1 ############################################################################## # X window Screen Number (default = 0) ############################################################################## ScreenNumber=0 ############################################################################## # PenMount A/D bit : 10-bit or 12-bit ############################################################################## ADBit=10 ############################################################################## # XRandR : 1=XRandR enable, 0=disable ############################################################################## RandR=0 ############################################################################## # Debug for PenMount X input driver ############################################################################## DebugLevel=0 ######## /etc/penmount.dat ######## ############################################################################## # Send (left/middle/right) button when press and hold/ # e.g. : RightButton / MiddleButton / LeftButton # P.S. : RightButton : button 3 # MiddleButton : button 2 # LeftButton : button 1 ############################################################################## PressAndHoldButton=RightButton #PressAndHoldButton=MiddleButton #PressAndHoldButton=LeftButton ############################################################################## # Click Mode Pen Down Pen Hold Pen Move Pen Up #--------------------------------------------------------------------------- # MouseEmulation : LEFT-DOWN -------- -------- LEFT-UP # PenInputEmulation : # ClickOnRelease : --------- -------- -------- LEFT-DOWN-UP # ClickOnTouch : LEFT-DOWN-UP -------- -------- ------- ############################################################################## #TouchMode=ClickOnTouch #TouchMode=ClickOnRelease #TouchMode=PenInputEmulation TouchMode=MouseEmulation ############################################################################## # Press and hold function switch (1=on, 0=off) ############################################################################## HoldSwitch=1 ############################################################################## # Hold time for Press and Hold (unit : mini seconds) ############################################################################## HoldTime=800 ############################################################################## # Hold Area is for press and hold, calculate the distance of # current X,Y and pen-down X,Y # if distance > HoldArea : PRESS AND HOLD IS DISABLE # distance <= HoldArea : PRESS AND HOLD IS ENABLE (when over hold time) ############################################################################## HoldArea=32 ############################################################################## # Scale to screen resolution # 1=enable (screen resolution) e.g. 1024x768 --> 0~1023 and 0~767 # 0=disable (panel resolution) e.g. 0~1023 and 0~1023 ############################################################################## ScreenScale=0 ############################################################################## # Fuzz Point # 0 : disable # 1 : Linux input fuzz # 2 : four-points average # 3 : eight-points average # FuzzValue is used for Linux input fuzz ############################################################################## FuzzPoint=0 FuzzValue=2 ############################################################################## # Rotation # 1 : normal # 2 : left (90-deg) # 4 : inverted (180-deg) # 8 : right (90-deg) ############################################################################## Rotation=1 ############################################################################## # Edge Compensations for calibration ############################################################################## XMinOffset=10 XMaxOffset=10 YMinOffset=10 YMaxOffset=10 ############################################################################## # Beep Configuration ############################################################################## # BeepType = 0 : Slience # = 1 : Beep when pen down # = 2 : Beep when pen up # = 3 : Beep when pen down and pen up # # BeepFreqDn / BeepFreqUp # Beep Frequency for pen down and pen up # # BeepDelayDn / BeepDelayUp # Beep delay time for pen down and pen up # (unit : mini seconds) ############################################################################## BeepType=1 BeepFreqDn=880 BeepDelayDn=100 BeepFreqUp=1200 BeepDelayUp=100 ############################################################################## # Calibration Configuration ############################################################################## # CalibType = 2 : standard calibration # = 4 : 4-points calibration # = 9 : 9-points calibration # = 16 : 16-points calibration # = 25 : 25-points calibration # # CalibType=2, CalData=Xmin,Xmax,Ymin,Ymax # CalibType=4, CalData=X0,Y0,X1,Y1,X2,Y2,X3,Y3 # CalibType=9, CalData=X0,Y0,X1,Y1........,X7,Y7,X8,Y8 # CalibType=16, CalData=X0,Y0,X1,Y1........,X14,Y14,X15,Y15 # CalibType=25, CalData=X0,Y0,X1,Y1........,X23,Y23,X24,Y24 ############################################################################## CalibType=4 CalibData=1932,1912,120,1944,102,98,1972,94 ############################################################################## # Mapped Monitor Settings ############################################################################## Monitor=default ############################################################################## # Jitter Filter ############################################################################## JitterFilter=8Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.