README.TXT Driver File Contents (


                      Accton Technology Corporation
     Packet Driver Installation for EN1203, EN1207 Series Ethernet Adapter

Copyright (C) 1995, 1997 by Accton Technology Corporation.
All rights reserved.

The driver PCIPD.COM can be used for the following Accton Ethernet adapters:

           EtherDuo-PCI              ( EN1203 )
           Fast EtherCombo-TX PCI    ( EN1207 )
           Fast EtherPair-TX PCI     ( EN1207 TX or B )

PCIPD syntax:

PCIPD  [-#] [-a] [-b] [-t] [-f] [-s] [-d] [-n] [-w] [-u] [-h] <PD_INT_NO>


[-#]           The "-#" option will let driver work on a specific adapter
               when multiple Accton's PCI adapters are found in the computer
               system.  For example, "-1" means the first adapter will
               be activated by the driver, "-2" means means the second
               adapter will be activated, ... etc.
               A maximum of 4 adapters are supported simulaneously.

[-a]           The "-a" option will let driver perform automatic media
               detection during driver initialization.  The detection
               sequence is

                 A.> EN1203 adapter
                     TP  10Mbps --> BNC 10Mbps

                 B.> EN1207 adapter
                     TP 100Mbps --> TP  10Mbps --> BNC 10Mbps

                 C.> EN1207 Series adapter
                     TP 100Mbps Full Duplex --> TP 10Mbps Full Duplex
                 --> TP 100Mbps Half Duplex --> TP 10Mbps Half Duplex

               If no physical media is attached to the adapter then
               BNC 10Mbps is the default media for both EN1203 and EN1207,
               and TP 100Mbps Full Duplex is the default media for EN1207

[-b]           The "-b" option is use Coaxial Cable(BNC)(10BASE-2) as
               transmission media.

[-t]           The "-t" option is use Twisted Pair(RJ-45)(10BASE-T) as
               transmission media. And it is also default setting.

[-f]           The "-f" option enables FULL_DUPLEX feature of the adapters.
               It make no effect except Twisted Pair is used.

[-s]           The "-s" option set adapter line speed to 100Mbps.  It is a
               dedicated option for EN1207 Series fastnet adapter.

[-d]           The "-d" option does not start LAN card until this driver is
               called by the higher layer programs first.

[-n]           Your  NOVELL server uses NOVELL ISO-like packets. Your NOVELL
               workstation uses  NOVELL 8137 packets. You can use this option
               to convert NOVELL 8137 packets into  NOVELL ISO-like packets.

[-w]           Steve Wallace added a hack to let the packet drivers run under
               Windows. This is not to be construed with the proper solution,
               which is to write a TCP/IP package for Windows.

               This hack is enabled only when you use the '-w' switch.

[-u]           This option unloads the Packet Driver.

[-h]           This option displays the on-line help.

<PD_INT_NO>    This specifies the software interrupt (INT) where  you'll
               load the packet driver. It must be in the range 0x60 to 0x80.

Notice!!       The PC/TCP kernel, by default, is loaded at interrupt 0x61
               (so don't load the packet driver there!)


The following command line loads the Accton EN1203, EN1207 Series adapters
Packet Driver at software interrupt 60h, transmission media is

PCIPD -a 0x60  or PCIPD 0x60

Note: The default transmission media is automatical-detection.
Note: The placement of 0x prior to the parameters.

After the Packet Driver is loaded, you can run the PC/TCP kernel ETHDRV.EXE.
The PC is then ready for PC/TCP communications.

To run PC/TCP applications, You need to load PC/TCP Kernel

    a. Refer to PC/TCP manual, Command Reference
       section, Chapter 2.3.

    b. The following example loads the PC/TCP Kernel and allocate 8
       packet buffers.  Increasing the packet buffer numbers (from the
       default of 5) prevents dropping of packets due to buffer shortage.

       ETHDRV -p 8 <Enter>

    c. At this point, you are ready to run PC/TCP applications
       (e.g., 'ftp', 'telnet').
       example ftp ,  is host address.
       Regard to host address , you must know its address.

      For information regarding the "FTP's PC/TCP Network
      Software for DOS" packages, please

      FTP Software, Inc.
      26 Princess Street
      Wakefield, MA  01880
      (617) 246-0900

How to Communicate with NCSA TelNet.

1. Make sure you have the correct version of NCSA Telnet
   for the PC. You need version 2.3 or later to support
   the packet driver interface.

2. Install the NCSA software onto your system. Please
   refer to the NCSA documentation for detailed instructions.

3. Load Packet Driver (PCIPD 0x60):

   a. Refer to "Packet Driver Syntax" section above.
   b. To view the hint screen, type

      PCIPD -h <Enter>

   c. The following example will load the packet driver
      using interrupt vector 60 (hex).  The IO_BASE
      and IRQ will be read from adapter configuraion space:

      PCIPD 0x60   <Enter>

4. At this point you are ready to run NCSA applications
   (e.g., 'ftp', 'telnet', etc.)

   for example : ftp,
                 while is the host address.

      For information regarding NCSA's products please

      National Center for Supercomputing Applications
      264 Computing Applications Building
      605 E. Springfield Ave.
      Champaign, Ill. 61820
      (217) 244-0638

--- End of File ---

Download Driver Pack

How To Update Drivers Manually

After your driver has been downloaded, follow these simple steps to install it.

  • Expand the archive file (if the download file is in zip or rar format).

  • If the expanded file has an .exe extension, double click it and follow the installation instructions.

  • Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.

  • Find the device and model you want to update in the device list.

  • Double-click on it to open the Properties dialog box.

  • From the Properties dialog box, select the Driver tab.

  • Click the Update Driver button, then follow the instructions.

Very important: You must reboot your system to ensure that any driver updates have taken effect.

For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.

server: web3, load: 0.82